driver bit organizer 3d models

... layers. So far it's survived being dropped on concrete from chest height. Version 2.1 gives a slightly looser fitment, and wider holes for gripping the bit driver, so if the original 2.0 version was too difficult to use, this should be better.

... out. I've included a photo comparison of other specialty screwdriver handles found on Thingiverse for reference. Tiny Hex bit Driver: https://www.thingiverse.com/thing:3590067 Short Screwdriver Handle: https://www.thingiverse.com/thing:3838532

I extended it, adding width to accommodate the 38" wide belt clip on a Bosch drill and driver set I have.I also added space between each bit slot to increase rigidity and allow for bit holders to go in these instead of just bits also made the edges...

... without the top cover. Four M3 nuts are necessary to secure the bottom piece. Supports are a must during printing. I utilized this specific PCB model for my project: https://www.amazon.com/16-Channel-12-bit-Servo-Driver-Interface/dp/B00EIB0U7A

Easy to print and no support needed !This is specifically for the RYOBI Impact Driver (R18ID2) and drill (R18PDBL).I printed an old version(see pictures) and I'll upload the new pictures of the models I shared when I have the time to reprint it.Hope...

This is a Bauer 20V Cordless Drill Driver Dual Bit Holder that fits neatly into the notch where the belt holder resides, requiring no additional screws to secure it in place. It effectively holds two bits simultaneously. The holes are strategically...

... just falling out. I included a photo comparison of some other specialty screwdriver handles I found on Thingiverse. Tiny Hex bit Driver https://www.thingiverse.com/thing:3590067 Short Screwdriver Handle https://www.thingiverse.com/thing:3838532

Created to prevent damaging plastic caps. ... Both versions 1/4' Hex driver, 1/4' square driver can be used with 17mm spanner. ...

This small bit holder goes on the unused right mounting point. Print Settings Printer: Prusa mini Rafts: No Supports: Yes Resolution: 0.16 Infill: 15% Filament: Prusament PETG White Notes: Printed with Prusament PETG filament How I Designed This...

It keeps the bit from just falling out. I included a photo comparison of some other specialty screwdriver handles I found on Thingiverse. Tiny Hex bit Driver https://www.thingiverse.com/thing:3590067 Short Screwdriver Handle...

Use caseThis screw driver (bit holder) is made for fine to medium duty work. It is made to fit well into the palm of your hand, while still giving you a good grip for your fingers to apply some reasonable torque. Thanks to the clamping lock...

If your drill or driver sports a trapezoid-shaped indentation at the rear, this tweaked Rear Bit Holder should seamlessly integrate into your workflow. ...Thank you for taking the time to peruse this post, and I wish you a productive printing...

With the magnet inside, it lifts the bit just enough so the lip doesn't engage (its no longer needed if there's a magnet) and there's still plenty of space for the bit to sit inside.PrintingPrinted on the X1-C with Bambu PLA-CF in default settings...

This is a holder/bit organizer for Fix It Sticks hex bit holders. You can use a single part or pair. The cross bit holds the sticks and organizer together. The magnets hold the bits. The Fix It Sticks are available on Amazon. ...The 6 mm diameter by 3...

It's intended to carry 21 X 4mm driver bits, one Micro SD card, and a Micro USB Wi-Fi adapter or mouse receiver. The base houses five X 10mmX2mm rare earth neodymium magnets. These are all the tools I use on every job alongside my Cybertool. I've...

This is a Dremel Bit Organizer for tool cabinets. I wanted something that fit in a lower profile drawer so the best way is to angle the Dremel Bits. ...Now I am NOT forces to use a taller drawer.

I designed this hex bit holder as none were quite how I wanted them. This organizer holds a total 12 Hex-Bits.I also designed a 1x2 Gridfinity 32 Hex-bit Holder that can be found here! Has holes for magnets and can be stacked on top of other...

This Dremel bit organizer features multiple slots and compartments, accommodating various sizes and types of bits, making it an essential addition to any workshop.Key features:Compact Design: Saves space on your workbench while providing ample...

This is intended for tiny 4mm 5/32 inch hex drive bit storage.

This is an authentic #2 Phillips Screw Bit, identical to those found at hardware stores.

I created modular screw bit organizer blocks because I couldn't find any universal screw bit organizers that fit perfectly in my drawer. ...After just 15 minutes of modeling, I designed and printed snap action blocks overnight to solve the problem.

... quick fix in under an hour, fed up with constantly misplacing small items in my pockets or scrambling to find them when I needed them. ...It neatly attaches the Ryobi ONE+ P251 Hammer Drill/Driver right into the extra handle slot on the tool itself.

This is designed for the MLW2553-20 M12 Fuel 1/4" Hex Impact Driver, but may fit other models as well. ... You will need: -(1) M2.5 x 8 screw -(3) 5/16 diameter x 1/8 inch magnets which can be found here:...

... to fit my 0.25 inch drive bits. ... I used bits from a box of DeWalt screwdiver bits I have had since forever. They area about one inch long, so the tool cap needed to be extended to accept these as well. ... It is relatively easy to do in TinkerCAD.

This model houses the drill and stores 52 hex bits along with 2 larger holes for screw drivers and other items. I didn't like having to run out to the shop to get my drill all the time so I got a cheap one to keep in the office. Definably worth it to...

This bit holder was designed for the DeWalt 20v line of tools.  I have tested it with DCF887, DCD791 & DCD996.  The bits fit in quite snug and are held in with a bump that engages with the locking ring on the bits.  Print as is for the right side...

- Print in "tall position" with no supports - It is recommended to print the fit test first, it should fit nicely with tiny bit of force on to the bit, not too loose or too tight - Scale the whole accordingly, I printed mine out of PETG, and 0.45mm...

For this specific design, the settings were adjusted to include a center radius of 7, 7 bits, a height of 40mm, a bit-to-face distance of 6.8, two magnets with heights of 2mm each, a bit height of 11mm, a second height of 20mm and walls of 4...

My only two gripes are how tricky it is to take off the bits, which I suppose is both a useful feature and a design flaw, and how easily I lose the bits when they're not in use. This simple fix should help with the latter of my two complaints. ... The...

<p>There are 2 files here, one for the 12V tool and one for the 20V tool. ...Both hold 3 hex bits. Printed on Prusa MK3 with PLA. ...No supports needed.&nbsp;</p>