drumstick 3d model

Simple drumstick-holder. ... Specially made for the Millenium 5A Maple Drumsticks. But it fit's every 15mm drumstick. ... Fit on a drumrack with 37.5mm tube.

A drumstick holder for two pairs of sticks securely holds a total of four sticks in place. Each stick has a diameter of approximately 14-16mm. The device attaches to a pipe with a diameter of around 22mm (7/8"), similar to a hihat or symbal stand.

A versatile drumstick holder that clips securely onto a drum without the need for screws. Its adjustable arm can be positioned at a 45-degree angle, providing optimal accessibility to the drumhead. The holder's sturdy design allows it to stay firmly...

A D6 with a Chicken Drumstick on the 6 side, and with sharp edges. This cute cartoon cow is a symbol instead of a number that normally would stand in their place. This D6 can be used in any RPG and is most commonly used in Dungeons & Dragons (DND).

A D2 with a Chicken Drumstick on the 2 side, and with sharp edges. This cute cartoon cow is a symbol instead of a number that normally would stand in their place. This D2 can be used in any RPG and is most commonly used in Dungeons & Dragons (DND).

The inner diameter of the holder cup and ring is 5 cm (2"), so it can hold 4 drumsticks (a bigger version for 6–8 drumsticks is available here). It clamps onto the tubing using M6x30 mm bolts (4 pcs in total, 35 mm length will fit too). There are two...

A versatile drumstick holder that accommodates 6-8 vertical drumsticks on a 1.5" (38.1 mm) rack tubing. The inner diameter of its cup and ring is 7 cm (2 3/4"), allowing for secure storage of multiple sticks - a smaller version designed to hold 4...

A two-part drumstick holder for vertical 1.5" drum rack tubing is designed to securely hold up to four drumsticks. The inner diameter of the holder cup and ring is 2", allowing it to accommodate multiple sticks. For larger sets, a version capable of...

i caught this one at a Rammstein concert. ...so it needed a special stand for it to display it properly.

I modified this stick holder: https://www.thingiverse.com/thing:1347205 . Now it matches my Fame DD-One Xt perfectly. ...I adjusted the holding clamps, so it accommodates one pair of 5A and 5B.

A small Pendant for drummers and music enthusiasts like me. ...Feel free to give me constructive criticism.  Advice is very much appreciated.

i caught this one at a Rammstein concert. ...so it needed a special stand for it to display it properly.

Print PLA bed 50 °Cnozzle 220 °C

You might need this screw driver to adjust better https://www.thingiverse.com/thing:2007075

No information is available about this individual.

... do anything you put your mind to.</p><p>No need for support, I did that for you. the wide base makes it easy to print with no worries about lifting or warping of the drumstick.Angled for printing large, you can scale it to whatever size you want.

The rider's trusty instrument rests on a sturdy drumstick rack attached to the Kamen Rider Hibiki gear.

The Human stands at an impressive 30cm tall, effortlessly holding four drumsticks in a direct alignment with the drum set's sturdy framework.

Creating a Simple Drumstick Holder Project: A DIY Guide This straightforward project is designed for two pairs of drumsticks, allowing them to be placed conveniently within easy reach on any part of your drum setup. I opted to mount mine directly...

... on Roland and Alesis racks as well as other racks with 38mm diameter pipes are available. ... Holders for drumsticks intended to be used on Roland and Alesis rack systems, along with other types of racks that feature 38mm diameter tubes, can be found.

Drumstick Holder for Roland MDS-4V Drum Set This innovative holder is specifically designed to securely latch onto the 38.5 by 38.5 mm square horizontal post found on Roland's MDS-4V drum set. The holder is engineered to accommodate up to 2...

I designed a drumstick holder to securely attach to a 38 mm digital drum rack. Two versions of the clamp were created, one for horizontal and the other for vertical mounting, as demonstrated in the accompanying photos. ...This innovative solution is...

I required a drumstick-holder for my 5a's on my practice-pad-stand, which lower tube is 19mm in diameter. The letters are too small depending on your nozzle-diameter and the hole-diameter came out smaller than intended... but hey - the thing works.

The drummer's go-to accessory is a cylindrical stick restorer.

People can be linked together to form a continuous sequence.

<p>I was playing around with thin films and had the idea to make a finger drum, here it is! If you have an idea of possibly trying to tune it, lemme know!</p><p>If you liked this project, you can now support me by buying me a pizza :)! ...<a...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Remixed from: https://www.thingiverse.com/thing:2747039 The original design has no bottom and doesn't work for my sticks, so this one has a bottom.

No description was provided.