dummy claymore mine 3d models

Here is a listing for an assortment that I got mine from.https://www.amazon.com/dp/B07VS4823F?psc=1&ref=ppx_yo2ov_dt_b_product_detailsThe other aligner is printed but is wider not using the pipe.There is one more option if people want to drive the...

A first-party one ought to work as well. 8x screws with threads suitable for plastic, roughly 1.6 - 2mm by about 6mm long, to hold the controller mount, usb breakout, joystick mount and joystick breakout board. 6x m3 x 8-10 countersunk screws for the...

It helps here if your printer prints the holes slightly undersize (like mine does). The only fasters that MUST be the specified sizes is the M8 rod used for the axle for the bearings, and the M4 bolts that fix the mounting plates to the Logitech...

It doesn't matter which direction of LCD you'll chose but for the convenience the driver board attached to the LCD should be on the left side looking from the front of LCD (the side that you'll be looking at the rest of palmtop life) if you don't...

Plug it anything that's not plugged in, move the axis' around to see how the arm's doing, check how it looks in Octoprint (I had to flip my camera horizontally and vertically on Octoprint, and I forgot to set it up in Octolapse before I started a...

These may need to be scaled in X-Y (diameter) if your printer’s tolerances are significantly different than mine. They should fit snuggly into the holes in the spacers and dividers, but not be so tight as to break the parts. I suggest printing the...

I printed mine in Inland Red PLA+, Inland Blue PLA+, Inland Yellow PLA+, and Green PLA+. These are an easy print!</p><figure class="image image-style-align-left image_resized" style="width:22.54%;"><img...

I use a jeweller's loupe to check the finish, but if you have better eyes than mine you might not need any magnificationIf you printed the reed tongues and blowpipe on a surface more rough than the Prusa smooth build sheet, you should sand their...

22 AWG)10k linear potentiometer with shaft diameter 7mm or less (mine is an Alpha “12mm” model)Panel-mount momentary pushbutton with shaft diameter 7mm or lessNPN transistor x 1 piece (e.g. something simple like BC547, <strong>BC548</strong>,...

Update 2 (2018-02-24): I've been musing about the z&gt;160mm problem for chains that don't coil perfectly like mine (see update 1 above). I considered several approaches, but ended up with the most simple one: a fence which keeps the chain from...

Mine didn't came out great because of that, but yours can. - A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin) ## Print orientations Case...

Mine fit fine, but I did cycle it a couple dozen times in the channel before assembling it. <ul> <li>Also verify that the small notch that the spring retainer will lock into (in the door), is free of support material. </li> <li>To assemble the latch,...

and i use autohotkey as an app launcher for LeftCtrl, Alt, Win + a letter (a through j) Unzip the UltiPad.zip into your QMK folder in your build env, and modify/compile your own keymap. Let me know how you make out! Edit, added a slightly shortened...

The run-by holes under the threaded inserts are already designed larger.Take some measurements and make sure your threaded insert matched mine….meaning that it's top flange will settle into the provided void so the Cap flushes to the Base. I'm sure...

This is my Multi Material Upgrade (MMU) for the Printrbot Metal Plus inspired by the Prusa MMU. This collection of models has parts that I have remixed from: Josef Prusa (I used his MMU for a base to make mine) https://www.prusaprinters.org/...

Mine had somehow drifted over time due to loose screws, because of which I wasted some time in understanding why my X carriage didn't move freely and was wobbling a bit. After meticulously squaring the frame, the problem was resolved. **Mandatory...

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

Its fuel trailer and Inferno Gun gave the tank the name of flame thrower tank, clearing mine areas and making them safer for passage.The 3D printable Flamethrower Tank is showcased with its fearful gun in forward position. The model’s replica has all...

This is also an indication for printing these parts in an accent color (mine was orange).STL naming an meanings:[a]: accent color (means middle section of the pro version, mine was orange)x2: you have to print the part 2 times (example)IL1: parts for...

I didn't use a sealed tub for mine, and just sealed up the lid and other holes with weatherstripping tape. It has stayed quite well sealed, but naturally a proper sealed tub will work better and not require the extra sealing steps. The spool...

I have mine configured for the wheels to roll along the X-axis & the carriage rolls along the 2040 V-Slot is the Y-axis. I wanted it that way for the X-axis to be the longest. I have my maximum X Position set to 1000mm. The wheel distance could be...

I've printed mine in extrudr GreenTec Pro silver (bearing-seat-cap_mount and drag-knife_mount) and extrudr PLA NX2 white (counter-ring).&nbsp;Post Print InstructionsInstall the bearing seat capInstall the threaded inserts in the...

I have provided a 3mf project so you can see how I printed mine. You certainly don't need all these files that I've provided but maybe they help some people or maybe you give me feedback on the settings I'm using and we all learn. The Bed...

Mine was slightly, so I just glued a small piece of angle iron to the back of it to straighten it up. If you don’t do this, then your pump positions will be slightly off and propagation of errors will become an issue later 8. Insert the Oxidizer and...

What is happening, that I learned with the classic view and had not used it since the last time I installed Windows (much to my regret there is no version for Linux) and total that I had no way to put the .cuix of the view classic because I didn't...

One part of the railway was the coal (lignite) and briquette transport from nearby mines to the town to feed the steam engines mainly in cloth factories. There were about 70 of these wagons and trains could carry up to 15 to 20 wagons according the...

I use mine to stream the video from the prompter to OBS for use with live streams.You Will Need…A Raspberry Pi (if you can get one!). I used a Raspberry Pi 4, but a 3 should also work fine, and external access to the Ethernet and USB ports will still...

Also check that the ports on your speed controller are in the same order as in mine. Make the necessary adjustments, if this is not the case.</li></ul><figure class="image image_resized" style="width:75%;"><img...

I built a small cable like this for mine (you can see it at the back of the printer on the left in the pictures)I removed the stock LCD display as I don't use it with Klipper. You could potentially install it instead of one of the front right end...

I got mine from https://3dprintingcanada.com/collections/tpe/products/black-1-75mm-tpe-filament-0-5-kg (not affiliated). Video: - In action: https://youtu.be/3EBpf9YP5C4 - Showing the shock: https://youtu.be/YSYngEb9dG8 - Gearbox assembly:...