e3d hermera

3 perimeters, 4 top/4 bottom layers, 20% gyroid fill. Run nozzle about 5C hotter than usual for better layer to layer seal. With E3D and brass nozzle, I use 255C 1st layer/other layers 260C for PETG. With SLICE Mosquito and tungsten carbide nozzle, I...

I no longer hesitate to swap to the nozzle size best suited for the task. One downside is that it doesn't have nozzle storage in its little box so hoped to improve that, with this design the holes are threaded for E3d M6 nozzle type threads, shown...

After coming up with a Diamond effector for the Anycubic Kossel Liner Plus (AKLP) I had a good think about what I really wanted from a 3D printer: i) I already have what I think is a good single-extruder design for the E3D_J6 and Volcano that's an...

### A durable and stable mount for E3D Hemera If like me you have an Ender 5 (Pro, Plus, Standard) this will be the last mount you will print. In a few months I have printed practically every single mount I have found on the web. I was so desperate...

I'll be adding a stock hot-end adapter, E3D adapter, and a mod for a 50mm blower fan soon. Advice is always appreciated, and I'd be interested in any modifications you make. Printer: Monoprice Select Mini Rafts: No Supports: No Infill: 100 ...

ST4118L1804-A with 0.5 Nm for Z ST4118D1804-A with 0.8 Nm for X/Y Z is running fine, but a little bit slow, I hope the nanotec is a little bit faster (the motor holds 0.5Nm up to 300 turns/minute) X/Y looses steps because the motors don't have enough...

The various ducts can be found at the original thing at the following link: Due to the V6 Heat sink having to move 5.5 mm forward to clear the stock mounting plate\thread inserts the previous Hydra Duct Bases and Tool Heads are not compatible.The...

Send me a message on Discord (ShadowHawk#3714) or Facebook in the group above for pricing or further info. This is a total replacement of the ProMega XY Motion System with a carriage that can mount an E3D Hemera Extruder. There is a Bill of...

all air is blown focused on nozzle tip, then gets reflected in all directions (see the video).\nThe adjustable height ensures a perfect fit for your own configuration.\nBalanced air distribution blows from two sides against each other; the air...

The firmware has my values which are for an E3D v6 hotend and a 600 watt 110 volt bed heater! All configurations using the same hardware will have different PID values due to drafts, ambient temp, etc.. GREAT 3D printing starts with good configs. If...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

* 2015-05-18 New Tool Holder Design A new tool holder and swing design were created that can accommodate a Jhead or E3D Bowden extruder with no guarantee of its success but it is definitely an improvement over the original 3mm hole design. Some...

We’ll probably make some changes such as reorienting the the y-axis linear rail into a vertical position similar to the RailCore but the current horizontal version will be easier to adapt an E3D Toolchanger. The top plates or motor/belt mounting...

Potential updates will be made in the future to adapt the E3D Revo system as they release more complete offerings. The carriage bottom has intentionally been left flat and large to facilitate easy modifying of this design for your needs.Each Y linear...

For me the temps were 230 at 30mms, due to the .8 nozzle and only having an E3D clone. I need to upgrade to a Volcano for bigger items (LOL). You will need to modify the source code for this project. It is 99.99% complete, all you need to do is enter...

i found that the carrier wobbling a little bit. i've try with 608 bearing, but metal on metal is too noisy for me. So instead of paid 80€ for proper delrin rollers. I've try to made my own with a bunch of MR83-ZZ bearings. theses rollers can be...

The new ones are a little easier to print and assemble, a little lighter, and no longer need the nozzle spacer, although I left that file here in case further tweaking is needed) This set is to provide a cooler for use with the 713maker.com Titan...

What you will need in addition to the 3 CD-Rom drives E3D V6 Hotend (or a clone) some bowden tube (around 30-40cm) a normal stepper motor for the extruder any kind of 3D printer mainboard (i used an Anet A8 - you need to modify the stepper current...

I'm running a Creality CR-10 V2 that's upgraded with an E3D Hemera, though a stock CR-10 may work just fine. The Flexihinges and bumpers should be printed in TPU with a shore hardness of roughly 95A. I used Duramic brand TPU. Other brands may be more...

Minor evolution and refinement of the 50mm design. I decided to test this design using one of the best direct drive extruders available in the 45mm world - the Bondtech MK2-MK3 (full kit) upgraded extruder made for Prusa:...

This design is a remix of his design for the H2, so a big thanks goes to him for helping me out by making some modifications to the design that I couldn't!Over the past five-ish months, I have been at work creating a design for the E3D V6 that I had,...

It's also well-balanced SturdyCompatible with the stock hotend and E3D V6 too - This design has a 3mm gap to tune the height of the fang, so it can use both. I use a V6 clone with bimetal heatbreak and it works great, my stock hotend is mounted with...

Also take a look at my other Designs!Changelog:Added a MMU version of the display coverAdded Beam with Prusa Printers logoSmall adjustments to the print filesAdded a color upgrade for the side partsAdded a symmetric version of the casingAdded an...

-  While plenty of quality 360 circular coling solutions are already published for anycubic printers, none of them have room for bltouch probe or require switching to...

Here is version 1 I am working on based on the one made by satoer's E3D V5 hotend carriage. I really like this design and hope others will be able to use it, not just on the Cobblebot but any printer using 2020 rails should be able to use it. It uses...

  --Moved from Thingiverse-- Since my Neo did benefit a lot from Thingiverse (special thanks to Kakadu for his E3D upgrade and his table stiffener, and for stueckl for his inductive Z endstop); I wanted to give something back, so here is part one of...

The No Insert version could be drilled out to suit larger tailstock spindles. Print Settings Printer Brand: Anycubic Printer: Kossel Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament: [E3D] {Ooznest} [EDGE] {PETG} [Crystal Dark]...

...Over the past five-ish months, I have been at work creating a design for the E3D V6 that I had, along with the two 4010s and the SuperPINDA. I have had constant trouble with the setup, mainly involving stringing, so I turned away from that approach.

The original is designed for an E3D V6 and Precision Piezo Orion. On the second (back)side a fan, or a probe or even a second hotend can be mounted. Next to the hypercube Evolution, you'll need: My frame was bought for a 350x350x500 mm HEVO build...

Includes mounting for dual 30mm (stock E3D) fans or single 60mm. Recommend 60x10mm fan for reduced weight and size with increased airflow. Superlite carriage now included along with the original one. Superlite carriage comes with another 25% weight...