dso138 case assembly 3d models

Let's Assemble the DSO138 Case Together! Check out my tutorial for all the files you need: Print Settings: Printer: Prusa I3 Rafts: Irrelevant - It Doesn't Matter! ...Supports: You Won't Need Any Resolution: We'll Opt for 0.2 mm Precision Infill...

The entire issue boils down to a basic DSO138 setup.

The case won't close properly with the DSO138 inside, and the corners don't match up either. There's not enough space left on the board to make it work. I had to modify the board by recessing a square area, lowering the connector hole, and also...

It is a customizable house for the DSO138. Behind there is even space for an on/off switch. it looks professional in my opinion. I advice to use a 0.4mm nozzle. ...Any print settings is fine for me but the switches and the buttons need to have a 100%...

Replacement end to hold a cheap encoder module with the standard acrylic DSO138 case

Remix case is required for DSO138; purchase link available here https://www.chipdip.ru/product/dso138-kit Setup your printer as follows under Print Settings, selecting Printer as: MC2

This is my dso138 mini case, 100% original, with desk support built right in and a battery embedded! It breaks down into four distinct parts: the top case, bottom case, support, and buttons. ...Check out the result for yourself by watching the video and...

DSO138 Oscilloscope Simple Case -Hardware M3 x 7mm or smaller -Snap on legs require light sanding or moderate pressure to attach Print Settings Printer: I3 Rafts: Not needed Supports: Not necessary Resolution: N/A Infill: 30-50% Notes: Print flat...

This is a case of DSO138 oscilloscope kit. https://youtu.be/UN_BFwLSDpU --------------------------------------------------------------------------------------------------------- 18 May 2018 Add These are downloadable files of Fusion360 format...

There are a lot of different cases for the DSO138 oscilloscope all of them are amazing, some are really complex while others are very simple. I designed this case by fusing two existing designes together end editing some features to make it easier to...

Replacement end to hold a cheap encoder module with the standard acrylic DSO138 case Print SettingsPrinter:Huge corexy Rafts:No Supports:Yes Resolution:0.2mm Infill:>20% 

This is a straightforward DSO138 project that demands just four 2*4mm hex bolts and a single switch.

You'll need the following to build a simple oscilloscope module on the cheap: To get started, you'll require one DSO138 module. You can easily find this online at eBay, AliExpress, or similar websites. For assembly, you'll need four M3 screws to...

Since there are plenty of cases out there, I decided to try my hand at designing something new - the Swiss Army knife style. This design has enough room to store the connection cable as well. So that your DSO 138 fits perfectly regardless of your...

Requires 4 small screws to assemble top and bottom together, using countersunk 2.2mm x 10mm screws. Upper box can be printed either way up; it's a matter of personal preference for top finish. ...Just remember to add supports if printing with top side...

If you're not fond of screws, there's also a "glue-together" version of the case available (without battery): https://www.thingiverse.com/thing:3448128 To extend the original posts, print the "stick" three times and press it firmly onto them. The...

... to print buttons. Insert the board carefully into the case (diagonally, as shown in the photo), then push it up with a thin tool and secure it in place. P.S. ...Covers for this design will be compatible with 9V or 6x AAA batteries in Version 2.

I remixed this design for the new DOS138 because the original case was too small and wouldn't fit properly, requiring me to relocate the reset button due to the larger LCD display. The new design also includes all the necessary holes: USB, 1kHz test...

This is a remix of https://www.thingiverse.com/thing:959009 i was not able to select this Thingi, so i do it here. ... I have created a version that can be orinted without any support cause it is made of two parts for the front casing.

The reset button is flush with the case to minimize user error. An on/off switch is also incorporated. Don't forget to include support for the battery compartment in your design. ...Alternatively, you could remix the compartment into a cable storage...

This is a case designed for the cheap DS0138 / DSO138 oscilloscope.

The remixed case stands for a DSO138 Oscilloscope made entirely from scratch using SolidWorks as the primary design tool. ...The source file is attached for easy access and further modifications.

I made a mount for the DSO138 in order to use it for the intellijel 7U stealth case. The mount consists of 3 parts and a bunch of M3 screws and nuts. You will have to print 2 items of part 1 and one item of part 2. ...The screws, that are needed are M3...

This is a custom-made version of the DSO138 oscilloscope case, engineered to eliminate the 9V power port and utilize USB power instead. This modification transforms the oscilloscope into an ultra-portable device that can be powered by a USB power...

Note: It appears there might be a new edition of the PCB before attempting this design, please also look at this modified version: http://www.thingiverse.com/thing:1202909 This is a case for the DSO138 digital oscilloscope. The single-channel 200kHz...

A compact enclosure is designed to cradle the JYE140 Boost Converter, a vital component of the DSO138 Oscilloscope setup.

Here is a remix/add-on of the Case for DSO138 digital oscilloscope designed by Egil, optimized for ease of use and functionality. A Simple yet Effective Two-Part Wall Mount System: This clever design allows you to utilize your oscilloscope while...

Case stands for DSO138 Oscilloscope. Two versions of front cover are available because I had used long tact switches when soldering. One version is designed for long switches and the other for default short switches. **Front cover printed with...

Official Manual: https://jyetech.com/Products/LcdScope/UserManual_138mini.pdf shows title of "DN138-12v02" and Model: 13805K - if your DSO138 does not precisely match this model it will not fit in this case. The model this thing is for does not...

Official Manual: https://jyetech.com/Products/LcdScope/UserManual_138mini.pdf shows title of "DN138-12v02" and Model: 13805K - if your DSO138 does not precisely match this model it will not fit in this case. The model this thing is for does not have...