e3d filament

I wanted to convert my E3D Titan Aero from 3mm filament to 1.75mm filament. I knew you needed a new filament guide and heat break, but I also found out you need to replace the heatsink lid because the heat breaks are not the same. I ordered a...

I wanted to convert my E3D Titan Aero from 3mm to 1.75mm filament. I knew you needed a new filament guide, and heat break, but also found out you need to replace the heatsink lid becaues the heat breaks are not the same. I ordered a fliament holder...

Update: added some cleaner filesI wanted to convert my E3D Titan Aero from 3mm to 1.75mm filament.I knew you needed a new filament guide, and heat break, but also found out you need to replace the heatsink lid becaues the heat breaks are not the...

I'll make sure to re-upload the revised design once I've fine-tuned its performance. ...And yes, it definitely functions as intended at this stage.

The push fitting isn't accurate and remains untested; it features a new Boddy containing 2.1mm tube within.

I'm always looking for something new to create for my cooling fan, so I came up with this project myself. The next step in the process was designing a casing to direct airflow towards the right spots. To achieve that, I incorporated Lawsy's vehicle...

This is a remix of the rsilvers E3D v5 filament drive. ... Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend.

This is a remix of the rsilvers E3D v5 filament drive. ... Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend.

This is a remix of the rsilvers E3D v5 filament drive. ...Provisions have been made for the PTFE tube and Bowden connector on the 1.75mm universal hotend.</p> Category: 3D Printer Parts

The E3D V6 Filament Cooler is an excellent choice for any serious 3D printing enthusiast, and with double the cooling power, you'll be able to achieve even more precise temperature control. ...This upgraded system is perfect for printing high-quality...

The original 30mm fan duct posed difficulty when removing the e3d hot end; however, this updated design makes it as simple as unlatching the stock MakerGear hot end. Files are now available for v5 and v6 hot ends, and a new easily removable bed fan...

This mount positions the CR10(s) sensor directly above the E3D Titan extruder input, significantly reducing "waste" filament at the end of a run. The sensor wire lead can be routed along the wire bundle for the thermistor, heating element, and fans,...

To reproduce this outcome: 1) Install the E3D hot end on Robo3D R1, then drill out the filament hole for extended PTFE tube extension. 2) Print this part with its large flat face downward on the bed. 3) Secure: Cut back the PTFE tube so it fits into...

The System Integrates a Cooling Unit Specifically Designed for Filament and a Separate Cooler for the Hot End.

This creation was designed using Tinkercad. ...You can make edits to it directly online at https://www.tinkercad.com/things/q9LH6pK4Tqz.

I'll email you as soon as it comes out of the printer.

The design incorporates a PTFE tube guide that feeds into Hemera Tool Slot 2, significantly shortening the filament path from the spool's rear. While it may initially seem more challenging to load due to its rear positioning, this setup offers a...

On one hand it is harder to load because it is in the back, but much easier to load because you are pushing filament through a lot less tubing with many less bends so is a net win in my opinion. ... the scad file is parametric so sholud be easy to...

Conversion Ender 3 or Cr-10 with E3D Titan Extruder and filament from above (e.g., Ikea Lack). A simple 608ZZ bearing is still needed. ... For printing, the following is required: 1x Filament Redirection Titan Extruder 1x Ring 2x Spacer The mounting...

E3D Holder with Filament Cooler for Falla3d Open Source Printer I wanted to add the E3D to my Falla3d printer while also cooling the filament. The challenge was staying within precise space limits at the front and sides of the extruder without...

When loading new filament, it's recommended to feed it into the guide underneath the holder first, which will direct the filament through a 90-degree turn and out through the right spool holder. The cap on the extruder frame can also be rotated for...

This is a mashup of 3 or more E3D v6 fan ducts I found on Thingiverse. It's still a work in progress, but it's getting there. Best printed in pure color ABS or PETG - anything else might not hold up too well under stress testing. I wanted to create...

This is an insert to replace the filament guide between the hotend and the filament gear in E3D Titan Aero to better control flexible filaments. I bought a direct drive Titan Aero to work more with flexible filaments on my railcore 2 build. This...

## Introduction Replacement Filament Guides for E3D Titan. I was having issues printing flexible filaments due to the filament getting squeezed past the hob gear and bunching up. This problem was caused by excessive clearance between the injection...

I had trouble printing TPU Material it spit out the filament on the back of the extruder So I designed this replacement Filament Guide 1.75R It is higher and tighter towards both the drive wheel and the running wheel as well as smaller hole for the...

To rectify this problem, I inserted a new filament guide between the hotend and the filament gear. This upgrade significantly improved control over flexible filaments like Ninjaflex. To achieve a seamless fit, it's essential to carefully sand or...

Fan duct filament E3D V6 50x50 5010 Prusa I3 Abbianto a | combined with: Carro porta Hot end all metal E3D V6 Prusa I3 - Carrige Follow me please for more projects ;)

Fan duct filament E3D V6 50x50 5010 Prusa I3 Abbianto a | combined with: Carro porta Hot end all metal E3D V6 Prusa I3 - Carrige https://www.thingiverse.com/thing:4227981 Guarda anche questo mio progetto Look at this my project!

I designed a custom E3D adapter mount for my Monoprice MP Select Mini 3D printer based on Brian Benchoff's original design, but I noticed that the standard heatsink and fan did not provide sufficient cooling to the filament. To improve bridging...

Filament run out sensor designed specifically to work seamlessly with E3D / Clone Titan extruders. UPDATE 3/19/2019: Made adjustments to internal dimensions, ensuring a perfect fit for the sensor, and created a slot to secure the switch on the board...