durafly t28 3d models

Create an opening on the upper surface of the aircraft's nose for sliding out this device.

Print @ 210° nozzle / 60 Bed Edit: Use V2 with big Lipo like 500mah

Vampire enthusiasts from Hobbyking seek innovative propeller flaps, while fan drone cover designs offer an attractive upgrade opportunity for those eager to amplify their aerial models' maneuverability.

Lost the small one, and used the large one to reproduce both. ... Best printed on the side (as supplied), support material needed of course.

After wrestling with the flimsy wheel support for the second time, I've decided to fix it once and for all. So, I printed a brand new shaft support (the plastic sleeve) and crafted a robust new support using a length of 2mm diameter steel wire. While...

Pour emporter vos planeurs (LIDL ou autres) sur le dos d'un TUNDRA. Prévoir du tube (ou jonc) carbone de 4 mm et 3 mm ainsi que quelques élastiques. Aucune particularité pour l'impression des pièces en PLA. ... Bons vols à tous.....

The Parkzone Spitfire Mk5 (late) model's exhaust system is exhibited on the left-hand side (LHS) in the image; please ensure you create its mirror image for the right side while assembling. ...Note that the measurements provided are in inches, not...

Print material with extremely thin layers, each only 0.2 units thick, while simultaneously filling 100 percent of the designated space.

Remix of https://www.thingiverse.com/thing:4844369 This one is hollowed out so that it flexes slighly. I found that the other versions are a bit too stiff for the field that I fly on. Print in PETG 0.2 layers N.B. ...Mirror the files in your...

Made these to replace broken brackets on my Tundra V2 (pretty sure its a V2). Original brackets are curved and these straight but they bend into place when you tighten the screws. I had to use screws a few mm longer than the stock screws to get...

simple print with supports

Use a piece of piano wire slightly longer that the width of the door. You may need to run a drill bit through the hole so the piano wire slides smoothly You may need to trim outboard edge to get a smooth movement Insert the wire with it being...

I modified this to accommodate a TBS Unify Pro 32 HV and SMA .

This sleek, compact camera mount measures just 19x19 millimeters and is designed to seamlessly integrate into a streamlined cockpit design, replacing the traditional mount for a more aerodynamic look. ...The latest iteration, V0.5, features two...

This fits on the output shaft of a 9g servo and holds two neodymium magnets. ...

A mod to help stop the landing gear pluging out on those less than perfect landing. ...Held in with M3 nuts and bolts, best to epoxy the nuts in place.

I've engineered a fresh sand filter that outshines its predecessor by leaps and bounds.

Camera mount for 14x14 camera to attach to the rudder. No gluing is required. Just one M3 14mm bolt or 12mm for tight squese. I designed this mount for [Caddix...

I didn't want to keep GPS in the fuselage near vtx's and HD-camera's radio noises nor dig it into the tail's foam. So made this tail surface mount for Beitian's BN-220 gps module. Print upside down without supports. ...

Didn't want to touch an ugly wooden FPV-pod provided by the manufacture, so designed a better-looking pod. Thin and lightweight. Easy to print in one piece. I used a lot of the time and iterations to get this design as good as my nerves...

I'm creating this thing with Tinkercad - you can edit it online at https://www.tinkercad.com/things/2G2x7YLAlF2. This is a remixed design based on: https://www.thingiverse.com/thing:2793047. ... Compared to the original version 1 landing gear for the...

The weight on my bomb gave way right through the nose on its first drop, prompting me to make some adjustments to give it more stability. I took Tom's BF110 bomb and used the MS 3D Builder to cut off the nose section, then resized it and drilled an...

Modern Table Lamp 02 - Circle T28V-ray materials and default scanline materials included. This is a highly detailed model with real-world scale. The model has been carefully centered at the origin point, ensuring precise alignment. Each object...

This is my first shot at designing a simple part for my Hobby King Tundra R/C Airplane. I wanted a good safe place to mount my Runcam2 or Mobius camera, and I'm not interested in taking any chances with it falling off the wing. Mounting cameras on...

Printing PETG Infill 45% 1st attempt for a Durafly GOBLIN

T28 Turnip 28 soldier miniature conversion heads 5 pieces 28mm scale

The model T28 is a high-end replica of a historic tank designed by HTC for scale model enthusiasts and historians.

I designed an eye-catching case badge to adorn the front of my T28 case, infusing it with a dash of flair that elevates its otherwise bland appearance.

Here my Pan & Tilt for Durafly Skymule FPV Print Settings Printer: Malyan M150 Rafts: No Supports: Yes Infill: 20%

The Durafly BF-110 features a directional finder loop antenna for precise navigation, with the important detail that the dimensions are provided in inches rather than millimeters.