e3d tool changer direct drive

The human-designed 18mm version of the E3D carriage without a cable duct for ejpsx was nowhere to be found, so I'll provide it here. ... #define X_PROBE_OFFSET_FROM_EXTRUDER 20 #define Y_PROBE_OFFSET_FROM_EXTRUDER 10

The heatsink fan is 30x30x10 and the part cooling fan is 40x40x20. ...Will fit an e3D Volcano. it is also set up for a Bondtech BMG. ...Drilling is required.

For Hypercube Evolution New X-Carrier Car with Integrated Optical Endstops NEW Part Cooling Fan, Adjustable Added Mounting Plate for E3D Titan https://e3d-online.com/titan-extruder E3D Hotend Lite https://e3d-online.com/lite6 BL-Touch...

18mm version without cable duct for ejpsx's E3D carriage was missing, so here it is. ... "#define X_PROBE_OFFSET_FROM_EXTRUDER -20" "#define Y_PROBE_OFFSET_FROM_EXTRUDER -10"

Print Bigger, Stronger & Faster Boasting 3x the volumetric flow rate of the V6, the E3D Volcano enables you to print bigger and stronger parts, faster. This 3d printed mount allows you to install the E3D Volcano hotend and the BondTech BMG on your...

This is a part cooling fan mount/duct, that I designed for lipki's direct drive extruder design: https://www.thingiverse.com/thing:2665491 This was my first attempt to create a fan duct, so it certainly has room for improvements. I couldn't find a...

This is a mount for the E3D titan extruder (klemco all metal extruder shown here) and the V6 hotend. It includes:Sensor mount holes for Z axis sensorBelt connections for the X axis belt. Beveled for easy access to the extruder tensioner.

To accommodate users who favor the JHead mount system, this updated design optimizes the groove dimensions to ensure seamless compatibility with that platform, thereby eliminating previous concerns that might have arisen from differences seen on the...

This is a remix of Wundel's Ender 3 Direct Drive conversion kit, showcasing impressive promise, but unfortunately, two negative comments arose - one concerning the oversight of a spot to tie cables and another regarding tilting the 5015 fan at 45...

For the temperature sensor, I am using a PT100 sensor from E3D so that is why I chose to use that particular connector on the PCB. For the motor and fan connections, I simply soldered the wires directly to the board (from the back, in order to hide...

The hollow threaded rod that mounted the MK8 hot end to the lower part of the filament tension bracket is what you'll use to secure the stepper motor to the E3D hot end. Simply spin the E3D hot end until the motor securely attaches to the mount. ...This...

This is a universally (and my universally I mean people with e3d v6 hotends) mount to hold a hotend cooling fan, part cooling fan, and a touch mount. I designed this based off an earlier design, but I despised how the bltouch and everything else...

The E3D all-metal hot end and long heat break make this configuration optimal for printing in ABS, and the Thing-O-Matic is excellent for printing in ABS given the small build platform and easily enclosed frame. I've owned my MakerBot...

Here's a breakdown of the document: **Introduction** * The document outlines changes necessary to upgrade a UM2 printer to use the E3D hot end and other modifications. **Before Running Motor** * Before running the motor, decrease the milliamps...

Remixed a standout design to incorporate support for a DiiCooler, taking into account the unique specifications of the E3D vulcano. The Vulcano boasts a longer head compared to the v6, necessitating the use of extended screws and additional nuts to...

Use this with my dual motor mount X-carriage: http://www.thingiverse.com/thing:497661 Follow instructions for screws and parts from this remix I made: http://www.thingiverse.com/thing:524249 If your first extruder is on the left, reversed side, you...

Use this with my dual motor mount X-carriage: http://www.thingiverse.com/thing:497661 Follow the instructions for screws and parts from this remix I made: http://www.thingiverse.com/thing:524249 If you put your first extruder on the left (the...

I upgraded the hot-end on my Prusa i3 to an E3D V6, and wanted to continue using the auto levelling sensor that I had previously installed. This is the sensor it was designed for:...

This is my addition to a very cool E3D V6 mount for CR-10: https://www.thingiverse.com/thing:2494642. This part mounts using 2 screws to the CR-10 hot-end plate: the lower one of those that would normally mount the CR-10 hot-end housing and the...

Additionally, I added more clearance for the heat sink fan, an EzABL probe mount, space for an e3d collet clip above the heatsink to lock in place the PTFE tube, and heat sink exhaust channels to encourage smoother air flow of hot air. I also added...

I increased its width to accommodate a 12.64mm drive gear for better performance. Additionally, I drilled out a 3mm hole on one side to make it compatible with a wide range of exotic filaments. ...I hope you find this part useful and would appreciate...

I designed this mount specifically for the Direct mod BMG + E3Dv6 on openbuilds carriages, which are commonly used by Creality, Tevo, and Alfawise users. The original BLTouch was notoriously fragile when attempting installation, so I beefed up the...

I changed the direction and size of the blowing nozzle so that the air stream falls under the nozzle, the size of the hole for the fastening nut (previously the nut did not fit), the size of the duct channels so that the air flow is large. Maybe not...

NOTE: this mount is for Direct mod BMG + E3Dv6 for openbuilds carriage (Creality, Tevo, Alfawise, etc) The original BLTouch was very fragile when trying to install, so I reinforced the screw hole. Additionally, I added a rail-like system to prevent...

I managed to find a way to align dual extruders in the y-direction, freeing up valuable space on the hotbed. One-piece designs often prove challenging without supports, and attempting to print with them results in a non-functional outcome. After...

This adapter allows Alfawise/Longer users to mount a BMG extruder directly above their V6 hotend while still using the fang cooling ducts. It also includes an extended bump for the x-axis stop switch so the motor doesn't slam into the frame. Yes,...

I wanted to use the fan-shroud of the Prusa I3 mk3s+ model, Since I already own an I3 mk3s printer, I created a new modeling file by directly measuring the approximate location of the shroud. The result of the application is somehow successful,...

Note: If it's your first attempt at direct extrusion, you might want to decrease print speed and acceleration on the X-axis because there is more weight on the sleigh than before. Bugfix01: Mounts of 2ndFan too long -> chopped Update: There is...

Instead of directly screwing into the plastic, I installed brass inserts for M3 screws. The fan shroud comes from the Prusa MK3 R3. The cold end fan is a 40x40x20 Noctua fan, and the part cooler fan is a Sunon 5015. A comparison on the weight of...

https://www.thingiverse.com/thing:3913249 https://www.thingiverse.com/thing:3599905 https://www.thingiverse.com/thing:3603004 https://www.thingiverse.com/thing:2425783 However, I didn't like the set of Fan-shrouds provided, and even touched the...