dummy claymore mine 3d models

I have mine in an enclosure and only have them printed in PETG instead of ABS or stronger. So I have experienced some issues over time with these due to the heat. I changed the slots used for mounting to the linear guide block to holes and beefed...

Mine was like 2mm too short, so I had to get a couple of JST-XH female connectors and make a new, longer cable. SHIM The shim raises the whole extruder side of the solution up a bit, to be more in level with the hotend side. Also, some people...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

- if there is a fit issue (I had to change the dimension thickness of the chassis) hot water bend these to fit but mine fit perfect Lower box and rod - No support needed - 20 minute print - free mount for the base of the box, the rod will connect to...

Mine are 25mm, for example, the Cross Country Performance kit uses 30mm thick spacers so you could modify the height in the Z-Axis in your slicer to potentially get 2.5" of lift from the tophat spacers alone. The lift given by the thickness of the...

To satisfy a broad range of applications, I made four different rim types and five different tire shapes (all interchangeable); in addition the wheel is fully scalable (proportionally and unproportionally) to fit arbitrary model sizes and styles.The...

I use a 5 minute 2-part epoxy from any hardware store (I get mine from Harbor Freight since its super cheap and works the same as any other brand). Start with gluing together the 2 middle pieces, ‘Middle Bottom’ and ‘Middle Top’. It's at this point...

Some of mine did not work anymore after these steps. Heating the contacts of the resistor solved the problem in my case.</p> <p>Insert the<em>Button Top</em>s into the<em>Front Panel</em> and mount the<em>Button Housing</em>s. Same goes for...

Tools you need: Torx T10or M2.5 Allen Key (for most of the M3 screws around the box) Torx T8or M2 Allen Key (for the side housing walls) Fine Tweezers Soldering iron (optional) 2.5mm JST crimp tool (optional) Parts you will need: 10x M3 nut 12x M3x12...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-C is approved for use within environments where flammable or combustible gases,...

They can be mounted with stock components, or with another work of mine, the "anti Z wobble" inspired by HEVORT (I put the link at the bottom of the article). The attachments are fixed to the aluminum profile of the X axis with 4 M5 12mm screws and 4...

I didn't bother installing it for mine. Brass rather than steel is a good choice to avoid scratching your camera's mount surface.</p><figure class="image"><img...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of no more...

I printed mine in PLA with 7% infill, 2 perimeters, and 0.2 mm layer height. The filament I used was scavenged from a dumpster. ## Assembly Notes In general, there's only one way for pieces to fit together, so it should be fairly intuitive how...

All other mods (uprights, tensioners, fan duckt) you can see on screen are not mine, but i can link them if there is enough interest. WARNING!!! THIS IS NOT A SIMPLE PROJECT! DISASSEMBLE YOUR PRINTER AT YOUR OWN RISK! I AM NOT RESPONSIBLE FOR...

After having a blade guard break on mine while it was in my backpack during some pretty typical traveling I figured it was time to just print up a case.The main idea behind this case is to support the drone by its corners and provide rigid top and...

But this hasn't been tested since mine is a really tight friction fit already. The hole covers are optional and are intended to be printed twice to slot into the space where the leds sit to cover them.</p> <p>Again, be advised that even though I got...

https://www.thingiverse.com/thing:4792317/files I created all of these blanks using this process in case anyone wants to make blanks of other ships, or just do a better one of mine. I didn't come up with this process, I pieced it together from...

I used a cotton facial pad and some Kapton tape for mine and it's doing fine. 6x M3x12 bolts for the barbells 6x 10mm x 1mm washers for the barbells 8x M3 nuts (2 for the hot end lock, 6 for the barbells) 2x M3x16 bolts for the hot end lock (you...

Also, I would not recommend doing this mod without also having some compatible corner braces, like mine (https://www.thingiverse.com/thing:2474583), that will transfer twisting moments on the uprights into the horizontals, because otherwise I think...

If your "normal" Nanos are like mine, I needed to install different driver for my windows but also select the (old) bootloader in the arduino IDE. The same way, i felt the USB port where you connect it to the computer must have enough "Amps" to...

Make sure these are snug; mine came out wobbly and required further reinforcement (details TBD). For each side, insert plexiglass and attach the respective bottom braces - #2, #8, #9, &amp; #16. Start from the front and rotate around; you'll need to...

I only had to adjust mine slightly so it hopefully is not a big deal, but may be worth checking before assembly. Assembly (see pics below): First install the Dupont connectors on the 2 wires attached to the LCD Voltmeters. You should leave about...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                                 

It's remained undeveloped probably because it was originally registered as a mining claim by wily old man Lyman Truckenmiller and he built seven houses on the property (without permits) and rented these out for at least 30 years. Lyman also dug...

Or just work it out without my files.Pull the pins out of the battery connector and swap them around if they need it, mine needed it, and if you get it wrong it will fry your controller. Red to the pin on the board near the +. Only you are sure you...

I am using the Asus Tinkerboard inside mine: https://www.asus.com/us/Single-Board-Computer/Tinker-Board/ Powerful board that fits where an RPi3 fits! Inside this the screen bezel is changed to hold the new LCD unit and the Pi has been moved to the...

I heat mine on a silicone cooking mat, in a toaster oven, 15 to 20 minutes (more 20 minutes), at 100 to 120 degrees Celsius (110 is good). Once the process is done, I carefully take the part out of the oven and let it cool down for an hour before...

therefore I've made it public. Print SettingsPrinter Brand: UltimakerPrinter: Ultimaker 2Rafts: YesSupports: YesResolution: 0.2Infill: 15%Notes:All parts fit within a 200x200x200 print volume, and I'm sure you can scale it larger, but probably not...

If your "normal" Nanos are like mine, I needed to install different driver for my windows but also select the (old) bootloader in the arduino IDE. The same way, i felt the USB port where you connect it to the computer must have enough "Amps" to...