e3d rc plane

A simple and versatile servo horn designed to work seamlessly with elevons, ailerons, or rudder systems.

E‑flite EFLU1180 UMX Carbon Cub SS  Replacement Rudder.  Pretty close to the original with a tiny carbon fiber hinge pin.  I have given these to friends who have damaged the already-very-fragile tail fin.  This rudder will take a lot more abuse. ...

Simple Wall hanger for large airplanes / sailplanes (up to 3 meters) 2 arms versions 10 or 5mm wide Infill between 5 to 10 % printed with a large brim to avoid warping assemble with CA

A versatile hanging solution designed exclusively for small aircraft. ...Constructed to accommodate my trusty Phoenix Volantex, this sturdy wall mount features an expansive backing that allows users to securely fasten it with double-sided tape or...

Person: Individual operates a wheel with an outer circumference of approximately three inches nine millimeters, supported by an axle that measures roughly one-eighth inch in diameter.

Mastered it hasn't been, yet this was a project that consumed considerable time and effort.

We're planning to 3D print Weel (däck) using flexible filament, but so far we haven't attempted printing it with that material yet. ...The rest of our prints have been made from PLA or ABS.

The clevis is straightforward to design, and I made it slightly longer than usual (about 35mm instead of the standard 20-25mm) because after repairing my elevator's string, it came out a bit shorter. ...The prints are done with 100% infill.

Model airplane enthusiasts are perfecting a lightweight flying machine that attaches to a radio controller and features a robust design.

A tail wheel frame for my Hobbyking Hummer.

These are wheels for radio control airplanes. I modeled them after 35" Alaskan Bushwheels. I've included models for 50 mm (2"), 44 mm (1.75"), and 15 mm (1") with 1.5 mm and 3 mm axle sizes. Print them in two halves, clean the axle holes out with...

I modified some equipment on my Thunder Tiger Cessna 177 so I can take off and land on snowy or icy surfaces during the winter months.

A custom-built holder crafted specifically for 1 millimeter diameter wire, fabricated through precise three-dimensional printing technology at a layer thickness of 0.1 millimeters.

This hinge is engineered to attach seamlessly onto control panels, yet its design allows for effortless modification to accommodate screw installation if desired. ...Through strategic mating within the assembly process, the hinge can be manipulated to...

People are creating models specifically designed to be printed using three-dimensional printers.

This is a control horn designed for use on remote-controlled airplanes. I created it initially because my WindRider BD5 came with one missing part. It was printed in PETG and Glass Filled PETG, which couldn't be snapped by hand along the lines where...

I decided to remake the model a little. Changed engine mounting, square cutting, winglets and servo pad.The final result is not yet ready. ...There is still preliminary data here.Note: The Krilo-30 version already with smoother shapes.Although some...

A truly successful endeavor. ...The human element proved to be a valuable asset as CDI boldly moved forward with unwavering support, never faltering or losing its footing in the process.

Hello, This is upgraded motor hanger for LRP upstream or bixler so its universal motor hanger. It's better to be printed with Petg or stronger plastic not PLA but it's not the worst chose. ...

PLA 25% https://youtube.com/shorts/6cylg_HfPPI?feature=share

Nylon pinned hinge 16x28.5mm.Model was made with FreeCAD

This design attaches wings and a tail fin, allowing you to add rods for extra support. Once I print it out, I'll share a photo of the finished product. For now, I'm unsure if additional supports are necessary. Just printed the pieces and a few need...

I'm not too keen on 'Z' bends on pushrods either. They often have too much slack or are way too tight, making them sloppy to work with. Plus, once a 'Z' bend is installed, the pushrod can't be easily removed - it's stuck in place. That's why I came...

I've Included Both a Flat Bottom and Curved Version The Curved One's Located on My Phantom FX-61, While the Flat One's Mounted on My Hazzard FPV 29-Inch Flying Wing. ... This Setup Suits a 40-Millimeter Launch Ring.

fun jet cooling scoop

This is a versatile pylon mount I designed that can accommodate any type of ordnance. All you need are two zip ties to secure the ordnance to the pylon, making it an incredibly easy setup. While it may not be the most conventional method, it's...

The pilot slides the airplane onto a 5mm thick pad of soft foam to ensure a safe and secure landing experience.

I picked up some spare parts for my Hacker Funmaster project, including a fix for the finicky landing gear that kept pulling out on me. To keep it from happening again, I came up with a simple but effective holder to keep everything secure.