dual cs741q 3d models

If you're running dual z, both screws need to be holding weight. Turn the loose side clockwise until you feel it take on weight, but not enough to take weight off the other side. I have a 40-34 motor zip tied to the usually un driven side of x...

Here is the heater used: https://www.amazon.com/gp/product/B07573FKSG/ The zip ties are 2.5mm MAKE SURE YOUR WIRES ARE AS FLAT AS POSSIBLE AND AS CLOSE TO THE MOUNT AS POSSIBLE (there's zero space back there) Probe hole is 5mm so should fit most...

While I was waiting for the new fan to make it to Texas from the other side of the world, I looked into fan housings, and realized that some of the dual fan mods were probably beyond my capabilities (I'm a sculptor, not an engineer, which should be...

This is the second stage of my cheap and easy DIY dual-stage dust cyclone project . Click here to visit the first stage (https://www.thingiverse.com/thing:3669095). To be honest, I estimate that for a lot of use cases stage one one is "good enough"...

The Lulzbot Z-uppers are offset ever so slightly from the bottom; whether that's intentional or a mistake, I don't know for certain, but I think they were trying to 'spread the bars apart' slightly at the top to compensate for the failure of the...

You could use a 4, and I did at first for the built-in dual HDMI outputs, but I could never get Retropie to mirror the 2 screens (even though Raspian had no trouble). -- MicroSD card for the RPI. Size depends on how many and which ROMs you plan to...

These changes include: Change front panel thickness from 7mm to 8mm so that brass inserts could be added. Enlarged the front panel mounting holes to accommodate M3 brass inserts. Replaced the rectangular On/Off switch with a lighted round switch...

UPDATE: 21 March 2018 --------------------------------- I printed jolyrogr's beard version today - as indicated in his thing, it's a work in progress and needs some tweaking - however, it turned out quite well; I printed at 710% and duplicated the...

- https://www.thingiverse.com/thing:4562348 - https://www.thingiverse.com/thing:5043045 - https://www.thingiverse.com/thing:4948715 So far so good, I want to start with the needed items: Aluminum Extrusion Motedis.de or Banggood.com - Bosch Type...

2.Tool Change options including Stock Direct Drive, BMG Direct Drive, Dual Gear Direct Drive and standard Bowden. 3.Easy front face height adjustment of fans up to 6mm. 4.Wire Management\cable Tidy options. 5.Clear viewing window of nozzle whilst...

The loom and plug for the heated bed is maintained, but the loom and plug for hot end is not, due to me switching to a dual extrusion setup during this conversion. Some wires need to be extended and some need to be shortened. I would recommend...

Check if the bottom back screw isnt coming into contact with the wiring.-fan cover clips on to the protruding screws for the blower fansalso, if you want to run this in the dual fan configuration, wire the fans in parallel.Let me know if you have any...

Print Settings Printer: FlashForge Creator Dual Rafts: Yes Supports: Yes Resolution: .15mm Infill: 25% Notes: Assembly Instructions: Print the cradle "right" side first. Use a raft and extra support ("aggressive support" in MB 3.5.0) for best...

12/28/2020 Update: I added the fileRP_200411_Servo_Z_Dual_X.cfg* that has my klipper configuration using the servo for the Z-axis for reference. Z-axis servo/Stepper motor Pen Plotter mount for V-Slot I needed a pen mount for the Rolling Plotter I am...

The foam is soft enough that it shouldn't be an issue, but I'd be mindful of any large or fragile minis. Printing Dual-Color Designs I wanted to try something new (for me) for these prints, so I decided to try out a 2-color print using the procedure...

Have been working on this clock for a little while and needed an enclosure, and this one does the job very nicely (thanks to creator), and I used part of the Desktop widget clock for the screen insertion into the face (again, thank you). The original...

For the frame I used: 8x 3030 cast corner brackets 6x shouldered M12 blind joint button head 2x 390mm 3030 (Y) (tapped both sides) 2x 390mm 3030 (Y) (not tapped, for bed) 2x 530mm 3030 (X) 1x 470mm 3030 (X-over) (tapped both sides) 2x 390mm 3090 (Z)...

Print Settings Printer: CTC Bizer (Replicator Clone) Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 30 Notes: Print with 2 shells and at minimum use ABS | Roof and floor height - 1mm | Layer height - 0.2mm | 30% infill with a linear pattern...

So you can print it dual color by pausing after the layer at 2 mm is finished and swapping in the filament. And if you want a third color, you can pause it after the layer at 2.4 mm is finished and swap in the third color.</p> <p>After switching...

Motor Controller: Dual TB6612FNG from Sparkfun. A battery box is included in the design, but you can of course put the batteries inside instead as the box is a bit of extra work. I'm using NiMH cells in the battery pack and intend to make a charging...

So I added two lines at the beginning of the scad-file: // Change this to false if You don't use TMC2208 V1.0's and didn't have to rotate the stepper-motor-connectors (expecially that one for the x-axis) TMC2208V1 = true; // in case change to:...

... to the text. Attached here are the rev 5 files. I've also started playing with some dual extrusion prints of this, so far so good! ... If you find you have further design questions, please reference the attached technical specification drawing.

Dual height mounting options allow you to achieve the same nozzle height with all four hot ends options in the list above. In addition the probe holder mounts to the front plate rather than hot end mount so it doesn't get disturbed when swapping...

Designed with SketchUp, fixed with Microsoft 3D Builder, sliced with Cura and printed in PLA on my Robo3D R1+ Parts: Some kind of power supply with a 5.5mm plug A 5.5mm socket (from AliExpress "5pcs/lot High Quality Socket Female Panel Mount...

This is relatively simple on the Taz 6 because of the rear 10mm rails, and the dual 12mm rails on the X carriage - they work to stabilize the carriage even if the lead screw is decoupled through something like this design. This design should only...

*** Designed for use with: - MagBall arms - Orbiter Extruder 2.0 (for 1.75mm filament) - 2 x 4020 radial part cooling fans (WINSINN 24V dual ball bearing recommended) - 1 x 4010 axial heatbreak fan (Sunon Maglev 24V recommended) - Original Mosquito...

V3: So, when I designed the dual-chamber part of it, all I had to go on was a grainy picture from a low quality xun on Amazon. I didn't even really know what it was supposed to do exactly. That picture made it look like the narrowed part occurred...

motors, switches, and AA (dual) battery holders (on Amazon: EUDAX 15set Rectangular DC Motor Mini Electric Motor 1.5-3V 24000RPM with 9.8" Lead Wires with 2 x 1.5V AA Battery Holder Case and Motor Mounting Bracket Holder for DIY Toys) ... 70mm x 2mm...

aka Trianglelabs) • Phaetus Dragon Screw Mutant Base.stl (requires a P4 M10 PTFE fitting) • Phaetus Dragon Mutant Adapter.stl • Phaetus Dragon Mutant Adapter-hex.stl (same as above but uses hex nuts) Phaetus Dragon HF/ST (groove) • Phaetus Dragon...

I wish I could figure out how to show a video - this thing moves constantly as you print - proving the fact that there is a lot of tension in the line that should be absorbed and not transferred to the filament. [If you want a heavy seas dual rod...