dovpo topside dual battery door replacement 3d models

Battery door keep opening randomly? This is the fix. ... I scaled the print to 9.4% for mine to fit perfect.

This is a fix for the Dovpo Topside 90W battery door issue.

Customizable Stand for the Dovpo Topside Dual Vaporizer. Enhancements Made: Vaporizer stand design is now fully customizable. Stand Height: Lip height has been increased to 15mm from the original 10mm. Smoothness Enhancement: The STL file's...

Cup holder insert designed specifically for Topside Dual mods. The design allows for a few mm extra on either side and includes filleted edges to make insertion easier while driving. Cutouts are carefully crafted to fit seamlessly into cup holders...

Resized and added lip to the squonk bottle side so it clips on to the mod.

This model is a design I refined over a few weeks to solve the original battery door issue on the Dovpo Topside Dual Squonk vape mod. On the original mod, the battery door retention was terrible and their is no way to fix it and since I was cheap, I...

... English : I have quickly draw this vape support for the Dovpo Topside Dual 200W because i didn't found any spot to put my vape on ^_^ Works for a Tesla Model 3, should fits into every car with a cupholder... ! ...Ditch the paper go for vapor !

After the second broken door on my Dovpo topside, I created a mini clamp to secure the battery door in its proper position.

Cup holder insert designed specifically for Topside Lite mod. Slightly wider on either side to ensure a snug fit during driving, with carefully filleted edges for smooth insertion. Cutouts are strategically crafted to seamlessly fit into cup holders...

As the title clearly states, this is a cup holder specifically designed for your Dovpo Topside and spare squonk bottle. The acceptance ports on the latest model have been intentionally made larger to facilitate easier PLA changing, especially during...

A Versatile Container that Accommodates a Dovpo Topside, a Secondary Fuel Cell, and a High-Capacity Battery. ... Customizable Design, Complete OpenSCAD Source Code Provided.

pretty simple, just wanted to print my own custom button for my dovpo sq clutch mod. ...doesnt matter what plastic

I quickly drew up a support for the Dovpo Topside 90W because I couldn't find a spot to put my vape in the car. Designed specifically for my Tesla Model 3, it should fit into any other vehicle with a cupholder that I haven't tried out yet. ...Give up...

After searching extensively for a 3D model, I finally came across one - only to find it was a commercial product available from 3DPrintler, specifically a 25mm-depth dual-battery door for the DJI Phantom at...

This is a broken battery door replacement for Fitbit Zip activity tracker. Print ABS with 100% infill. ... Created in SolidWorks, source file attached.

The battery door of my HP 200LX is very brittle due to its age. ...One of the pins has already broken of, so I designed this replacement in Fusion360 and put away the original lid to not further break it. This design fits my 200LX perfectly. Best to...

I created this replacement battery door because the original one tended to fall out during crashes on my quadcopter, and I was worried about losing it. Now I have a spare at home while keeping the new design on my drone. ... As an added feature for...

Replacement Component for the Battery Compartment Cover of a K'NEX Thrills Motor System

Replacement battery compartment lid for the Texas Instruments TI-83 Plus graphing calculator.

So, I cleaned it up, replaced an encoder, and designed this battery door. Print settings aren't too important since this is so small. But I'd recommend a low layer height for lots of strength. I made the tabs have a little less spring to keep the...

So, I cleaned it up, replaced an encoder, and designed this battery door. Print settings aren't too important since this is so small. But I'd recommend a low layer height for lots of strength. I made the tabs have a little less spring to keep the...

After I dropped my titan the first time I tried to look for a replacement battery door but you need to buy the entire mod again, which I did the first time.Then came 3D printing in my life. Fun as hell!</p><p>But of course, my precious new mod fell...

So, I cleaned it up, replaced an encoder, and designed this battery door. Print settings aren't too important since this is so small. But I'd recommend a low layer height for lots of strength. I made the tabs have a little less spring to keep the...

So, I cleaned it up, replaced an encoder, and designed this battery door. Print settings aren't too important since this is so small. But I'd recommend a low layer height for lots of strength. I made the tabs have a little less spring to keep the...

My kid successfully misplaced the battery compartment cover on his Nikko controller, which has item number 160700 assigned to it, prompting me to create and manufacture a replacement part.

My son managed to lose the battery door of his Nikko remote (item nr 160700), so I decided to design an print a new one.Print Settings Rafts: NoSupports:YesResolution: 0.1mmInfill:25% or less Notes: I printed this in this orientation, but it should...

Got inspiration from another battery door and completely remodeled my own. This is meant for the Nikon D3200 but I'm guessing it would fit on the other D3XXX series of cameras. Printed with 0.15mm layer height and .35mm line width for a little...

After searching for one I just couldn't fine a 3D model out there besides a commercial 3D printed product from 3DPrintler, so Inspired in 3dprintler.com and having a 3D printer of my own, I was not willing on paying $32 + shipping for a battery door...

Battery door replacement for Canon EOS 450D/500D/1000D Tested on own 450D and it fits great

A remix of https://www.thingiverse.com/thing:2852875 but instead of making it an expanded battery door, this is a standard replacement battery door for the stock BOOMco Spinsanity blaster. Mine broke so I remixed this design to make a new one. It...