drone gps mount 3d models

The mount's potential versatility could make it suitable for any quadcopter featuring 25mm between screw holes. However, I'm not entirely satisfied with the cover's sturdiness, which seems somewhat flexible. If this design proves unreliable under...

This is a mount for my Custom BetaFPV HX115LR Quad to hold a BZGNSS. BZ-121 GPS module 12mmx16mm dimensions. ... Similar to the Flywoo Nano GPS

\nEarly Magellan Roadmate GPS devices used a “T-Slot” socket to mount the device to dashboard, windshield, cup holder and other mount locations. At some point in succeeding models, the “T-Slot” was replaced with a 16mm ball mount that can accept...

GPS MOUNT: With a 41-42mm wide space, this mount is perfect for housing a 4s 2200Mah battery and holding the GPS antenna on a 20mm round platform. It weighs in at 10g with 25% infill for added strength, and comes equipped with a convenient handle...

GPS MOUNT: This design provides 41-42mm of space for a battery of up to 4s and 2200mAh, while also securely holding a GPS antenna on a 20mm round platform. The entire mount weighs in at just 10g when printed with 25% infill for added strength, and...

Ball mount for use on popular GPS 17mm ball attachments Works in PLA. Better in PLA+ . Models oriented for best printing strength. Threads are close and need to be 'exercised' a few times before becoming smooth. Two collar and mounting base options...

A simple yet effective GPS mount (Matek GPS) is designed specifically for the ImpulseRc Alien frame. The latest Version 2 has a minor raised section in the center to prevent stress on the connector, which can cause disconnection of the GPS signal.

OpenPilot's Latest Navigation Breakthrough Hits the Market with Release of GPS v9 For Those in Need of a High-Performance GPS Upgrade, the Long-Awaited OpenPilot GPS v9 Is Now Available for Immediate Purchase at:...

GPS bracket made of PETG, tested on secondary roads. ...Screws are M3.

A compact base for securely fastening your GPS receiver's antenna.

Mount to relocate GPS to battery strap (for iFlight drones)

This innovative solution worked perfectly, allowing me to easily attach my GPS unit to the car's dash by sticking a metal plate onto its back, which would then magnetically secure itself to the mount. However, upon attempting to use it for a second...

Lost my gps on the trail and designed this to be more solid than the stock mounts. I have not printed the 35mm version so not sure what size screw is needed, either a 3mm x 25 or 20. To make it grip the bar without over tightening it I made a...

Custom Section Design Considerations The GPS mast mount on the HobbyKing S-500 quadcopter is notoriously fragile, to put it mildly. Mine shattered immediately when I tipped the aircraft over, prompting me to create a sturdier alternative in DS...

... ...The distance between the bottom holes is 21mm. The diameter of the bottom holes is 3mm. Horizontal hole diameter 4mm Стойка для gps. Расстояние между нижними отверстиями 21мм. Диаметр нижних отверстий 3мм. ...Диаметр горизонтального отверстия 4мм

Remixed the original after my GPS fall of in a tree crash. My version should hold GPS better and safer. The size of the GPS is 22x20mm. Diameter of the standoff is 5mm. Distance between the centers of standoffs are 19mm. ... Distance between the...

... to install a gps BE220 into a radiomaster TX16s. ... the gps goes on the bottom with the ceramic facing out, then you put the speaker and screw it on the daughterboard. ...once assembled the gps ceramic should face out through the speaker holes.

The Lezyne GPS Bike Mount has been reworked with some tweaks to make it easier to print in 3D. I printed this mount using PETG, but you can try other filaments - just be aware that PLA might not work so well. A 50% infill is a good choice for maximum...

Needed a GPS mount for my Radiolink TS-100. Had used the original re-mixed source circular mount with double-sided tape for a while, but it came loose. Designed this one in Fusion360 and it snaps firmly into place while staying fairly...

With little support, easy to cut after printing. ... http://www.drotek.fr/shop/en/home/161-ublox-gps.html Beware : pinout is not OpenPilot standard !

I Built it Specifically for a Sky Hunter. ... Reference of GPS: https://www.aliexpress.com/item/10050018401132027.html?spm=a2g0o.product.list_7.130657.item34y9e4.1b9c9f41BdWpRq

... the threaded rod and knobs in hand. Position this mounting bracket over the motorcycle handlebars, tightening clamps until it is snug against the bike. Note: I attached my GPS device using velcro to securely hold it in place on the mount's surface.

This is a simple GPS holder for the HERE 2 GPS. It may fit the Here 3 as well, but i haven't tested it. ...If you are using overly-large batteries, you may need to print a larger tower part, but this should fit up to a 3500mah 4S underneath it.

... cutout as the ideal location. ...The design consisted of two separate components, which I carefully inserted the GPS pole into the foam, positioning it approximately a half inch deep. ...Next, I applied a strong hot glue to secure everything in place.

With minimal backing, it's straightforward to sever the connection once printed. ... http://www.drotek.fr/shop/en/home/161-ublox-gps.html Be cautious: the pin layout does not adhere to the OpenPilot protocol!

This upgraded version of the Garmin GPS Circular Back Clip boasts increased durability, crafted with ABS material instead of PLA to withstand extreme temperatures within the vehicle's interior.

I Printed it with the Photon Zero, but you can print it also with a FDM Printer It is for the Beitan 220 GPS Module an fits on the most Frames

... inserted into the sturdy holder. ------------------------- GPS Antenna Holder for the Align M480 or M690 Attaches Securely with Double-Sided Adhesive Tape to Original Location. ... Standard 4mm Carbon Rod Can Be Easily Inserted into Sturdy Holder.

Two-piece lightweight GPS case for Pitlab AP GPS module now comes together with ease. Secure the base firmly by gluing it down, and then attach the top cover using 3mm plastic screws readily available at Hobbyking:...

Green hornet and bumblee be drone antenna and GPS mount. ...allows you to add iflight GPS module to drone