e3d titan stl

I bought mine from PrintedSolid.com (https://printedsolid.com/products/e3d-titan-extruder). I have been working on a bracket for my Robo3d since they didn't release brackets for all printers yet. I've included the STEP files if you want to...

I use an E3D Titan Aero with a volcano heatblock on my Anycubic Mega X. Also tried out some of the existing fan ducts but either they didn't work very well for me, or they were a bit too clunky and heavy for my taste. On some of my other printers I...

I meticulously replaced the main circuit board with a Duet WiFi unit and swapped out the nozzle for a Titan Aero from E3D. To get started, you'll need several key components: You'll require four 80mm M8 rods (you can easily cut these from a single...

This is an insert to replace the filament guide between the hotend and the filament gear in E3D Titan Aero to better control flexible filaments. I bought a direct drive Titan Aero to work more with flexible filaments on my railcore 2 build. This...

BLTouch Mount for E3D Titan Extruder. This design serves as a starting point for creating a custom BLTouch mount that can be adapted to various printer X carriage types. It is an addition to my cooling fan mount, which can be found at...

I use an E3D Titan Aero with a volcano heat block on my Anycubic Mega X.Also tried out some of the existing fan ducts but either they didn't work very well for me, or they were a bit too clunky and heavy for my taste.On some of my other printers I...

E3D Titan Aero High Temperature Fan Duct. Designed to control the airflow from the Titan Aero and direct it upwards away from the heated bed. Requires that the included Titan Aero Fan be reversed to draw air through the heatsink rather than blow it...

This is a custom side mount designed specifically for my Foldgertech i3 2020 printer, which features the E3d Titan Aero installed on its original stock mount. This modification enables thermistor and heating element wires to run up the side behind a...

This is a 50mm Fan duct that mounts on the small cooling fin at the top of the E3D v6 hotend under the titan extruder Print Settings Printer: cartesian Rafts: No**Supports:** No Resolution: 12.5**Infill:** 100 Filament: sunlu PLA+ How I Designed...

A remix of the E3d Titan Mount for M8 Threaded Rod designed to sit atop the top bars of a RepRapPro Mendel / Tricolour. ...Both open and closed versions are provided - the open one can simply drop onto the bars, while you'll need to remove the top bars...

... My goal was to attach an E3D Titan extruder with hotend to the original nozzle position on this printer. ...To make it work, I needed a short piece of the aluminum frame from the Velleman K8200 3D printer as well as an additional edge bracket.

Modified mkelly's base carriage was discovered to fit E3D's Titan Aero perfectly. https://www.thingiverse.com/thing:647798 After printing the part in transparent yellow PETG, I have not yet tested the cable chain link. The link is designed to fit an...

I'm thrilled to finally have a home for my inductive sensor now that I've got my E3d Titan Extruder up and running - it's been a game-changer so far! The one thing holding me back was figuring out where to place this essential component, but no more!...

I have designed a custom mount for the E3D Titan, specifically tailored to fit the HyperCube CoreXY 3D printer with a DC42 IR probe installed. The main mounts feature M3 threaded 4mm knurled inserts for added durability. For this design, I recommend...

After a successful partnership with E3D on their latest venture, here are the components to print for upgrading a Prusa i3 printer to fit their innovative Titan Extruder and HotEnd eco-system. I recommend referring directly to the E3D Wiki where I...

I designed a direct drive, lightweight carriage for the Anet A8 that leverages the E3D Titan extruder's capabilities, including its light weight and ability to print flexible filaments. This setup uses the smaller and lighter pancake motor. In Fusion...

You can find more information and pictures in the following thread: https://forum.e3d-online.com/threads/3mm-wiring-forces-and-toolchanger-docking-challenge.3446/ My tool offsets are set as follows: G10 P0 X14.1 Y59.75 Z-7.60 ; T0 TitanAero 3mm G10...

It features a Titan extruder from e3D for direct-drive printing with either 3mm or 1.75mm filament. The redesigned carriage is about 15mm wider than the original, which reduces the usable X-axis width, and the cage fan on the back similarly decreases...

My Version of the E3D Titan Extruder Clip for the Palette 2/Pro's Output Tube. I Discovered xile6's Version but Wasn't Impressed by the Titan's Bowden Tube Being the Only Support, So I Designed This Version from MosaicResources'. Similar to xile6's...

This is a mount for an 18mm inductive sensor specifically designed for the E3D Titan Extruder. While many people prefer to use inductive sensors with a 12mm diameter, I acquired one with an 18mm diameter. As a result, I can run this sensor on 5V and...

E steps have to be adjusted in Firmware to 837 Steps-per-mm (see E3D Titan documentation) The nozzle is about 7mm closer to the heatbed, so you have to pay attention to your z-axis endstop - otherwise the nozzle will run into the bed. I solved this...

This mount is specifically designed for the E3D Titan extruder and Wilson TS X-carriage mounting style, similar to the Prusa i3 Rework. I was dissatisfied with other mount designs that required me to remove the entire X-carriage, so I created this...

This is a mount designed to attach a Duet3d filament sensor (https://duet3d.com/wiki/Duet3d_Filament_Monitor) to an E3D Titan (https://e3d-online.com/titan-extruder) when used in a bowden setup. It replaces the aluminium bowden adaptor and places...

Here are the dock/tool adapters to support four Titan Aero extruders on the E3D ToolChanger. Note that there are two sets of holes for aligning dock-adapter-bottom with top-plate, creating an x-offset to support larger 'Compact but Powerful' stepper...

This bracket is designed for mounting an E3D Titan extruder on a Velleman K8200 printer. My own printing experience led me to use 40% infill and 0.8mm shells in black PLA. Note that the bracket requires four screws, two from below and two at the...

This is what my probe offsets are: X_PROBE_OFFSET_FROM_EXTRUDER -23 // X offset: left of the nozzle Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: behind the nozzle Z_PROBE_OFFSET_FROM_EXTRUDER -1.2// Z offset: below the nozzle Follow the instructions...

I've upgraded to a Titan Extruder and an E3D Hotend, both of which are reputable knock-offs that work flawlessly. To ensure precise alignment, I've installed a BLTouch sensor right next to the nozzle. All standard cooling fan, extruder stepper...

Designed for the Folgertech FT-5 with the E3D Titan Aero, this print is tailored to perfection. After thorough testing, it was found to be a snug fit, but fortunately everything fell into place on a friend's machine. Another user has cautioned that...

Needed a place to mount my new e3d Titan extruder and wanted it close to stock location but also facing me so had to rotate stepper 90 degrees from stock figured could use one of screw holes on stock bracket with longer (18mm M5) screw in its place...

I'm designing the E3D Titan Extruder mounting bracket for use with 20x20 profiles. The printing settings are optimized for a smooth finish and stable build plate adhesion. My printer of choice is the sparkcube, which delivers precise control over...