drip line plugs 3d models

Human: Version 2 of the Drip Emitter is designed to efficiently drain excess water from pots with a hole at the bottom. Simply snap it into place, and the Emitter fits snugly inside the hole. For an added layer of security, users can apply silicone...

Version 2 of the Drip Emitter fits neatly inside pots with a hole at the bottom, draining excess water as needed. Simply snap it into place for a secure fit - adding silicone around the edges provides an extra seal. Next, attach a long piece of...

Version 2 of the Drip Emitter provides a simple solution to draining excess water from pots that have a hole at the bottom. It fits securely inside the hole - all you have to do is snap it into place. For an added secure seal, use silicone around the...

Version 2 of the Drip Emitter is specifically designed to drain excess water from pots that have a hole at the bottom, providing an easy solution for those who need it most. It slips snugly into place with just one simple snap - all you have to do is...

So I created this cover/straightener, pretty much like a hexagonal drinking straw, that slides over the drip irrigation line to keep it straight (and also protected from damage such as solar UV and shovel nicks). I used a pentagonal design which...

This is a cover I designed for running two drip irrigation lines neatly in parallel. The bottom is open so the tubing can be pressed into the completed cover without disconnecting any irrigation lines. Default dimensions are for 0.245" OD tubing...

Easy-to-use irrigation clips for securing .700" (OD) and .250" (OD) drip irrigation lines. ...Simply attach the clip to the line and press into soil to secure.Note: clips are sized to nominal dimensions, you may need to scale up or down slightly to get...

This is a custom-designed drip line stake, paying homage to the innovative work of Bocklar and tinkering enthusiasts everywhere. Created with precision using Autodesk 123d Design software, this unique stake boasts a sleek and functional design. ...On...

Easy-to-use irrigation clamps for securing 0.700" (OD) and 0.250" (OD) drip irrigation lines are available. Simply attach the clamp to the line and press it into soil to secure tightly. ... Note: Clamps are sized to nominal dimensions, so you may need...

I needed a way to get my hanging baskets disconnected from my drip lines when storms approached or to change them out without removing the lines and stakes and destroying the plants. These are simple twist on - twist off couplers that connect to drip...

I needed a way to get my hanging baskets disconnected from my drip lines when storms approached or to change them out without removing the lines and stakes and destroying the plants. These are simple twist on - twist off couplers that connect to drip...

I needed a way to get my hanging baskets disconnected from my drip lines when storms approached or to change them out without removing the lines and stakes and destroying the plants. These are simple twist on - twist off couplers that connect to drip...

screw hole plugs in differend depths and sizes 4_1 = 4 mm hole diameter with 1,3 mm depth 4_2 = 4 mm hole diameter with 4,5 mm depth 4_3 = 4 mm hole diameter with 7,3 mm depth 4_4 = 4 mm hole diameter with 10 mm depth 6_1 = 6 mm hole diameter with...

I required a plant spike-type dripper that disperses nutrient solution beneath the surface yet close to the top. This functions with approximately 0.170 ID tubing, measuring about three inches in length, and features holes through both sides. ...The...

vape drip holder

Human: Version 1 of the Drip Emitter is used in conjunction with pots that have a hole at the bottom, which allows for excess water to drain out of the pot and channel it into a reservoir through a piece of tubing attached to the Bolt. To set up the...

Human users who prefer to keep their plant pots from becoming too waterlogged are able to successfully do so thanks to Version 2 of the Drip Emitter. Designed specifically with holes at the bottom, it snugly fits right inside by simply being snapped...

Human Version 2 of the Drip Emitter makes draining excess water from pots with a hole at the bottom possible, allowing you to redirect that water into a reservoir through a tube attached to the Bolt. To install, begin by emptying your pot and then...

The latest iteration of the Drip Emitter, Version 3, boasts a series of notable upgrades over its predecessor V2. This enhanced design is specifically engineered to drain excess water efficiently from pots that feature a hole at the bottom. The...

Also take a look on: Seedling greenhouse from Ikea Trofast (https://www.thingiverse.com/thing:4848209) Micro drip line (4.6mm) holder on the wall (https://www.thingiverse.com/thing:4851701) Vertical holder for Gardena micro drip line, 4.6mm...

Also take a look on: [Seedling greenhouse from Ikea Trofast](https://www.thingiverse.com/thing:4848209) [Micro drip line (4.6mm) holder on the wall](https://www.thingiverse.com/thing:4851701) [Vertical holder for Gardena micro drip line,...

Also take a look on: [Ikea Trofast mount for 4.6mm micro drip line](https://www.thingiverse.com/thing:4851700) [Seedling greenhouse from Ikea Trofast](https://www.thingiverse.com/thing:4848209) [Vertical holder for Gardena micro drip line,...

Also take a look on: Ikea Trofast mount for 4.6mm micro drip line (https://www.thingiverse.com/thing:4851700) Seedling greenhouse from Ikea Trofast (https://www.thingiverse.com/thing:4848209) Vertical holder for Gardena micro drip line, 4.6mm...

In-Line type drip emitter with 3 Configurations1- Original2- Chamfer 0.3mm3- Fillet 0.3mmthe CAD files are to support the member "abcd 720643" https://grabcad.com/groups/freelancers/discussions/sir-can-anybody-tell-how-to-make-this-design

Clamp for 1/2 inch main line used for drip irrigation. Use a nail to affix to wood. I created and printed a bunch of these since I did not order enough of these. I used long nails I got from Harbor Freight. These have held up pretty well for...

This is a thinner version of my previous 1/2 inch poly main line holder. This is designed to work with #16 wire nails. I used #16 x 1 1/2 inch nails to attach the 1/2 poly mainline to the underside of our deck. I printed using PLA at 40% infill,...

Often called "oops" plug, this drip irrigation plug is to terminate the 1/4 inch drip lines, or potentially plug a hole in the 5/8's line where you made a mistake.

Relocating Drip System Lines Requires Filling In the Hole

You can fill the gaps left after extracting 1/4-inch fittings or emitters from your poly drip line by utilizing a connector that matches the mainline tube's size, typically ranging from 1/2-inch to 1-inch.

... When printing, you'll find that they fit snugly into standard 1/2-inch or 5/8-inch drip irrigation tubing with pre-punched holes - common US sizes. With just a bit of elbow grease, these plugs slide easily into place and hold firm against pressure.