durafly micro tundra 3d models

This is a replacement float mount specifically designed for the Durafly Tundra, featuring captured nuts glued into place, and M3 machine screws instead of the self-tapping ones that come with the aircraft. To install this part, you'll need to remove...

Hobby King's Grand Tundra model features vortex generators on top of the wing, so I created these custom vortex generators for my regular Durafly Tundra. Researching Vortex Generators revealed several publications that stated the vortex should be...

This is a replacement for the landing gear mount for the Durafly Tundra, designed with captured nuts glued into the part, and M3 machine screws instead of those self-tapping ones that come with the model. The fit down the sides of the fuselage isn't...

landing gear retainers for the tundra v2 may require a little sanding...print 1 then mirror for the other side

I wanted to beef up Tundra's flimsy landing gear frame, so I conceptualized landing gear fairings that not only look sleek but also provide extra support to the landing gear itself. With these fairings in place, the landing gear can now handle even...

This mount fits perfectly into one of the holes in the bottom of a Tundra, giving you an underneath view with the landing gear right there in shot. It provides easy access to the USB port, SD card slot, and buttons. Printed in two pieces that snap...

I experienced a rough landing while on floats with my Tundra. The plastic mounts detached from the foam floats and one cracked, while another sank to the bottom of the lake. I've created a replacement based off the original design. Measured with...

Replacement strut cap can be found at https://hobbyking.com/en_US/Durafly-RC-TM-Tundra-Wing-Strut-Set.html. ...After printing, it's crucial to shape the cap using a heat gun, as shown in the attached image.

A remix of the Durafly Tundra Landing Gear Fairings by SaKes: https://www.thingiverse.com/thing:4360587 Similar in design and function to the original, adjusted the fairing geometry to sit higher/closer to the fuselage. Fairings are designed to be...

Some spats that clip on to the landing gear wires of the durafly tundra. Helps prevent the wires from bending on those less than perfect arrivals. ...Thers a top and bottom spat, easier to print than one long one, spreads the load a bit better can be...

I had a rough touchdown and snapped the gear screw cover on my Durafly Tundra V2. ...This isn't an exact replica, I'm no CAD expert, so don't expect perfection - just a quick fix that gets the job done.

Battery compartment designed specifically for Durafly Tundra RC Airplanes, featuring 20mm velcro straps for secure attachment. Easily installed using either 3mm bolts or a strong adhesive to ensure a permanent hold. ...The compact 100mm model...

A remix of the Durafly Tundra Landing Gear Fairings by SaKes: https://www.thingiverse.com/thing:4360587 Similar in design and function to the original, adjusted the fairing geometry to sit higher/closer to the fuselage. Fairings are designed to be...

This remix of the Runcam split mini mount for Durafly Tundra is designed by MystX, adapted specifically to fit the Runcam split 3 nano. To achieve this, I made some key modifications to ensure a seamless integration. Firstly, I scaled down the mount...

Remix of Tail Strut Supports for Hobby King Durafly Tundra. The flimsy strut supports included with the kit failed when gluing, causing frustration. I re-engineered the tail strut support system to eliminate the need for cutting foam or adding...

Pour emporter vos planeurs (LIDL ou autres) sur le dos d'un TUNDRA. Prévoir du tube (ou jonc) carbone de 4 mm et 3 mm ainsi que quelques élastiques. Aucune particularité pour l'impression des pièces en PLA. ... Bons vols à tous.....

Made these to replace broken brackets on my Tundra V2 (pretty sure its a V2). Original brackets are curved and these straight but they bend into place when you tighten the screws. I had to use screws a few mm longer than the stock screws to get...

Battery Holder for 3S 2200 LiPo Keeps Battery from Sliding, Retained by Clip or Velcro Strap Print in Two Pieces and Super Glue Together: You May Need to Heat the Clip Tab to Bend It into Place for a Better Fit. Print the Clip Side on Its Side so...

I really love https://www.thingiverse.com/thing:1862996, but unfortunately, they don't fit on my print bed, and I detest gluing or welding things together. This model was created from scratch in OpenSCAD to closely match workshopbob's fantastic...

Engineers created this as an alternative to replace a missing wheel nut.

I'm adding files to make some changes.

Battery holder for the Durafly Tundra has a 2200mAh Lipo battery powering the engine and another 1300mAh Lipo battery driving the FPV equipment, featuring several holes to adjust the center of gravity. To secure the batteries in place, use a rubber...

This is a remix of a great model for Runcam 2 mounting platform for Durafly Tundra V2 RC Plane. All I changed from a nominal model is extending a little bit to introduce a lip all around the part so camera does not have to be glued/taped and wont...

I use it in my Durafly Tundra V2 for my 3S 2200mAh battery. It makes it easy accessible and fixes the cog. The battery is fixed with a rubber band to the battery tray. The tray itself slides into the tray-mount, wich is glued to the airplane. The...

Thanks are due to JohnVH Photography for the awesome Tundra photos that inspired me! And remember, TEAM C/L FTW! Print Settings: * Printer Brand: Prusa * Printer: Prusa Steel * Rafts: Doesn't Matter * Supports: Doesn't Matter * Resolution: .2mm *...

This is directly derived from a genuine inspection of the FPV canopy, which is crafted from laser-cut plywood and comes packaged with this particular model. ...It's also available for purchase at HobbyKing through the following link:...

Not quite a remix but based on work done by Rob Thomson. https://www.thingiverse.com/thing:1362079 Mk1: Still a work in progress. Use SG90 servo for the tilt. There are two options for the pan servo (SG90 or TGY180). ...

perfect for crash

I tried SaKes' version of the mount and wasn't quite satisfied. So did a few changes. But thank him for the idea! Added a slope also on another side of the spar lock for better hold and no glueing required. Also moved spar lock's hole a bit...

This high-performance spinner attaches securely to any stock motor with just two tiny screws, ensuring rock-solid stability. Two precision-engineered 2mm or smaller screws firmly hold the spinner in place against the rear plate, guaranteeing smooth...