door for teardrop camper 3d models

Ever lose or break that little toggle on your camper's outlets? Well I did. This is modeled to closely resemble the existing one but build with beefier specs. This could also work for some rework boxes. ...Designed it to be printed laying down.

This is a camper shell for the [1964 Chevrolet C10 Pickup pinewood derby car shell](https://www.thingiverse.com/thing:6212331). With this shell, the truck is far too heavy to stay under the 5 oz. maximum weight limit, so you wouldn't be able to...

... different refrigerator models or even other appliances with similar designs. If you like this project and want to explore more innovative ideas, visit our main website at http://www.bvRobotics.com for a wealth of inspiration and creative solutions.

I fabricated new feet for my collapsible table in my camper van. I'm fairly certain the table is a Reimo branded one, though it's an older model, so take a good look at my photographs and be aware of potential differences. Printed in ABS, PLA...

I made new feet for my collapsible table in my camper van. I think the table is a Reimo branded one, but not the newest model, so beware and take a goods look at my photographs. Printed in ABS, PLA might be too brittle. Would love to try Ninjaflex or...

The threaded version is designed to perfectly fit a modern #8 sheet metal screw, which I used to reattach my camper's sidewalls. The threading built into the part reduces layer separation and cracking when tightening it down. For those who still...

Scale Camper Cabin + Bed with separate tire mounts(can mount max 100mm diameter tires) cabin 2 configurations handles of camper cabin could be printed separately as well as together(best results came printed separately)

... of my first 3D-designs with freecad. I added the tube in the center, because the space behind the cover was not deep enough for the installation. The ring on the backside gives stability to the cover plate. ... The inner tube is about 29 mm wide.

I incorporated the tube in the center because the space behind the cover was not deep enough for the installation to be successful. The ring on the backside provides stability to the cover plate. ... The inner tube is approximately 29 millimeters wide.

These are the APACHE letter emblems that go on the spare tire cover of Apache Pop Up Campers from around 1975 and up, including mine, a '76 model. The same size emblems were also used on the sides of some campers after '77 or '78. These letters are...

Check out my other designs for [expedition vehicles and camper vans](https://www.thingiverse.com/zefram_cochrane/collections/cochranes-expedition-vehicle "expedition vehicles and camper vans"). Visit my website for more information:...

This is a siphon for the sink in my camper van. It is directly plugged onto the pipe which comes out of the sink and connects to a ∅32mm gray water hose. It stops the smell from going back up through the pipe. The cap of the siphon can be unscrewed...

I bought a cheep 12V USB-charger for my camper. I wanted a simple one, without leds, one that is not blinking the whole night. When I had it in my hands I saw that there where two parts: A plug socket and the charger itself. That didn't look that...

:-) I made these hooks to mount biclycle luggage straps to the table of my camper van. This way, you can easily fix any loose stuff to the table when driving. The chances are small that you can find the exact same luggage straps i have, but these...

I picked up an affordable 12V USB charger for my camper. I needed a straightforward one that wouldn't keep flashing lights all night. When I got my hands on it, I noticed two separate parts: a plug socket and the actual charger. That didn't look...

The likelihood of finding identical luggage straps is slim, but these versatile hooks should be perfectly suited for other straps as long as a M4 bolt can pass through the end caps - I've even drilled a 4mm hole to make it happen. ... These sturdy...

Custom mounts to install a small shelf below the rear right window of a Ford Tourneo Custom (L2). ... This is part of a camper conversion and quickly tailor-made to the actual dimensions with given inaccuracies.

It come with 3 types of wheel setups Printable Tire and wheel Printable Wheels for glued tires Printable Beadlock Wheels for a larger variety of tires Printable tires are about 3.9"/94mm high. You can probably go bigger but I do not know how the...

Inspiration (threaded hose coupling) taken from: https://www.thingiverse.com/thing:5153808 These are made to fit my Weinsberg 600 DQ (2019) camper van. Seem to fit well, but I haven't actually filled any water yet was weather is awful and I'm not...

A small shelf designed to fit the angled front wall of a KZ181 Camper Trailer.  It may fit other with an angled front wall. The angle from vertical is 25 degrees.  The shelf has a small lip, with a flat surface 204mmx94mm.There are no screw holes as...

... To gain easier access to stored goods in the fridge, you can lift the bar within the clips and then fold it down. Before closing the door, you can fold up the bar again, securing the stored goods from falling out when opening the door next time.

I needed a safe place in my camper to charge and store phone or other accessories. I designed this box which can hold 4 USB charging ports and a global switch to poweroff everything and save battery when not used. I decided to integrate with a shelf...

A small shelf designed to fit the angled front wall of a KZ181 Camper Trailer. &nbsp;It may fit other with an angled front wall. The angle from vertical is 25 degrees. &nbsp;The shelf has a small lip, with a flat surface 204mmx94mm.</p><figure...

Users rate me highest for providing a waterproof cable entry solution suitable for any usage. I successfully employed this method for installing solar and antenna cables in my Morohome, resulting in optimal performance and protection from the...

The cross is used for centering during assembly and can be removed afterwards with a cutter. determine position, mark holes, remove cross, screw tight. ... It is recommended to first screw the 3 large holders tight and then adjust the desired...

Mount for LED lamps. ...For fixing the lamp, two M5 screws and 6 M5 nuts are used. The second file, you can use only two M5 screws. ...Thread is already sealed printed on a Photon S printer layer 0.05 mm Normal exposure times 8 sec off time 4.5 sec

... ...The necessary tools must be available for assembly.Minimum print area: 250x120mm (210x120mm Short version)UPDATES2024-04-15 - Short version added. ...Optimized for a print area of at least 210x120mm.2024-05-04 - Added a short version of the axle.

The necessary tools must be available for assembly.Minimum print area: 250x120mmUPDATE:2024/06/14 - 024_Front_Box_Side_2x_v2.stl - Fixing an insufficient hole.2024/06/24 - 015_Side_R_v2.stl - Fixing an insufficient hole, 018_Body_Cover_v2.stl -...

... rod. ... When not in use, it allows table to hang down, or to be removed by simply unclipping the table from the rod. For the removable leg design to hold the other side of the table look at m over design: https://www.thingiverse.com/thing:4790535

If the requirements for stability are higher, you can of course also use other materials such as PETG or PC-CFLayer thickness / mode: 0,2mm&nbsp;Infill: 20% for stability 50-100%&nbsp;I wish you a happy print and I am happy about your...