dummy claymore mine 3d models

Mine has traveled a bit and remains intact, but you may want to just epoxy some wire and a bead.Should you choose to embark on the printed version:Print 2. It's labeled "left," but both sides are the same</li><li>Use a fine layer height. (As low as...

Length was chosen to match the width of the printer (mine is 438mm). K1's have a width of 335mm to 355mm depending on revision, so that's the length of extrusions for them - please measure your machine before ordering/cutting the extrusions.The...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

... if you get that far before I do and I'll update it here. Also, thanks to Tximy. Hole sizing and spacing from this design for the wheels/Eccentric nut saved me from having to fully dismantle mine. ... https://www.thingiverse.com/thing:3343882

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

&nbsp;I have mine in the front, with a USB fan in the back, but the opposite would also work fine. &nbsp;Which is best may depend on which direction you tend to feed filament. &nbsp;I don't hit any issues feeding filament under the bottom, past the...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT is approved for use within environments where flammable or combustible gases,...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-IBM-FA-3X150LED-RT is approved for use within environments where flammable or combustible...

The original effector is 6mm's thick, mine is 7. The rod end mounts are 52 mm's wide. So are my carriages. This way I don't need the spacers. This worked well for me for years, then I got the itch for dual extruders. I designed an effector that will...

…the corner pieces didn't print nicely enough for mine to perfectly assemble. (maybe that's my tuning issue, orientation, or lack of supports)--------------------everything below this line is copied from original that this is a remix of- full credit...

------------------------------------ ENGLISH ---------------------------------------------The guide was translated using google, I apologize in advance for any errorsTo conclude the set of linear guides on the X1, this time I propose some attachments...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

However, if your tripod isn't very good (mine aren't) I'd suggest setting the camera to use electronic shutter and either remotely trigger it or use the selt timer -- that will minimize misalignments due to vibration -- and also brace the tripod...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-180B is approved for use within environments where flammable or combustible...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

Mine just needed the supports to be removed and worked fine. To start, install the M3 nuts into the base, there are 10 pockets (see 1st pic) and I added a small drop of glue (clear Gorilla Glue) to each pocket, then pushed the M3 nut into the pocket...

Mine are 25mm, for example, the Cross Country Performance kit uses 30mm thick spacers so you could modify the height in the Z-Axis in your slicer to potentially get 2.5" of lift from the tophat spacers alone. <b> Rear spring spacers only and front...

I printed mine in PLA with 7% infill, 2 perimeters, and 0.2 mm layer height. The filament I used was scavenged from a dumpster.</p><p><strong>Assembly Notes</strong></p><p>In general, there's only one way for pieces to fit together, so it should be...

&nbsp;This means using a bolt of 35 mm (M4 or M3 will do) for the pivot.By the way, to access the Dremel chuck clamp you can…A) loosen the M3 corner screw on the upper_pillar_clamp and turn the Dremel roundB) take the rubber bands off and drop the...

Thanks CFox!&nbsp;This is the new file:internal-608-roller-bearing-base-adapter-for-newer-printers-1.0.stlI've you're using an older printer like mine in the pictures, print this...

And a 12 volt that moved an insane amount of air and sounded like a leaf blower. Print and assembly instructions I printed mine using PLA at .2mm. I really don't think it will matter much what you use as long as it can hold the screw threads.</p>...

... <h3>Final note</h3> <p>I would insulate the spring clips in the power track if there was any chance of shorts. Mine are mounted on wood. I haven't found a source for spring clips other than extracting them from a breadboard.

You may need to adjust the `centerColumnHeight` variable and re-build that object if your existing center column doesn't match mine. If you go this route, you'll need to lock the bottom reel to the 3D-printed central column, and lock each additional...

They can be mounted with stock components, or with another work of mine, the "anti Z wobble" inspired by HEVORT (I put the link at the bottom of the article). The attachments are fixed to the aluminum profile of the X axis with 4 M5 12mm screws and...

The rig can be used for heavy mining operations in the future too! I added some inspiration pictures that really helped me to design this IMC gantry crane. Design is uploaded in IGES (its STEP now, while that did seem to work) for the final assembly...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of two...

Unfortunately I sourced mine locally so I can't link to it. You need a minimum of 3 pieces (or one larger) with a dimension of about 40 x 50 cm each. One of these should be enough to cover all panels but I haven't tested this one in particular...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...

Dispensers for 12oz, and 16oz hold 3.5 cans per-layer plus 1.5 cans on the tongue.&nbsp;Printing and AssemblyLine&nbsp;I decided to slice mine with a 0.6mm line width even though I was printing with a 0.4 nozzle. so I could get a 1.2mm thick wall...