durafly micro tundra fat float wheel set by 3d models

This replacement front section for the Durafly Tundra and Tundra V2 models does not accommodate a bonnet, significantly altering your plane's appearance. Nevertheless, it serves as a functional replacement after a crash. To install, carefully cut...

I'm a remix of Durafly Tundra FPV Pod by robthomson - http://www.thingiverse.com/thing:1362079. I didn't like the original servo position. Printing Rob Thomson's FPV pod would be a nightmare, so I cut the pod in half and positioned them vertically...

I designed a straightforward wall mount for my durafly Tundra drone. ...The model itself was slightly oversized for my living space, so I attached it to the wall instead of leaving it on the floor.

This is the remix to remix :)\r\n\r\nI really liked both, original and remixed tail struts for Durafly Tundra from Hobbyking but, both were too big for me so I decided to slim them down a bit ... about 1-2g, maybe not worth it but still, they look...

This is a reworked design of the Camera Mount For Durafly Tundra, created by WiiTodded. I narrowed down the width of the mount and smoothed out its edges for a more refined look. To increase versatility, I added M3 nuts to the mount, allowing users...

Hobby King's Grand Tundra model features vortex generators on top of the wing, so I created these custom vortex generators for my regular Durafly Tundra. Researching Vortex Generators revealed several publications that stated the vortex should be...

I came up with a quick and easy print to mount my Foxeer Legend 2 camera to my Durafly Tundra using the existing mounting points for the candy dropper. Simply use the EPP adaptor plate that comes with the Tundra and some 4mm x 25mm countersunk bolts...

Durafly Tundra landing gear support.The tundra's landing gear wire is made from regular steel wire which tends to bend out of shape from time to time.This part is to use when making your own improved landing gear from spring steel wire.I used a vise...

This mount fits perfectly into one of the holes in the bottom of a Tundra, giving you an underneath view with the landing gear right there in shot. It provides easy access to the USB port, SD card slot, and buttons. Printed in two pieces that snap...

landing gear retainers for the tundra v2 may require a little sanding...print 1 then mirror for the other side

I wanted to beef up Tundra's flimsy landing gear frame, so I conceptualized landing gear fairings that not only look sleek but also provide extra support to the landing gear itself. With these fairings in place, the landing gear can now handle even...

Not quite a remix but based on work done by Rob Thomson. https://www.thingiverse.com/thing:1362079 Mk1: Still a work in progress. Use SG90 servo for the tilt. There are two options for the pan servo (SG90 or TGY180). ...

Replacement strut cap can be found at https://hobbyking.com/en_US/Durafly-RC-TM-Tundra-Wing-Strut-Set.html. ...After printing, it's crucial to shape the cap using a heat gun, as shown in the attached image.

A remix of the Durafly Tundra Landing Gear Fairings by SaKes: https://www.thingiverse.com/thing:4360587 Similar in design and function to the original, adjusted the fairing geometry to sit higher/closer to the fuselage. Fairings are designed to be...

A remix of the Durafly Tundra Landing Gear Fairings by SaKes: https://www.thingiverse.com/thing:4360587 Similar in design and function to the original, adjusted the fairing geometry to sit higher/closer to the fuselage. Fairings are designed to be...

This remix of the Runcam split mini mount for Durafly Tundra is designed by MystX, adapted specifically to fit the Runcam split 3 nano. To achieve this, I made some key modifications to ensure a seamless integration. Firstly, I scaled down the mount...

Some spats that clip on to the landing gear wires of the durafly tundra. Helps prevent the wires from bending on those less than perfect arrivals. ...Thers a top and bottom spat, easier to print than one long one, spreads the load a bit better can be...

Battery compartment designed specifically for Durafly Tundra RC Airplanes, featuring 20mm velcro straps for secure attachment. Easily installed using either 3mm bolts or a strong adhesive to ensure a permanent hold. ...The compact 100mm model...

I had a rough touchdown and snapped the gear screw cover on my Durafly Tundra V2. ...This isn't an exact replica, I'm no CAD expert, so don't expect perfection - just a quick fix that gets the job done.

Remix of Tail Strut Supports for Hobby King Durafly Tundra. The flimsy strut supports included with the kit failed when gluing, causing frustration. I re-engineered the tail strut support system to eliminate the need for cutting foam or adding...

Pour emporter vos planeurs (LIDL ou autres) sur le dos d'un TUNDRA. Prévoir du tube (ou jonc) carbone de 4 mm et 3 mm ainsi que quelques élastiques. Aucune particularité pour l'impression des pièces en PLA. ... Bons vols à tous.....

Made these to replace broken brackets on my Tundra V2 (pretty sure its a V2). Original brackets are curved and these straight but they bend into place when you tighten the screws. I had to use screws a few mm longer than the stock screws to get...

Didn't want to touch an ugly wooden FPV-pod provided by the manufacture, so designed a better-looking pod. Thin and lightweight. Easy to print in one piece. I used a lot of the time and iterations to get this design as good as my nerves...

I'm adding files to make some changes.

I use it in my Durafly Tundra V2 for my 3S 2200mAh battery. It makes it easy accessible and fixes the cog. The battery is fixed with a rubber band to the battery tray. The tray itself slides into the tray-mount, wich is glued to the airplane. The...

Battery holder for the Durafly Tundra has a 2200mAh Lipo battery powering the engine and another 1300mAh Lipo battery driving the FPV equipment, featuring several holes to adjust the center of gravity. To secure the batteries in place, use a rubber...

This is a remix of a great model for Runcam 2 mounting platform for Durafly Tundra V2 RC Plane. All I changed from a nominal model is extending a little bit to introduce a lip all around the part so camera does not have to be glued/taped and wont...

Majestic wheel of the great tundra plains.

Print Settings: * Printer Brand: Prusa * Printer: Prusa Steel * Rafts: Doesn't Matter * Supports: Doesn't Matter * Resolution: .2mm * Infill: 30% * Notes: You might need to orient the mount on your printer bed in your slicer program. I used 1.75mm...

A bicycle's large 20-inch wheel, known as a fat tire, offers enhanced stability and traction for various terrains.