dual extruder ender 5 plus 3d models

If you're installing the extruder on your Creality Ender 5 Plus, get this spacer for your filament sensor: https://amzn.to/35X7pr0. ...Be aware that you'll also need longer M3 screws (at least 25mm long).

I have upgraded my Ender 5 Plus to a Dual Extruder setup with the Chimera 2in-2out hotend, taking on several requests for files and instructions. Here is my attempt at providing some guidance. Most of these parts are modified versions of something...

The Creality Ender 5 Plus comes with a single gear extruder as standard issue, but users can opt to upgrade to a dual gear model for enhanced functionality and precision control over their filament feed. ...To prevent unnecessary wear on the PTFE tube...

This is a one-piece printed part for upgrading your Creality Ender 5 Plus 3D printer to Dual Geared Direct Extruder. Print it using supports, take time tweaking your supports, and remove them after printing. Used 0.2mm layer height, five...

This was made specifically for the Ender 5 plus with the extruder gear that DOES NOT have a set screw. The original gear comes off relatively easy if you get some WD-40 into it, let it sit, the put the motor in a vice and use a prybar (gently) to...

This was made specifically for the Ender 5 plus with the extruder gear that DOES NOT have a set screw. The original gear comes off relatively easy if you get some WD-40 into it, let it sit, the put the motor in a vice and use a prybar (gently) to...

Purchased a Winsinn Dual Gear Extruder for my Ender 5 Plus, however the filament coming out of the filament runout sensor no longer lines up properly with the filament hole into the extruder. This mount will line the filament holes up properly. ...

I designed a device to prevent self-unwinding of 3D printing filament spools, which often results in frustrating tangles and knots that can ruin prints.

I scanned in the filament sensor and created a shim so that the new dual gear extruder lines up with the filament sensor. Otherwise the filament has to make quite a turn...Which may be fine for flexible filament, but won't work with others. This...

Because the metal dual gear extruder for creality Ender 5 Plus has a different entry path for the filament then the plastic extruder, a spacer is needed.

Because the metal dual gear extruder for creality Ender 5 Plus has a different entry path for the filament then the plastic extruder, a spacer is needed. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: NoResolution: 200...

For Ender 5 Plus. Should also work on a regular Ender 5, but I don't have one to test, so no promises. A redesigned version of the Dual Gear Direct Drive Extruder Mount that includes a hookup for a cable chain. I also trimmed a bit of material from...

Dual Gear All Metal Extruder Found Online Has Filament Input Positioned Differently Than Original Plastic One. Exactly 9mm Away From Support Plate. This Discrepancy Results In Non-Alignment Of Filament Sensor Output Orifice With The Extruder's Input...

Re angled the extruder mount to allow for attachment of ender 5 plus extruder with run out sensor. ...

Ender 5 Plus extruder relocation mount to move it from the back of the printer to on top of the rear frame. I moved it up here for easier access to help with filament changes for multi-color prints. No wire extensions needed, however requires 2x...

... Thingiverse. I created two brackets. The default bracket is 3MM. I created a 4MM for extra strength, but think the 3MM (default) has been working fine for a month+. This also uses my Ender 5 Spool mount - https://www.thingiverse.com/thing:4299161

... I created two brackets. The default bracket is 3MM. I created a 4MM for extra strength, but think the 3MM (default) has been working fine for a month+. This also uses my Ender 5 Spool mount - https://www.thingiverse.com/thing:4299161

... I created two brackets. The default bracket is 3MM. I created a 4MM for extra strength, but think the 3MM (default) has been working fine for a month+. This also uses my Ender 5 Spool mount - https://www.thingiverse.com/thing:4299161

This Arm allows to place the extruder a bit over the Bed and therefore shortening the bowden tubing to around 43 cm, but measure yourself after installation, as it depends on hotend and extruder. The Arm is a bit flexible which acts as a vibration...

Ender 5 Plus filament runout sensor spacer for dual gear extruder (Redrex) upgrade

Ender 5 Plus run out sensor bracket for dual drive extruder (BMG type).Bracket places run out sensor at correct offset for use with dual drive extruder like the BMG.Adds filament guide.Link to Ender 5 Plus firmware config and cable management photos....

The Enders 5 Plus run-out sensor bracket supports dual drive extruders, specifically the BMG type. This design positions the run-out sensor at the correct offset necessary for effective use with BMG-style dual drive extruders. In addition to...

I ended up getting the Micro Swiss Dual Gear Extruder and saw that I needed to print a part in order for the filament to line up from the run out sensor on the Ender 5 plus. I couldn't find one so I had to make one. This is a very simple design...

Adapter for Creality Ender 5 Pro filament run-out sensor and upgraded dual-gear extruder: e.g. AliExpress item 33041468821.\r\n\r\nTwo versions available, compatible with either inset M3x5mm bolts or surface mount M3x8 mm bolts.\r\n\r\nDesigned from...

Spacer for use with Creality Ender 5 Pro filament run-out sensor and upgraded extruder with dual gears: e.g. www.aliexpress.com/item/33041468821.html Two versions provided, for either inset M3x5mm bolts or surface mount M3x8 mm bolts. Built using the...

... I found I needed room to cut the end of the filament off before pulling it back through the bowden tube. Rev 3:Added additional brackets that will work with the adjustable direct drive kits that work with the single and dual gear extruders.

90° Extruder Adapter vor the Ender 5 plus, with this Adapter, the Extruder is inside the Ender Frame

A simple tool for you to align the dual z axis on your Ender 5 Plus. Print 4 of these and place on the smooth rods. You can print the block in solid or without top and bottom. If you only have 1 stepper driver for dual Z and cannot preform Marlin...

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

I wanted to mount a Voron M4 Extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5 screws...