dupont connectors 3d models

... not intended for printing, but rather for modeling your design. The dimensions are accurate, as far as I know. Once you have it open in OpenSCAD, adjust the numberOfPins and style settings - either male or female connector - to create your model.

============= This addition allows: - to play with the DUPONT connectors of the MMU2S more easily (there are often bad contacts there) - to retain the cover screws when opening - see the LEDs better You will need 2 square nuts and 2 screws, the same...

This is a remix from https://www.thingiverse.com/thing:4737042 I needed a peace wich could hold a 3 terminals connector

simple piece to hold Dupont connector more securely

When designing prototypes, I prefer using cables with Dupont connectors to connect Arduinos and other components together seamlessly. To achieve this, I created custom holders that can accommodate 4 to 7 Dupont connectors in a neat bundle. To...

When prototyping things, I like to use the cables with dupont connectors to join up Arduinos and other bits and pieces. I made these to hold 4 to 7 dupont connectors together in a little bundle. You'll need a well dialled in printer to print these....

Simple case two connect two DuPont connectors on each side: 2 males on one side, two females on the other. ...Designed to be able to connect and disconnect a water level sensor to a controller.

I was having problems programming an ESP8266 with test clips and having the DuPont connectors from my TTL cable fall off. I tried a couple of examples for connectors but they had issues. This one has the following features: * Fully parametric...

Printables link: https://www.printables.com/cs/model/219517-dupont-connector-lock Updates: 14.6.2022 - 6 pin versions added This is remix of https://www.thingiverse.com/thing:3686707. I added options for different number of wires. ...I also use bigger...

While rebuilding my Kossel, I needed dupont connectors. The ones I found online are fine, but a bit too thick to place side by side. So, with the help of my resin printer, I developed some. I'm still tweaking them, but these are pretty darn close. ... ...

This nifty piece will securely hold a 2x6 Dupont style connector in place, although you'll need to sacrifice two holes on either side to make it fit. As a result, you're left with an 8-pin connector that's sure to stay put. I printed mine using...

Dupont Connector - 2 pin - Full Set This is a simple dupont wire connector cover. In the photo, the dupont wires are at the top. At the bottom is a common american quarter to show size. In the middle is the connectors. Left to right, the first...

I don't have female Dupont connectors! :P It's not perfect, but it gets the job done and feedback is always welcome =D Enjoy and share your creations! ... If you found my Things helpful, treat me to a cup of coffee :) <form...

After making my own unified front panel connector by moving the separate connectors onto a 4x2 DuPont connector block, I couldn't find a way to key the connector. I think I found one place selling plastic stoppers but international shipping was crazy...

I needed a 4 pin connector to make a WLED strip connection and designed one from scratch using Dupont terminals.

You just insert separate cables (goldpin connectors) inside, put locking bar in and voila. You made yourself a working 40 pin connector and got rid of single plug cables. ...Never connect to wrong pins again :]</p><p>Print with any material, 100% infill...

* dupontHolderX1_v5 - One connector * dupontHolderX2_v5 - Two connectors * dupontHolderX4_v5 - Four connectors I wanted to keep the terminals connected since they are hanging but I have 3 and though it would be a good idea to keep 3 of them side by...

... dupontHolderX1_v5 - One connector dupontHolderX2_v5 - Two connectors dupontHolderX4_v5 - Four connectors I wanted to keep the terminals connected since they are hanging but I have 3 and though it would be a good idea to keep 3 of them side by side.

This remixes NodeMCU_V2-Bottom.stl from https://www.thingiverse.com/thing:2786523 to fit a board that I believe is a NodeMCU-32S (it's badly labelled). The board is 48mm x 26mm like a NodeMCU v2, but it has a ESP-WROOM-32S instead of an ESP8266,...

Set the Dupont connector in and release the pin or Pins. It will hold 1 to 5 pin connectors. ...

this is a system for connect safetly wemos d1 mini with dupont connector, for your project. In this way electrical connection is sure! ... upgrade 05/feb/21 post splitted version add version for Arduino mini and arduino nano

After switching my printer's wiring to Ethernet cables, terminated with Dupont connectors, I was constantly concerned about a cable wiggling loose. So I created this! Hardware: (2) M3 x 30 screws + (2) M3 hex nuts My design should work well for any...

After switching my printer's wiring to ethernet cables, terminated with Dupont connectors, I was constantly worrying about a cable wiggling loose. So.. I made this! Hardware: (2) M3x30 screws + (2) M3 hex nuts My design should work well for any...

Original Author: OxmstrOriginal Author Profile: https://www.thingiverse.com/Oxmstr/designsOriginal Design: https://www.printables.com/model/78295-dupont-connector-254mm-pin-holder-with-generatorTHIS DESIGN IS NOT ORIGINAL AND HAS BEEN MODIFIED FROM...

Slightly longer variant that I needed for my slightly longer dupont (28.2mm total) connectors, 4.2mm longer lengthwise Original Author: Oxmstr Original Author Profile: https://www.thingiverse.com/Oxmstr/designs Original Design:...

A straightforward housing for 2.54mm DuPont-style connectors. Connector measurements are 2.54×2.54×12mm. If you're experiencing difficulty due to tight fits, and using Cura software, consider adjusting horizontal expansion to -0.05mm. ... This can be...

This design utilizes female DuPont connectors bent 90 degrees in half. I recommend to bend the contacts inward more as the normal connection feels like it could be weak. I tried to design it so that the connectors would dig into the plastic, but I'm...

This design utilizes female DuPont connectors bent 90 degrees in half. I recommend to bend the contacts inward more as the normal connection feels like it could be weak. I tried to design it so that the connectors would dig into the plastic, but I'm...

this is a system for connect safetly wemos d1 mini with dupont connector, for your project. In this way electrical connection is sure! upgrade 05/feb/21 post splitted version add version for Arduino mini and arduino nano Print Settings Printer: Prusa...

Lock down that 4-wire DuPont connector firmly. ...The printer will churn out parts rapidly, possibly even omitting support structures if you add a bit of brim to the design.