e3d nozzle

Printing is to be done at 0.1 mm layer height with 0.2mm thickness (ideally using a 0,2mm nozzle), generating supports with an angle cap of 30 degrees. If printing everything in one go it is recommended to print at 80%< infill, in order for...

The hubs can be reused!Filament usageFor a spool with 80 mm axle diameter, structural size of 8 mm, printed with 15% infill, no rafts and no supports:Hub:23 gSpoke:9 gLabel:12 g  Total for spool with two hubs with standoff, three spokes and...

 Ensure you are editing the correct point or you may plunge your nozzle into the bed.  If unsure then just raise a specific point up 2mm, print the squares and when it tries to print in mid air you will know what coordinates correspond with...

Any prospective assemblers will need to pay attention to how I have constructed my bottom frame, with the two wide 2020 extrusions, set back 20mm from the front and back of the bot. The models were printed in solid ABS, using a 0.8mm volcano nozzle...

It would be easy to make custom traveling objects from an infinite variety of designs.PRINTING:Print the two unique halves, two springs, the arc that you want to print, and the object(s) that you want to print.NOTE:     if you are printing...

The side-walls were optimized to be printed with a 0.4mm nozzle and minimum amount of retractions needed for smooth, fast and easy printing. The box lid will clip onto the rails in the box. However if you want to secure them you can print up to 4 of...

This is used to construct the spool stand.Print SettingsPrinter Brand: PrusaPrinter: i3 MK3S MMU2SSupports: NoResolution: 0.4mm nozzle, 0.3mm layers (draft mode)Infill: 15% gyroidFilament: Prusa PLA or PETG for stand, PLA for axleNotes:Use a 4-5mm...

Simple bricks to play with or to integrate into other projects, designed to be easy to print, and easy to integrate in all other projects.Printing parameters:PLA//0.4 nozzle//0.2 layer height//0%infill//no support//brim All the parts in the files are...

As a result, I made the brackets and logo containing bars only have color on the top and bottom surfaces (based on print orientation), and the multi-color portions are only 2-3 layers thick (depending on nozzle and layer height).For the brackets...

this may be a result of how many variables there are with different filament out in the world, thus a solution has been offered.GCODE files have been provided for every variant of the two main body designs and the updated spindle designs, including...

Printed at 0.2 layer height with a 0.4 nozzle.Printing all-in-one:You can use the provided Prusa Slicer project for printing all the pieces in a single printing run, here you will not need to run any tuning other than selecting the correct filament...

As always, the .blend file and pre-supported .obj (the one that I used to print it on my Prusa mk3 with a .25 mm nozzle) for this model are available to my patrons at https://patreon.com/VirtuallyJason. If you appreciate my work and have a few...

The Nozzle piece glues into the end of the Front piece and then can be slid over the barrel section of the launcher. The fit should be snug but can be fixed in place with glue. The Rear part attaches to the back of the grenade launcher with the two...

All parts use a 0.4 mm nozzle, PLA/PLA+ and a 0.2 mm layer height. Parts List Brett OliverParts by Brett Oliver Part...

I hope they take less power than the volt regulator that is taking up to 3v. All except battery cover does not need supports, they are built into STL, easy remove after print. 4mm FDM Nozzle, 5mm line and parameter width, 0.2mm layer height. Bridge...

Ensure the “Top Jig” piece is oriented the correct way prior to printing.Setup and UseFollow these steps to ensure flawless use.NOTE: This was printed with a .6mm nozzle.Setting the alignment magnets:CenterMag Setting:Insert the magnet in any...

I inspired from these to create this circular version.The mechanism is pretty simple : the first wheel hold the wave and turn anti-clockwive while the second wheel hold the pales and the boat and turn clockwise.I added a reduction gears system on the...

(extra screw holes are available if you plan to stack more than 2 rows of drawers or contents of heavier than normal weight.) RECOMMENDED PRINT SETTINGSFilament: PLA (PETG or ABS for heavier duty storage)Nozzle Size: 0.4mmPrint Height:...

They have a couple stop pegs that insert into the grill slots allowing for positive open and close stops.Camera ClipsI mounted three webcams on the case: one to look down form above at the print bed, one on the X-Axis Motor to look at the print bed...

The flex is also needed to press fit the mount which gives us extra friction to hold the lamp in place.The Light Cap part is optional but highly recommended and shields the rider eyes from the lamp from above, it's a thin piece that is slotted in...

The “Left_Side.STL”, “Right_Side.STL and “Inside_Parts.STL” have all the components in separate files in case you want to print with different colors or your print bed is less than 200mm.I printed the parts with ABS using support for the bottom...

Personally I printed my parts on a slightly modified Ender3 V2 using E-Sun PLA+ (gray) with a stock 0.4mm nozzle. In terms of the printing itself, these parts don't need any support. Orientation wise the case, tray and switch can be printed as...

In the OpenSCAD source file, all of my changes are indicated by a comment starting with //am.Print SettingsPrinter Brand: PrusaPrinter: i3 MK3S MMU2SSupports: NoResolution: 0.4mm nozzle, 0.2mm layersInfill: 15% gyroidFilament: Prusa PLA for stand,...

Might I suggest a Raspberry Pi 3 with Octopi installed?Octoprint "GCODE Scripts"After print job is pausedM117 Print Paused{% if pause_position.x is not none %} ; relative XYZE G91 M83; retract filament, move Z slightly upwards G1 Z+5 E-5 F4500;...

So the steps are: #1 glue magnet into MagnetMount, #2 press the mount on the screw - do not glue yet, #3 test direction and adjust mount, #4 once it matches, mark direction with a pencil and glue MagnetMount to the screw.The wind mount has a M6...

Have read that it fits the  X Max 3 without any conflict!   Presented below, Provides a gap to cut the filament without any ptfe tube handling.  Works well, light weight, no stress to the print head when cutting, and no conflict with the print head...

Here's some printer and PrusaSlicer settings I used: 0.4mm nozzle 100% infill (say yes to the infill pattern suggestion) 0.20 QUALITY PLA works. I'm sure other materials will work too, but unsure how rigid they'll be.</li> </ul> <p>Note: other...

You should only insert the NFC chip in the end because otherwise the hot nozzle could possibly damage your NFC chip and make it unusable.You can also use the color switch to stop the printer at a specific layer or height and don't switch the filament...

The walls of the cup holder “surface” are 1.6mm, with the intent that a 0.4mm nozzle will yield no “infill volume” if you use the typical 2 walls in your slicer settings (2 inside walls + 2 outside walls = 4 total wall width = 1.6mm) a. Note: My...

... noisy than values that aren't divisible by 0.04. This will vary based on your printer, but lots of them can use 0.04 as a starting point. Some can use increments of 0.02. I could have printed this with 0.4mm layer height on my 0.6mm nozzle. ...