dual chain 3d models

Heavy Amazon Dual Chain Walk (1 inch) Beef : beefed support, user firendly supportSup : support for confirmed userLys : lychee file for edit

Chain stay for the older dual chain stay ethirteen

Supportless version of tdogg450's Rear Ender 3 V2 Dual Chain Mount.

It uses the angled heated bed mount found here: https://www.thingiverse.com/thing:3285566 It uses the z axis mount and slim chain links found here: https://www.thingiverse.com/thing:4314829 It uses the Hot end mount found here:...

—------------------------------------------------------------------ Whats included 3 L Chain Axe Poses 3 R Chain Axe Poses 3 Leg Poses 5 Shoulders 9 Helmet Poses 3 Torso Poses 40mm base...

dual z chain mod for voron 2.4 chains i have -https://www.digikey.com.au/en/products/detail/sparkfun-electronics/ROB-13207/5814168 hole placement for them isn't perfect but close enough.

Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901

Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901

The rest of the assembly matches what's on the Inventables site, except for one difference - I moved all existing wiring (minus the router cord) and drag chain to the aft cross-bar so the spindle drive wiring and water lines will exit the left y-axis...

The original chainmount does not allow a chain to the hotend, so i made this quick "copy & paste" thingy to have a sideways mount too. The Corner of the upright chainmount is slightly rounded so the cables dont rub on that sharp edge. ... Please...

This is a remix of Ender 3 dual cable chain mount for flipped bmg extruder. ...I moved the extruder chain mount to the middle of the plate so the cable doesn't rest on top of the tension screw when the bmg extruder is rotated 180 degrees.

Modified the original Dual 5015 Chain mount (https://contrib.eva-3d.page/cable_chain/dual_5015_part_fan_cable_chain/) To fit v2 of the Dual 5015 Mod. __2021-08-31 Update__ : added a small (5mm) offset to increase the gap between the mount and the...

Modified the original Dual 5015 Chain mount (https://contrib.eva-3d.page/cable_chain/dual_5015_part_fan_cable_chain/) To fit v2 of the Dual 5015 Mod. 2021-08-31 Update : added a small (5mm) offset to increase the gap between the mount and the fan ......

In this Thingiverse creation (http://www.thingiverse.com/thing:49733), enhancements include increasing the plastic thickness to 2mm for better durability and enabling dual extrusion for distinct colored links. ...Dual printing requires a reliable...

... setup. Rear Bracket - Added a 5mm base extension to match the Top Plate, fixing the level issue caused by the cable chain not being straight. The 20x10 Cable chain can be easily purchased from numerous online retailers, including eBay and Amazon.

Charmander key chain for dual extruders, designed with precision using Microsoft 3D Creator on the powerful Flash Forge Creator Pro. Print Settings: Printer Brand is FlashForge, a trusted name in 3D printing technology. Printer Model is Creator Pro,...

The ability to close the bracelet with a pin and break it down into sections so it can be printed in two colors using a dual extruder system has been added. For closure, simply use a 3x30mm pin or even an m3x30 screw. ... The supports are only required...

I've been using an E3D-V6 Bowden setup with the X-carriage and cable chain by TNS on my Anet A8 for about half a year but wanted to upgrade the printer to dual-extrusion. I wanted to keep the cable chain! Have fun with this design! ... #### Edits...

Mature Adult Collectible Keychain Unveils Dual-Colored Masterpiece Inspired by Iconic Naruto Shippuden Anime Series

I tried to mix the following parts: https://www.thingiverse.com/thing:2920060 (Ender 3 Cable Chain by johnniewhiskey) https://www.thingiverse.com/thing:3715002 (Drag Chain by diogosantos88) https://www.thingiverse.com/thing:4346312 (Stock Ender 3...

Kakashi's prized Sharingan keychain is a highly sought-after collectible among Naruto enthusiasts, featuring Obito's unique dual-colored Sharingan eyes that shine with an otherworldly intensity. ...This stunning accessory is a must-have for any fan of...

Remix of the links in [this](https://www.thingiverse.com/thing:3769941) cable chain. Combines the female half of the "Kette klein" and "Kette groß" to allow the male end of the last link to connect to a male connector on a rear electronics case. ...

Star Wars Rebels Dual Color Keychain - A Galactic Collectible Get ready to join the Rebel Alliance and add some intergalactic flair to your keys with this awesome Star Wars Rebels Dual Color Keychain! This fantastic accessory is a must-have for any...

You'll need the following items: * 1x Tevo Tarantula * 1x CableChain_reduced_0.2 (2) v2.stl * 1x frame_bracket.stl (available at https://www.thingiverse.com/thing:2006671/files) * 14x CableChain_reduced_0.2.stl (available at...

I HAVE A DUAL METAL GEAR EXTRUDER AND CUT OUT SO IT WOULD FIT AROUND IT

Here is the spun text. ... All kudos go to Muzz64, but I simply needed a dual strut version, so I came up with this one fast. ...Big thanks to Murray for creating such incredible designs!

Original design: AresMars (cable chain) and xxricsxx (frame-printer holders/mounts). It's far from perfect, but so far it gets the job done. You'll need to print about 20 chain links - more or less depending on where you place your frame holder...

Original design: AresMars (https://www.thingiverse.com/thing:1932724) (cable chain) and xxricsxx (https://www.thingiverse.com/thing:3141936) (frame-printer holders/mounts). Its not perfect, but it works. You need to print 20 chain links (more or...

The cable chain extra nut holder is designed to work seamlessly with the cable chain found on thingiverse at http://www.thingiverse.com/thing:176819. Print Settings: Printer: K8200 Rafts: The raft setting doesn't affect this design's...

I totally reimagined the Marvin 3D Hubs to make it possible to print in dual color/material. I have successfully printed the helmet in Glow in the dark and Transparent blue, while using Gray for the body. ...You can check out my 3d Hubs account at...