dust collection quick connect 3d models

Magnetic dust collection connector for DW735 planer and 4" hose.Includes three models: DW735 connector, hose connector, and cap.Additional materials:6x 6x3mm N42 magnets (per model)4" dust collection hoseHose clampAll models print without supports.

Rikon 10-3061 Bandsaw dust collection shroud to help collect dust under the bandsaw table. ... This utilizes the vents on the side of the saw to provide vacuum suction.

In order to build your dust collection device, there are certain parts you will need: * Blower * 1.125 inch hose * Supply of 12 volts * A piece of birch plywood The 3D printer must be used for the construction of some critical parts such as the...

The second version used 4" Dust Collection hose, but the arms kept breaking and it seemed too bulky.\r\n\r\nMy current design optimizes airflow to pull dust directly from the area where the bit is ejecting chips. It also uses any bristles you have on...

This is an adapter for the Laguna 1412 bandsaw dust port. ...It fits over the dust port and connects to 4" schedule 40 PVC, either male or female ends. ... also searched for as Laguna 14|12

To boost the underwhelming dust collection capabilities of the Bosch PTS 10 Table Saw, I created two components. The first one gathers dust right in front of the saw blade. ...The second part directs the dust collection hose to enhance efficiency.

These files showcase the 3D printed components built into the "Compact Dust Collection Workbench" as showcased on the Shop Nation YouTube channel. Reveal Spacers set drawer front and door gaps consistently by utilizing precise measurements. Drawer...

An adaptor that allows the dust shroud 4508361 of the Makita RT0700CX2J woodworking router beeing connected to a standard 36 mm hose connector.

Adapter for the Festool OF 1010 EBQ router, connects to the rLab Unified Dust Collector system (mini connector). ... The red tape is just a marker, not a reinforcement...

I'm modifying my Tool Shop Miter Saw to connect it directly to my dust collection system, using a Rigid Shop Vac as the host for the larger end of the adapter. I've customized the design based on http://www.thingiverse.com/thing:1246651.

I just acquired a brand-new Laguna Fusion F1 table saw and needed to connect my Vacmaster - Beast Professional Series Wet/Dry Vac (VJE1412SW0201) to the dust collection port at the back of the saw. To accomplish this task, I created an adapter that...

Dust collection adapter from an incoming 100 mm hose to two 40 mm hoses. I use this on my router table to connect both the fence and the router itself to my dustcollector. Works fine with @MariusHornberger 's hose clamps. You have to print 1 x...

Dust collection adapter for the Jet 1020 drum sander. ...Converts the 4-inch outlet to a 2.5-in and redirects to the side.

I'm currently using this dust collection with my Harbor Freight Shop Vac, which is available at https://www.harborfreight.com/2-12-gal-wetdry-vacuumblower-61162.html. Please note that the diameter of this dust collection is 31.5mm and it's...

... filter onto this device. Lastly, fix the dust collection assembly's upper body in its intended location using two back-plate attached fasteners. ...Conduct all necessary electrical connections from blower unit towards the twelve-Volt power source.

- Hose Adapter Test Fit: Fits over the 2.5" dust collection hose, which is sized to slide all the way on (from the very bottom of the adapter when standing like in the photos). Because hoses are slightly tapered, scaling isn't as important - just...

Adapter to connect the dust port on a Bosch GCM12SD to a standard 2.5" hose. May fit other saws, but this is the one I have and the one I tested. It requires a fairly close fit at the saw to seal nicely and close securely on the locking tabs. I...

I Quickly designed this arm and conversion block to connect 3/4" Loc-Line to a 1.5" ID vacuum hose. ... Other hardware needed - 3x M5x16mm screws | 1x M5x8-10mm screw Loc-Line I used -...

 The magnets are a firm push fit and should not require any glue - the holes in the base of each magnet recess will allow removal if necessary for any reason, and there is room to add an extra magnet in each recess if magnetic power reduces over...

I was making a thein dust collection setup and wanted a few magnetic connectors. I wanted to be able to remove/move the trash can easily while having my harbor freight dust collector wall mounted. I used the stock harbor freight 5 inch hose for...

I recommend not running the vacuum cleaner at its highest speed, as the attachment can start to whistle due to the small diameter of the dust collection port. I also posted the part that fits into the dust collection port, allowing anyone to create...

... cyclone dust separator. ...For 2" dust collection hose.Print this part, cut opening in bucket wall for inside protrusion. ...Drill small holes and pop rivet onto bucket with silicone sealant between.I created this part with help from FreeCAD community.

Mount the TRA001 Triton router upside-down in your router table to boost dust collection. This simple tweak minimizes the open diameter, allowing for more efficient suction. The device attaches seamlessly to the standard dust cover, which can be...

Fab Lab Ioannina's Residency Program 2020 is a prime opportunity for innovation, and the CNC Dust Collection V1.3.0 project is a notable example of forward thinking in action. ...The brush plates are a crucial component of this system, designed to...

To assemble the adapter, simply remove the red composite ring from the original dust collection bag that comes with your saw and attach it to the printed component. The dimensions of the adapter match exactly the Bosch part where it fits into the...

A hose clamp that perfectly fits the shape of dust collection hoses and can be assembled without any tools. Designed for standard M5 hardware. There are four different connection pieces available to fit all hose sizes available. Just measure the...

Tired of wrestling with the 4" dust collector hose in my garage to connect it to various tools, I decided to take matters into my own hands and create a 96mm coupler that would fit like a glove on several machines. The Ridgid R45171 Table saw, which...

In order to collect the saw dust from my woodworking machines, I created a 4-way valve to easily redirect the vacuum hose from one to another machine. This to prevent to disconnecting and connecting the vacuum hose every time one switch machines. For...

Dust collection foot for a 3040 CNC Machine.PLA printed Foot with output for a SCH40 PVC Pipe. ...Uses two TPU 'combs' slightly offset w/ a PLA printed retaining ring.¼-20 or 6mm hardware compatible.

Dust collection foot for a 3040 CNC Machine.PLA printed Foot with output for a SCH40 PVC Pipe. ...Uses two TPU 'combs' slightly offset w/ a PLA printed retaining ring.¼-20 or 6mm hardware compatible.