door that says pull 3d models

Customized version of https://www.thingiverse.com/thing:42220 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=42220

Customized version of https://www.thingiverse.com/thing:42220 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=42220

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=44212 Instructions Using the following options: 04_pillar_diameter = 18 05_rod_depth = 5 07_pillar_shape = Straight 08_design_style = Orbiting...

A personalized adaptation of http://www.thingiverse.com/thing:42220 was created using the Customizer! ...Accessible at http://www.thingiverse.com/apps/customizer/run?thing_id=42220, this specific design features the following customization options:...

Customized version of https://www.thingiverse.com/thing:42220 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=42220

The push bar attachment can be fitted to any entrance so users don't need to touch the doorknob. ...A mounting aid is provided to ensure accurate drilling for easy installation.

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=11111 Using the following options: Angle Edges = Always On Taper Amount = Heavy Indent Ornament = Orb Stem Diameter = Huge Stem Shape = Bent Screw Depth = Deep...

Customized version of https://www.thingiverse.com/thing:42220 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=42220

A personalized version of http://www.thingiverse.com/thing:42220 has been created with the Customizer! Check it out at http://www.thingiverse.com/apps/customizer/run?thing_id=42220. ...To achieve this, the following options were used: 03_taper_amount =...

The zip pull features a "C" type grip and is intentionally forced over the slider for added security. This design allows the pull handle to be flipped to either side with ease. I chose to use PETG due to its availability in my loaded printer,...

Simon Says (Senso) for the Arduino UNO uses four 32mm Arcade Push Buttons with integrated LED, also featuring an integrated Buzzer and 9V-Battery. This setup is extremely stable and perfectly suitable for children to use. Detailed building...

Parts needed: - 4 arcade buttons, similar to those found at Amazon: B01N549IDL - 1 switch, such as this one on eBay: SCHIEBESCHALTER-2-5-10-50-100-2x-EIN-AUS-2x-UM-6-PIN-SCHALTER-AUSWAHL - 1 active buzzer, like the Piezo Buzzer Summer Signalgeber...

Based on the classicly simple "wire pulls" available almost anywhere. They're cheap and quick to make. I optimized the design by including flats on the top and bottom rather than a true circular profile. Makes printing more reliable and reduces some...

I created some zipper pulls, found here: https://www.thingiverse.com/thing:2964645. These worked so I decided to make Skully Pulls. Jus like the others, this is designed to use with #95 paracord. These are the same exact beads used in the Skully...

I created some zipper pulls, located at https://www.thingiverse.com/thing:2964645. These worked so I decided to make Skully Pulls. Just like the others, this is designed for use with #95 paracord. These are the same exact beads used in the Skully...

If you have hidden drawers, they can be difficult to pull out, especially if they sit over drawers with sharp objects in them. This drawer pull makes it easy to open a drawer where there is no room to put an external handle on an inner drawer. I made...

A pull toy for young kids. Print a base, 4 wheels, 4 axle pins, and a character The axle pins are a tight fit and will need to be hammered in lightly but put somethng between the wheel and the base to avoid going too far or the wheel won't spin.

Made a simple two finger pull you can glue onto your superglue lids to make it easier to yank them off when they inadvertently get glued on… Bob Smith Industries Insta-cure Cyanoacrylate Enjoy!

I added customized nylon string zipper pulls to my backpack, which was originally equipped with dull plain ones, making it easier to grip them now. It works flawlessly. ... Print Settings Printer: Wanhao Duplicator i3 ...

It's a drawer pull. Has slots and holes for 10-32 nuts and bolts. 5mm nuts/bolts might fit but will probably be tight. Print instructionsShould print in just about any material with any standard settings.

Zipper Pull Designed for small and large paper clips. Printed at 60% speed. Removed inner loop of paper clip. May need to reform the loop for your application. Lid slides into body. Glue lid, body & paper clip when fit up complete. ... May need to...

... created by nitr1c and Luki85. ... Modified to feature countersunk holes, ensuring they are perfectly flush with the foot pull. Revised texture now provides superior shoe grip performance. ...Dimensions remain at 90mm.

I opted to craft my own pull cord caps purely because the standard ones are extremely dull. So far, I've only produced basic designs, but I'm eager to create more intricate ones in the near future. ...Check out my project at...