dummy claymore mine 3d models

I had to replace mine with a M3x40 SHCS, a couple of nylon M3 standoffs as spacers, with a washer on top, so the spring still provides reasonable tension. For the bed, tighten it down quite a lot, and set the Z endstop to stop the Z axis with the...

## EDIT (1): PRINTING THE FAN GUARD IN PETG ## While I've proven to myself that the clipping of the fan guard works well in PLA+, a friend of mine has tried it in PETG and found that PETG, though stronger, is too brittle. If anyone else has same...

And if someone wanted to know how mine turned out originally after all - beveled wood screws purchased from lowes held parts well when i tried my wrist once again after adjusting some minor details first though which isn’t hard since just a few...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

I printed mine out of Carbon Fiber PETG and it works well. The parts should be printed on a smooth build surface if possible, this is more important for the part cooler. Assembly There are 6 printed parts for this design: The H2 Mount to hold...

Many educational math toys cannot demonstrate more advanced mathematical concepts, so I hope prints like mine can help. Especially with the increase in online learning, this model should help students truly understand fundamental trigonometry.</p>...

I choose to mount mine below the air tank as there were already holes in the aluminum tube that I can use to route power. Depending on the battery you use and how you mount it you may need to extend both the power and balance leads to make it...

Side Wall Index - Works ONLY with the same cereal box as mine to place the Sidewall Shaft Holder at the proper height to hold all of the filament spools I have come into contact with. I am currently redesigning this and if you provide me with...

I think I changed mine to 20mm also, but I can’t remember right of hand. More information for these setting can be found by googling Marlin M600. Also, Michael of Teaching Tech has a great video on YouTube on what needs to be changed/adjusted in...

This design was inspired by Tamar at https://www.3x3custom.com/tutorials/adjustable-dowel-jig Mine has a few more features, but it will still be helpful to see her website and video that explains how this type of jig is used. I wanted to increase the...

I think I changed mine to 20mm also, but I can’t remember right of hand. More information for these setting can be found here: https://marlinfw.org/docs/gcode/M600.html Also, Michael of Teaching Tech has a great video on YouTube on what...

I put mine on E2. Alternatively, you can wire each one separately to its own endstop, which should still work. Wire them the same as your X and Y endstops, plugging into the Duet or Duex connecting the outer 2 pins of the 3. Nothing should be...

Mine are 10.75" long. I don't have a need for boards much larger than 6" square anyway, but the longer the rods, the larger the boards it can handle.&nbsp;The distance from the center point of the board grips to the steel rod is 5.75" so this can...

Assuming your first layer mushrooms like mine does, you will likely need/want to clean up the edges attached to the build plate with a deburring tool or file since some parts are designed with a fairly close fit. Most note ably the front switch...

The builds are:4 front quarters - I sliced mine at 0.15mm Quality setting, which was probably overkill for something hung on a wall and not handled or used very close-up. Roughly 4 hours per build at this quality level, so you could save some time by...

In principle, it should be printable with any 3d printer, as I printed mine with my old Anycubic, which was about to break down completely at the time (and unfortunately it printed like that). Maybe that's why the tolerances might not be right for...

IN this case, mine is the tds 210, but there are many compatible ones. There are already many models, but I didn't like any of them. They all had a big defect, they don't fit together. They stay loose, they fall off easily... Well, that's it. These...

As you can see the photos of my make I made mine with the knob in the left. It was not planed but it worked perfectly.</p><p>&nbsp;</p><p>Start by inserting the Shaft inside the box.</p><p>&nbsp;</p><p><img...

Through low or high tones that may sound like music, the Depth Diggers can be trained by the Gnomes to live in complete symbiosis with them, assisting them in mining and defending settlements.The hard chitin shells of these Zeeks can be used as armor...

I've set mine to 4 like this: `#define Z_PROBE_OFFSET_FROM_EXTRUDER 4` Yours could be 3 or 2.5mm depending on your setup, so you need to change it to 3 or 2.5. Once done, hit Save File and the Upload button in Arduino (top left corner with...

1 at the bottom (I placed mine in the key hole) and 1 at the top (by the key for the knee) should be fine as long as they are deep enough. The legs, I placed 1 drain hole in the key. Seriously, I can't stress this enough, I had cleaned and cured...

Mount your Logitech C270 Webcam to the X-Axis on a Prusa i3 MK2/MK3. The C270 is my go-to webcam for integration with OctoPrint, and this is my favourite "nozzle view" mounting system.Update April 4, 2021: Fellow PrusaPrinters user Nackweee has...

Top view error: notice the non-concentricity in the center mounting hole Front view error: mine sticks out a bit further on the ends. Future improvements: lever I can only do so much, so I settled for producing a friction version. The rear shifter I...

The major differences between my braces and their design is:mine are 7" wide whereas theirs is only 5" widethe Prusa frame is stock with the exception of increasing the hole sizes for M3 screws and adding slots and holes for the brace nut traps and...

#I have not yet finished mine so consider this subject to change. I just changed everything in fact to give it more room to move within it's own self. #Thank you! #For more information join our [Discord](https://discord.gg/SW4AhK2UsY) ...

I topped that with (salad) bowl finish, at the suggestion of a woodworker friend of mine. The curved sections of butcher block were made by tracing the curve on the wood, rough-cutting (to within about 3/16") with a jigsaw, and then following up with...

(See above for the caveat about the hex profile.)I opted to print mine lying down with the cupped end facing upwards. This way, the layer lines are oriented in the same directions as the thrust load when tightening the notestand. You will need to add...

The Soligor 28mm f2.8 that I have on mine has a rear element just over ½" in diameter and still vignettes slightly at wider apertures. Update:added version of chassis with clearance for the aperture rings of some lenses. ...If you plan to use a lens...

I printed mine in normal PLA at between 20% to 25% infill at speeds between 50 to 70. I originally printed most of the parts on my Ender's original build surface but it lost its magnet strength and curled up. This happened during a unrelated print...

I printed them flat with supports underneath as I have mine dialed in that they come off easily.The other pieces are quite straight forward. Again though, no supports on the threads themselves.Build Tips and Tricks:First, start with the pommel and...