dune in 3d

the ship is in 177 scale and the ship is 5ft long 7in wide and 1 foot high. This model was designed to fit on a 400x400x400 printer. The parts you'll need. For the radar parts you will need 1 X2 2 X4 Radar 3 is for WW2 and radar 4 is for...

The friction of the pin spinning in the carriage hole helped aligned the bore better, and increased the hole size a tiny amount for a little better play. - For scraping the copper with the drill bit, the pen spring was still enough to provide a nice...

The locking pin is 3mm in diameter and 1mm thick. Other designs are available and are listed below. PVC Schedule 40 Version: [Perpendicular PPC to 1/2in PVC Pipe](https://www.thingiverse.com/thing:5218331) [Perpendicular PPC to 3/4in PVC...

Looks very Stealth-ish :) When printing the lid with glass, break of the support sideways for a clean-cut.  Equipment: 2x M6x20mm screws1x 4mm, M8(1.25 pitch) pneumatic adapter (2x if you use the prusa i3...

Some droop on the bridging but it works just fine. For a loose fit, I scaled down the screw portion at 99%, but a dialed printer should work too. Post-Printing Heat set an insert into the knob, use a screw to secure it in place. ...I put some loctite...

Let me know if you are interested in variations with a 5015 blower or other modifications. ... [Ender 3...

Nameplates are little plates that can be flat or curved, made of resin, that you put in front of your miniature base. they are mostly the same height or a little more than the base, and if done well, they follow the base perfectly. The size of the...

Choose one you prefer to fit your grip style. CompensatorI mainly used the compensator to accommodate and hide the custom extended inner barrel.The barrel I used is slightly thinner in diameter than the original barrel, and so does the compensator...

I also recommend using Acetone to glue the pieces of the Stock to make it as solid as possible ** I do not glue the Stock to the MoveAdapter_Rear, I leave it as a friction fit so that it can be removed Tips The 30mm bolts should slide freely in and...

This is a storage box, in addition to my organizer, to enable 5-6 players to this great game. First, though not necessary here, check out and print a set of my organizer to this game (https://www.thingiverse.com/thing:5932452). Then print the...

You can use it internally like I have done here or anywhere you like.Next, load the filament in your extruder and you're done.Print SettingsPrinter:QIDI Tech X-MaxRafts: NoSupports: NoResolution: 0.20 mmInfill: 25% Filament:...

This design allows me to maintain some integrity for the enclosure while still making it easy to slide in or out without unplugging the flat cable. On the opposite side of the HDMI and audio ports, you'll find a 42 x 6 mm slot that fits several...

 It is remarkably powerful for something this size, it will penetrate cardboard and has a maximum range of 15 meters. This is a modular design that allows you to fit which ever Prod (bow) you like they simply slot in and you use a...

... out length to cut. Stl needs to be cut using the cut tool in slicer to for most build plates. This main spring Mcmaster 9637K17 2 Pins with this size Mcmaster 97395A454 32mmOD, 26mm ID aluminium tube. ...approximately 12 inches long.

You don't really need these because if you place something heavy on it, it stays there without falling.  If you want to print the magnetic screwdriver holder, you need to use magnets of Ø4mm x 3mm and maybe some hot glue to keep them in...

Insert the M3 inserts into the small holes in arm_coupler_endcap. 2. Slide the arm couplers onto the arms: - arm_coupler_pivot should be at the balance point of the rods. - arm_coupler_rubberband should be between the pivot and the ends of the...

The bridges reduce or eliminate the need for automatically generated supports in the center of the model. I ran some tests printing the top 1.5 cm and found that with just the inner edges of the blades to adhere to, the bridge layer prints better...

... through the process. Update: I have added a 16mm notch to allow the electrical connector of the nema 17 motor to slide onto the gantry. This provides space for a 40mm fan to be installed on the back side or a bracket to secure the motor in place.

Phoenix Mount: If you've followed Kyo's recommendation in the electronics video, you've gone with this controller board from Phoenix CNC: https://www.tindie.com/products/PhoenixCNC/phoenix-usb-cnc-controller-with-pwm-output/ I can absolutely...

Took a long time to make this, not expecting any cash in return. Just wanna give back to the community. My only requirement is that this is not sold, only for personal use. I am not sure what print settings were done as I outsourced locally and...

Remodeled almost from scratch with overhangs that are PETG-friendly, and only one section that needs support, which is now modeled in as a 0.5mm wall. This is easily removed - cut vertically until you reach the wedge, then the wall snaps off at the...

I plan to add this to my printer in the future and then create an adapted version for the X-Z upgraded Plus. It has many fan mounting spots for cooling: 4 to cool the motor at the back, 4 to cool the aluminum extruder parts, 2 to cool the Ubis...

Insert it into the four holes in the corners of the middle part and cut 2mm above the surface. Then glue the middle and top parts together.</p><h5>Axles</h5><p>Two axles need to be created. The axle consists of two printed wheels and a metal axis...

--- Optional parts --- Headphones Mount Variants * Headphones Mount A (Vertical Logo) The logo is positioned on a vertical surface so it avoids the post processing required in version B. Smaller logo, visible when the headphones are on. *...

Then I use small screw and nut to hold in place. You can see the small screw on the gray box. I also made a hole for a PG13.5 cable glad to run the cable into, cleans up the box nicely. For mounting the lid I install brass inserts into the...

 This is a a motorized base for https://www.thingiverse.com/thing:66708I remixed the base at https://www.thingiverse.com/thing:78218 to make the top part that interfaces with the gears (adding a corner that matches the base so it stays in place), and...

Please Refer Below: 1) Hose Coupling This Part Is Connected To The Middle Hose Ductwork 2) Air Divider A Super Glue Used On The Bottom Flex Plate 3) 12mm to 8mm Splitter Dividing Ribbed Hose Into Two Smaller Silicone Hoses 4) Hose Holder Optional...

This project also includes additional pieces for a battery holder, in case you would like to add the LED light.If you need any help with building this wand, just let me know. - RobertPS: If there is interest, I will make this tutorial more...

The profile of the top plate on the cubicles these are designed to fit is approx 77mm x 2.6mm , so basically a rectangle with those dimensions. These have all been tested and work as intended. There are several things posted here: Coat hook:...

With all gear cards stored in binders, this setup does not include space for gear card storage. Notably, monster name card dividers from 1.0 to 1.5 changed size. The larger 1.0 ones need to have their top 1mm trimmed off with a paper cutter so as to...