e3d clone

PTFE Tube Washer e3D Clone - A High-Quality Component for Smooth Operation

Utilizing the metallic plate accompanying the E3D clone nozzle assembly.

Remixing the E3D Clone, I'm linking it to a chain.

Screw Mount Piezo for Mounting with E3D Clone \r\nSource by DJ Demon D

REMADE COOLING DUCR FOR ANET A6 DD E3D CLONE X CAR

redesigned E3D Clone Mount to fit geeetech A10 the mount is a redesign of the Hyper Cube 3D Printer mount. ...https://www.thingiverse.com/thing:1752766/files

redesigned E3D Clone Mount to fit geeetech A10 the mount is a redesign of the Hyper Cube 3D Printer mount. ... https://www.thingiverse.com/thing:1752766/files

My e3d clone came in slightly under the original designers' specs, so I whipped up a makeshift fan duct on the fly. ...It's nothing fancy, but it should get the trick done.

Cooler for E3D v6 (Clone) and BMG Direct (Clone) with 4010 radial fan and dual 4020 blower fans.

E3D Fan Ducts Don't Sit Firmly on E3D/E3D Clone Due to Loose Fit. This Leads to Unwanted Noise from Vibrations. To Address the Issue, a Hybrid Solution is Formed by Merging the HyperCube E3D Clamp and a Fan Duct into a Single Unit. ... 09/24/17 - an...

Elevate Your Print Game with a 40 mm Fan Mount for E3D Clone (25mm Diameter) Built to Thrive on the ANet A8 No Support Needed: Printed Solo and Still Looking Sharp!

This is a reworked version of the standard Pendulum for E3D V6, specifically designed to accommodate an E3D V6 clone along with a significantly extended PTFE holder featuring larger holes.

There's only one fan duct designed specifically for the E3D V6 clone hotend.

Remastered from various sources, utilizing off-the-shelf fans designed specifically for the Ender 3, paired with an e3d-v6 clone heatsink. Employ either the right or left fan, based on personal preference. ...Minimal support structures are required.

I built this to accommodate one E3D clone, it's incredibly stable and demands minimal setup, including 2 x M3 x 20 bolts, nuts, and washers to secure it to the original carriage. ...It also requires 2 x M3 screws to hold the back in place, along with a...

I went with a cheap E3D clone to upgrade this old printer but its bowden style. ...Just need a little spacer to make it work so i designed this, simple but perfect fit with https://www.thingiverse.com/thing:3167694 this adapter notch side up so it...

My custom parts for a Chinese E3D clone to be mounted on a Hypercube X carriage. Includes a shroud for the E3D and a 40mm cooling fan. ...Sketchup files included.</p> <p>Enjoy</p> Category: 3D Printer Parts

Remake of a Thingiverse design, modified to suit an E3D Titan clone. Several interior voids were eliminated to optimize performance. ...A step file is available for download.

Remix from: Monoprice Mini Delta E3d Clone mount https://www.thingiverse.com/thing:3717404 and MPMD Double Fan Part Cooler https://www.thingiverse.com/thing:4692277 I used mount for E3D V6 clone hotend and two radial fans 40×40×10mm as part coolers.

This is a bespoke 80x80x25mm fan duct designed exclusively for the Bowden E3D V6 clone configuration on my Anet A8 printer.

I'm adding a layer fan on top of my E3D V6 clone using the stock clip adapter with its own 30 mm fan. ... If you appreciate my work and would like to contribute, your donation will go directly to the animal rescue organization ADAGA.

Part cooling for E3D V6 (clone) with Titan extruder (clone) and 5015 fan. ... Designed to use a hot melt brass insert nut.

The custom pneumatic fittings I obtained were too tiny to screw straight into my E3D Clone printer, prompting me to devise an innovative solution: installing a bracket above the extruder to securely fasten them in place. ...To facilitate easy...

Plate for mounting E3D Clone on Zonestar Z9, using the original mounting points. Mount the plate with three 4mm screws (12mm long) and a washer and nut on the backside. The Clamp requires two 2 4mm (20mm long) screws. Print in ABS plastic. ... As...

I loathe the wavy lines brought about by switching directly from a mk7 Filament Driver to an E3D Clone purchased on Amazon.com, prompting me to devise a solution and design a JHead Mount with a 10mm Holder for securing the bolted component.

... Hypercube Evolution hotend, sensor, and fan mount for the Hypercube Fusion. ...E3D Clone and M3 screws are used here solely for demonstration purposes. ... Update 04.11.18: A V2 with mounting points for fans and ducts has been added (untested).

I purchased an E3D V6 clone online through eBay, only to have the fan fail within minutes of use - you truly get what you pay for. Without a replacement fan available, I opted to utilize a 40mm fan sourced from an old graphics card instead. ...Next, I...

... Modular Carriage as Linked Remixed Part. ...Attach Your E3D and Clones Directly to the Carriage with Ease. ... This Design Features Nuts Captured at the Back for a Rock-Solid Hold on the Hot End, Ensuring Secure and Reliable Performance Throughout.

We did this for a customer with a Robo3D and found that with our E3D clone hot-ends, having removed the tube fitting, the print would fail because on retraction the PTFE (Teflon) tube lining the barrel would be pulled upwards because the tube fitting...

This is designed to accommodate the 25mm wide heat-break of aftermarket E3D Clones as the original 20mm clamp for true E3D hotends ended up breaking upon fitment.This is currently a WIP/Prototype.Fit and function are not guaranteed.ETA: Proving test...