drill bit index 3d models

I found that the original gopro mount was a little tight so I spaced out the hinge area a little bit. So far they fit well into every gopro mount I have tried, including the store bought ones. Here is a short video: https://youtu.be/ge3tVdlT7Fg I...

People ask me why the detail is so prominent (not just the Bimbo bits) but the muscle tone, anatomy, clothing etc. on my models . . well as they are primarily made/designed for my own collection I always sand down with fine emery then have models...

People ask me why the detail is so prominent (not just the Anatomy bits) but the muscle tone, anatomy, clothing etc. on my models . . well as they are primarily made/designed for my own collection I always sand down with fine emery then have models...

People ask me why the detail is so prominent (not just the Anatomy bits) but the muscle tone, anatomy, clothing etc. on my models . . well as they are primarily made/designed for my own collection I always sand down with fine emery then have models...

This is a heavily "in progress" project that I'm publishing now because I've made a decision to go forward with another project, and it would be a bit sad to have this project just laying around so I figured better publish it so that someone can...

For the catches and hinge assembly I used Taulman3d Alloy 910 to give me lots of strength and a bit of flexibility. I've also printed these in both PLA and ABS for all parts with no issues. Install the hub into the bottom base - it should click into...

Edit: 25/4/2018 - added a bit of tolerance (0.4 mm) to the screw holes so that they're easier to use. You can change TOLERANCE and SCREW_DIAMETER in the scad file if you want to adjust things. I did some actual measurements using an app on my phone...

I made slotted holes because my printed X mounts changed the dimensions a bit. I have printed, installed and now used this part. Below are instructions on how to set it up. I printed them with 1.8mm wall and 30% fill. I also made a set at 1.2mm...

Holes available for the MMU Cable as well.all parts are 3d printable, including the bearing shafts and t-slot nuts.Sides are ribbed vertically, which aside from aesthetics, seem to aid in the printing by reducing a bit of infill time.Thread forming...

The second member of the Strange Animals family is the punk goldfish (aka Finley).The size is 15x15 cm but still it will take a couple of hours to print…hope you like it :)(i've darken the tone a bit before release, so expect it to be a little more...

The leadpipe is relatively bright, if you don't like it, increase the venturi diameter in the openscad file a bit. Post-Printing: Bell assembly instructions: Print tuning slide and both neckpipe parts Sand connections and test fit parts and parts...

I feel like I've gotten a bit better but this is still not a perfect design in my opinion. See the paddle shoulder buttons here: https://www.thingiverse.com/thing:3812331 If you end up selling this design or a remix of it, please don't forget about...

The brackets still work if you have new bits , but intention was to only use stock screws where possible - i'm re-designing a little Of note so far - the bolts that hold into the 2020 extrusion T-nuts should be M5, i sized up M4 The idler holder bolt...

----Update----I've added some optional edge trims to cover up the edges a bit. Print 4 edge trims for the vertical edges and one top trim for the top. The top trim features 4 arrows that denote where the chosen symbol should be orientated. There is...

You can buy them separately, but that can be a bit expensive since they only sell them at high quantities... so except for the square bolts, buy generics. Screws: * 14x Makerbeam M3 Square Bolts to hold cross-beams, I believe a few of them come in...

You may have to clean up the end(s) a little bit but in mine I just had to give a little pressure and the rod slid into the hole no problem. If one side is tighter press that side in manually first and then slide the other module into the looser rod...

After conducting experiments on those exact same materials with results similar though showing a bit more variation. ...Thus creating awareness which they both needed about Gold composition – we all need them so we understand its origin even till now...

The tool-side connectors are designed with a split base that gives you just a little bit of flex. It should slide snugly over the tool's dust port where you can tighten it in position with a hose clamp.Once everything is installed, the connectors...

You will have to trim the image to fit as its a bit oversized. Use the acrylic as a guide to trace where you need to cut).-Glue the top ring together and place it on the top, secure it with 6 small screws. -Use double sided tape to attach a middle...

I recommend to let a bit more USB Cable from the cam run free, so that I can bend without giving force to the X-Axis Cable from the Extruder. Install the cam cable when the x-axis is on its most right position. I had one earscope that suffered from...

Hello, when I designed the Z40 some players made me the remark and rightly so that the handle was too horizontal ...so I redesigned the thing a bit and named it the Z45. As always it is forbidden to sell under penalty of criminal prosecution. List...

 Disassembly is generally a little bit fiddly (for example, the mainboard will need to be disconnected from the radar eye LED at minimum and possibly from all other LEDs, microphones, and sensors.  The IR sensors for “follow-me” mode are glued in...

Note that the bearing will sit a bit above the surfaces; this was done for clearance purposes. Parts: side passive, side active, corner brace (x4), clip securer (x8). Carefully insert the clips on the short side of the corner braces into the...

3 - The eyelashes are a bit tricky and some patience is needed during assembly (having extras handy will make the process better). Even though there are small slots in the head for the lashes, they are just guides and add to the eylash effect. Put...

The little spring for the selector pin is from a pen.You will need 3 TEZOU 21a switches(omron may not fit without filing), You may need to shave the tezou's a bit to get them in the lower.You need a tt gearbox ( the blue 1 to 90 ratio metal geared...

This is the biggest component to print, maxed out my print bed at about 124mm across - 1x di_dino_tray_large: For holding most of the herbivore dinosaur meeples - Three di_dino_tray_small: One for water dinos (about half of them), one for small...

Standard 50mm (2inch) vacuum cuffs tend to work loose in use on many tools and are rather bulky, so I was looking for a simple locking system that would be easily adapted to any tool, so that anyone with rudimentary cad skills could customise...

Okay, you have been forewarn, read on Bill of Materials There's also a fair bit of fasteners to gather. I have reduced this requirement to minimal, including the required bearings.. 1 x 6364 KEDA 190KV brushless motor. Other 6364 motor will also...

So I suspect it is a mixture of bronze and the darkened color of the degenerate remains (see photo above).to have a soft, cushioning surface on which the cassette rests.I achieved this by:Printing the part with a color change from black PETG to...

  Assembly is quite straight forward, and a little bit of patience in getting the size right will be rewarded with a very neat finish.SELECTING THE BOTTLEAny bottle will do, as long as it has a section with parallel sides that can be cut to fit the...