dual z axis sync 3d models

My Z-axis are moving freely, but they always get out of sync as soon as the steppers turn off. Sometimes the print bed just starts going down all the way! After trying all the mods out there that were too complicated in my opinion, I started...

The lead screws are attached directly to the shafts on the dual-Z steppers and with just a light touch one side can slide out of sync with the other. Even disengaging and re-engaging the steppers can wind up slipping a step or two. There are two...

This is a belt tensionner to sync the Z Axiz the Mamorubot / Hieha SX4. ... You'll need : 1 x belt GT2 - 120cm 3 x bearing 608zz 2 x pully with dent, 8mm Inside to attached to the Z lead screw some screws and nuts Not the cutest part I've made, but it...

This is a remix from an Ender 5 plus Z sync indicator by bamcdo. It's minimal design. You need to mirror to fit the other side. You need to use the original pointing model from JonathanA66. The original models did not fit to me, because both they...

... ...had a 900mm gt-2 belt leftover from another build so I decided to build a z sync system with it. it attaches to the 4 screws under the bed. I also used a 6mm nutsert and melted it in for the adjustment. gear just slides onto the adjustable part.

I was badly looking for an affordable Z-sync on my cr-10s, the mod found was great but the belt was to lose, i removed the plate from my ender 3 zsync and took some measurements. This isn't the prettiest part but it work very very well. I used...

Version 2 of the Cranium device incorporates Hemi-Sync technology, allowing the left and right sides to work together seamlessly, potentially transforming your dreams into reality. ...Check out http://mechabits.co.uk, http://infinity-8.co.uk,...

I'm using 80x10x20mm blocks to roughly level the x-carriage bars on my Anycubic I3 Mega before homing and manual bed leveling, especially for machines not equipped with dual-Z endstops. I designed them so they easily join together and stay...

Due to the Ender 5 Plus's independent Z screws, they can easily get out of sync, making it a challenge to maintain proper alignment. Removing any part can cause the bed to fall and become misaligned. If you're like me and don't run auto-bed leveling...

Hardware (2) 60t 2GT pulleys 8mm bore 1000mm 2GT closed loop belt (1) M5 X 30-40MM (6) M5 X 12MM+ (3) M5 NUTS (1) M4 X 20MM (2) F624zz Bearings Mount and Slider 3 perimeters 25% honeycomb infill 6 bottom 8 top Spacers 2 perimeters 20% honeycomb...

If you choose to use Z Axis Timing Belt Mod A, you'll need to attach everything, align one pulley's set screw with the small hole on the front to tighten it, and then detach and lower the mod to access the second set screw. Once you've done that,...

A custom-designed motor mount is needed to prevent catastrophic collisions between the z-motor carriage, hot end, and extruder Bowden. ...This upgraded mounting system must accommodate both dual z-axis and single motor configurations.

Z-axis

Here is a Z stepper alignment kit I designed for the Sidewinder X1 based on the excellent design of dugacki for the Anet A8 (https://www.thingiverse.com/thing:2684692) Print 2 kits. Slide one ring on each Z screw (just on top of each motor coupler)...

Here is a Z stepper alignment kit I designed for the Sidewinder X1 based on the excellent design of dugacki for the Anet A8 (https://www.thingiverse.com/thing:2684692) Print 2 kits. Slide one ring on each Z screw (just on top of each motor coupler)...

Allows me to see if Z is homing properly without getting the indicator out. Also lets you know if one motor is loosing steps or not. Fits 8mm Lead screw. Category: 3D Printer Parts

Didn't pay much attention and ended up with a CR10 dual axis kit for my LK4 pro. ... Found this plate for lk4 PRO but didn't fit the Z axis nut in my CR10 kit, so i had to make some little sdjustments.

While installing the Z timing belt on my CR10S PRO with FattyGuyRiley's parts, I discovered that the belt he suggested, which was 2GT 760mm 380T, felt a bit loose. So, I designed this tensioner to ensure it is more reliable and consistent. ... Hardware...

Z-axis_first_draft

cnc z axis's

Upgrade your Ender 3 with a dual Z axis! This plate fits to the floating side of the Ender 3 X axis, and only requires the stock mounting hardware. This is compatible with either a regular or an anti backlash TR8 leadscrew nut. This bracket has been...

It can be seamlessly integrated into the lower front bracket of the dual z axis, using superglue or acetone if printed in ABS. The second part serves as an extension that attaches to the unused belt clip on the left side of the front z carriage,...

Parts: KLF08 Bearings: https://de.aliexpress.com/item/32793159224.html Ender 3 Rod: https://de.aliexpress.com/item/32904246004.html GT2 Timing Pulley: https://de.aliexpress.com/item/33017482340.html GT2 Belt Joining:...

other files must be downloaded from the original link by xsgroup. (https://www.thingiverse.com/thing:4571528) i thickened the plate for added rigidity. 4 perimeters, 40% infill. ...supports needed.

Remixed from [roroid](https://www.thingiverse.com/thing:4789043). ... Added a hole for the motor connector and strengthened the legs.

Minimum revisions are typically required when editing a document to ensure clarity and precision in communication. Effective minimum revisions involve careful consideration of each sentence or phrase, ensuring that it contributes directly to the...

I designed a lower bearing block to reduce vibrations while printing tall objects, ensuring smoother prints and increased accuracy.

For a top gantry mount only due to LED light under the extrusion.

For those who have upgraded their Prusa MINI to Dual Z using that mod: https://www.printables.com/model/311911-prusa-mini-dual-z-ck3d-modI made a quick system to attach the PSU (new version) to the second Z profile.A FEW POINTS:- It may not be the...

Z-axis top entry robot