e3d nozzle vs clone

They fit very perfectly on the clone e3d heads, and they resist high temperatures much better than the original blue socks I was tying to my clone head with wire. For example printing nylon at 260C, the blue ones got hard and developed a whitish...

This engineer designed a holder for optimal viewing under the nozzle without battery-powered lighting. Due to limited space, a standard LED strip was not feasible, so they utilized a single LED chip from a daylight-enhanced strip instead. The LEDs on...

A 1/8" npt female pipe thread at the top of the nozzle engages the plastic nub, maintaining alignment. This model is parametric and can be modified in Inventor if modifications are needed to the nub diameter or design. The split opening acts as a...

Clone a Fan Duct Specifically Designed for the E3D V6 Heatsink on a J-Head.

This design appears to be a clone of the E3D-China V5 model. Its purpose could potentially be useful for creating custom printheads and cooler brackets. ...Edit: Confirmation has been made that this is indeed an E3D V5 model.

I designed an E3D Clone Fan Duct using Tinker-Cad, which accommodates a 40x40mm fan perfectly. ... The Heatsink Dimensions I Specified Are: Diameter: 25 millimeters Length: 32 millimeters

I have a Chinese clone of titan extruder, I wanted to edit something in the cover, but unfortunately, I didn't find an accurate cad for this clone.so I take the available one from:...

It was based on dimensions from E3D's website for the original part, not the clone I have, which explains this discrepancy. So, I recreated the mockup using calipers and this version matches my clone almost perfectly. The heat block is correctly...

For 25mm chinese clone

A rework of the Silicon Cover for the original E3D V6 Hotend to match China Clones is underway. A 6mm tube, equipped with 4x M2 and 4x M3 fasteners, will be utilized. For more detailed information, consult the original author. ...It's clear that a mess...

I swapped out my MPMD for e3d clones a while back (the current version is here: https://www.thingiverse.com/thing:3717404), previously I was using this one: https://www.thingiverse.com/thing:3641567. Heat creep has been the major issue I've...

3D Printing Head Clone Developed by Humans

Equipped with Dual E3D V6 extruders and auto bed leveling technology. Layer height is set to 0.2 millimeters for precise printing. Layer width is configured at 0.4 millimeters for optimal results. Infill density is optimized at 45 percent to...

E3D Clone Titan Extruder Cover Design

E3D V6 Nozzle assembly.

This is a silicone cover designed specifically for the E3D v6 clone available from Banggood, with its product page located at...

This is a silicone cover designed specifically for the E3D v6 clone obtained from Banggood (http://www.banggood.com/0_4mm-E3D-V6-All-metal-3D-Printer-Extrusion-Head-Nozzle-With-Fan-p-1036420.html?p=OF26119123132014119R) and serves as the first...

Designed this mini nozzle box for e3d nozzles.

This is a clamp for the PJRAW MK1 E3D Print Head, my clone one didn't seal properly and would spin so I had to make this clamp thicker. ... https://www.thingiverse.com/thing:4628662

e3d v6 nozzle box. Fit for 16pcs. ...Uses 3x3mm magnets.

Here is a Fan Duct for the Chinese Clone of the E3D Titan Not Sure if There are Any Measurement Differences Between the Clone and the Original One 30mm Fan Is Used for Cooling the Extruder, While One 40mm Fan Is Used to Cool the Filament The Files...

This is a silicone cover for the E3D v6 clone from Banggood (https://bit.ly/3jfFqsQ). It might fit for others too, but I did not check that. Print everything with about 20%-25% infill. You should print the parts with 0.1mm layer height for a...

E3D Revo Nozzle Holder. ... can be attached to 2020 aluminum profile

Quick blocky clamp mount for e3d v6 clones to mount to the cr-6se strain guage, probably works with cr6 max as well. --2/19/21 -- Abandoned this back in November as I'd been holding off until it was actually necessary for me to replace the oem...

This is a silicone cover for the E3D v6 clone from Banggood ( https://bit.ly/3jfFqsQ ). It might fit for others too, but I did not check that. Instructions: Print everything with about 20%-25% infill. ...You should print the parts with 0.1mm layer...

... acrylic X axis backplate. Using my mediocre TinkerCAD skills, I've created this design which allows using the original acrylic backplate while accommodating the new E3D MK6 Extruder Clones. ...It's still a work in progress, so bear with me!

Simple E3D V6 Nozzle Holder. Securely Stores 10 Nozzles, Ready for Use. ...Important Note: Mount the Top Face Down onto the Printer Bed.

I Needed a nozzle that lined up with Pheneeny's E3D v6 Direct mount. Took primativebowyer68's nozzle mirrored parts of it and then lengthened the offset. ...also added 1.5 mm to the total hight. Print Settings Printer Brand: Prusa Printer: Prusa...

... Nozzle Keychain by agepbiz (https://www.thingiverse.com/thing:4619343). Scale it to the size you want. The model was scaled up 300% in the picture above. Modelled in Fusion360 based on the drawings on https://e3d-online.dozuki.com/c/V6_nozzles

Case for E3D V6 nozzles storage. Requires 2 M2x10mm screws for the hinges. ...I included the .STEP files, so you can customize it easily.