driver bit organizer 3d models

I designed this for attaching/removing camera quick-release plates. Keep it on a lanyard round my neck rather than searching through a camera bag or pockets for a bulkier screwdriver. ... Or you could tie it to a tripod leg, etc.

Follow me on:► Youtube Channel: https://www.youtube.com/SolidworksTutorialHP?sub_confirmation=1► Fanpage: https://www.facebook.com/groups/SolidworksTutorials/► GrabCad: Mr Hieu Phuong

This drill bit organizer easily slips into standard DeWALT drill bit and driver cases. The box stores a multitude of driver bits, extra drill bits, and many other compact accessories with ease. The lid also accommodates additional bits for...

CAPABLE OF HOLDING 225 BITS I had been searching for a slim bin that could hold a ton of my little bits. I couldn't find any other than Simhopp's but I needed it to fit in my packout, so after quite a bit of work, I present this. I haven't...

x 1/8" thick magnets (https://www.kjmagnetics.com/proddetail.asp?prod=D22)May require supports for the hingesScrew bits purchased from Mcmaster (2 mm linked, other ones can be found below the item in the link -...

I wanted to be able to hold more than one hex bit on the side of my impact driver at a time, so I made a double barrel bit holder. I used the same M3x10 screw as recommended in the original make to fasten it to the driver. ...It securely holds my 2"...

This model organizes the Leatherman bit kit and ratchet driver so that you can carry it in your pocket easily.It is a single file. I printed mine in Prusament PC blend with carbon fiber filament on a Prusa i3 mk3s+. Both bit kit cards need to be...

... Vinci Mini 3D printer. For an alternative bit-holding solution, consider my rear-mount bit holder: https://www.thingiverse.com/thing:2553565 Please note that this design does not fit well on Ryobi's P238 brushless impact driver due to a tight fit.

I wanted to be able to hold more than one hex bit on the side of my impact driver at a time, so I made a double barrel bit holder. I used the same M3x10 screw as recommended in the original make to fasten it to the driver. ...It securely holds my 2"...

I wanted to be able to hold more than one hex bit on the side of my impact driver at a time, so I made a double barrel bit holder. I used the same M3x10 screw as recommended in the original make to fasten it to the driver. ...It securely holds my 2"...

Designed for the small eyeglass driver that comes in the Leatherman Wave and Leatherman bit kit set. I made the center hole quite a bit smaller so the bit can be pressed in. Also pictured is my flat bit handle for Leatherman's bit extender.

This is a magnetic bit holder for a Harbor Freight Bauer 20V drill or driver. It uses two 8x2mm round magnets that you must glue in. ...The holder has two 15mm deep hex slots for shorter bits and can hold a long bit or drill bit on the outside.

Rear Bit Holder for Ryobi One+ 18V Impact Driver and Drill This bit holder clips onto the back of the lower handle area on your Ryobi One+ 18V impact driver. Normally, you would find a lanyard or wrist strap here, but it's not included with most...

This driver has belt clip mounting points on both sides and the clip is normally on the left side. ...This small bit holder goes on the unused right mounting point.

Team Black Sheep All-purpose 24 Bit Driver Kit case holder for IKEA SkadisTBS bit driver kit has a well designed case which is handy for quad-based projects. This mount allows for easy storage and access on an IKEA Skadis. Print SettingsMost print...

Team Black Sheep All-purpose 24 Bit Driver Kit case holder for IKEA SkadisTBS bit driver kit has a well designed case which is handy for quad-based projects. This mount allows for easy storage and access on an IKEA Skadis. Print SettingsMost print...

This is not really a remix, I just wanted to get this labelled so that anyone looking for a drill bit holder for their Porter Cable PCC647 20v Brushless Impact Driver would find it.This is UNmodifed from Inspectorgadget's Milwaukee drill driver bit...

The "open" has no bit retaining block so you can put odd-sized bits in the bit storage such as nut driver bits. The "solid" is the same as the "storage" except the bit retaining block is solid so you do not have to deal with magnets for the lid. ...

This bit holder mounts to the standard pattern on DeWalt drivers. Everyone's 3D printer prints at a slightly different size, so you might need to do the following fix if the bits don't stay in securely. --You may need to get a lighter and hold it...

This is a remix of ucancallmebob89's bit holder for the Dewalt 20V drill and driver. I couldn't use it with my 3AH battery. I trimmed it down to hold (2) bits instead of (4) and it fits great! It works with the 1AH, 3AH and 4AH 20V batteries. I...

Slight modifications to fit the newer impact driver, model 3453 (slight change in screw hole size and location, new model uses a 6-32 screw, chamfered edge to clear new driver body shape, removed stepped edge along the bottom), also added recesses to...

A holder for your screw driver bits. A problem with other bit holders are that the bits are often spaced to close together and too close to the back wall, which can make it difficult to grab a particular bit quickly.This design spaces the bits apart...

Shelf for keeping the Large drill bits and Dremel bits organized and out of the way.

This is a snap-on bit holder for the Wurth (Bosch rebranded) 12v impact driver. ...Since this model doesn't have any screws in the back normally used for a belt clip, I made a snap-on version that fits snugly in the rearmost motor vent.

Essentially a “shoe" that adapts your existing Mako Driver 64-bit kit to Gridfinity.  It made more sense to me to keep using the existing layout than design a new thing from scratch. ... You can leave the lid on, but I prefer to stick that to the side...

I designed a bit holder for the vonroc drill and impact driver because I couldn't find one. You will still need to use a screw or glue to mount it. If you have adhesion issues, you can use the “adhesion” file. That one prints a layer below the model....

This is a thumb driver for a ¼ hex bit. But I took the original design and added a slot for a 3x6 magnet. Here's the link for the magnets I used, https://www.amazon.com/gp/product/B0C2YR6WMW/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 . ...Its...

Easy to print and no support needed !This is specifically for the RYOBI Impact Driver (R18ID2) and drill (R18PDBL).I printed an old version(see pictures) and I'll upload the new pictures of the models I shared when I have the time to reprint it.Hope...

the bit slots are oversized and the bits spin in their slots (not really much of a problem actually it but wasn't intended) the big hole was intended to be able to stick the handle of the driver into to hold the driver upright while using it at your...