dji mavic mini 2 ipad mount 3d models

I recently printed this custom part using my IIIP, and while it turned out well, the iPad Mini was slightly too long. By sanding down the top and bottom interior sections, I achieved a perfect fit. ...This project is inspired by Arod24's original...

Strobon Mount for DJI Mini / Mini 2. This design clips on to the back of the drone and has a dual feature. It holds the battery in place and allow you to mount a Strobon Cree in it Due to the minimal design the Drone still weighs in under 250g when...

Redesigned the Mavic phone holder originally created by YohannG, then updated by AlanMoulding for use with the Mavic Mini DJI Controller. The original design wouldn't fit my iPhone 11 pro with a case on, so when I first printed this design, I had to...

Dji Mavic Mini 1 Remote Controller Adapter for phone Holder I designed it to be compatible with any Phone holder with a tripod mound screw For example I am using this one form amazon:...

DJI Mavic Air 2 Front & Rear Strobe Mount for the Ulanzi DR02 Strobe Light. The front mount has been designed for the Ulanzi DR02 Strobe Light to permanently mounted to the mount via 3M VHB tape. The strobe can still be charged via the hole in the...

I designed two iPad mini attachment options, one compatible with Apple Smart Covers and Cases, the other without. To bring these designs to life, I printed them on my Da Vinci 1.0A using specific settings: Layer height is set at 0.2 mm, 3D density at...

Rear feet are permanently installed using the factory screws, these fold up with the drone and can still be used in the Mavic Mini case. The front feet just clip on before flight. ... If you like my designs, consider donating whatever you feel it's...

... I'm certain that the float can support the drone on the surface and ensure that flight performance remains uncompromised. mavic_mini_buoy_V2_fixed.stl has been updated to improve the opening of the battery compartment by shortening it by 2.8mm.

Don't hesitate to like it if you like it ;-) File in very high definition. ... Storage to be integrated into the Mavic mini's case. ... (to be placed under the charging dock) 3 compartments with hinged lid Dimensions 123 x 73 x 30mm

Sources for building and flashing to Arduino Nano V3 can be found at https://github.com/czipis/mavic-mini-battery-info. All required parts can be purchased from AliExpress for approximately $6, with a detailed list of necessary components available...

I hate having to remove sticks from my controller each time I put it away in its case, so I created a 'stick guard' to suit the Mavic Mini. The current carrying case requires that the sticks be removed otherwise undue pressure is applied to these...

The Mavic Mini will be irreparably damaged, but whoever is covered by disaster insurance will be able (maybe) to return it to receive the replacement. It is therefore suitable for those who takes off into the open sea from a boat. It must be aware...

This recovery float is intended for easy recovery after a fall into the water. The Mavic Mini will be irreparably damaged, but whoever is covered by disaster insurance will be able (maybe) to return it to receive the replacement. It is therefore...

This recovery float is designed for effortless recovery after plummeting into the water.\nThe Mavic Mini will be irreparably compromised, but those with disaster insurance coverage may possibly return it to receive a replacement.\nIt's perfect for...

Update: I've created an improved mount for the Mavic and P4 that can be found here: P4 - https://www.thingiverse.com/thing:3791014 Mavic - https://www.thingiverse.com/thing:3791049 The knob and the base plate for the CrystalSky are remixed from...

Ready to showcase your Mini every day? ...Want to keep it out of the box and on full display at home? Use a Display Stand to turn your Mini into an eye-catching centerpiece, always ready for action.

for 2 ~4 Batteries

Design was tested with Mavic Mini and Mavic Mini SE, however I believe it would fit on all Mavic Mini versions. I tried to put the design on top of the center of mass of the drone such that it influences flight as little as possible. Printing: I...

... a Phantom 4 and Inspire 1, and really enjoy how my iPad attaches to those transmitters. ...The DJI Mount costs around $30 and is available on Amazon as Part 45 from DJI. ...To secure it, I used an M6 blind nut bought from eBay and an M3 bolt and nut.

This is a revised design based on [Helichrissi's](https://www.thingiverse.com/thing:4406509) Mavic Air 2 phone holder creation. My objective was to enhance the original by adding more screws for extra stability and creating a larger version that...

The file formats available include: 3ds Max 2012 V-Ray (2.4) and standard materials scenes OBJ 2012 (Multi Format) 3DS 2012 (Multi Format) FBX 2012 (Multi Format) Maya 2012 with standard materials Cinema 4D R12 with standard materials Textures are...

This is a remix of Helichrissi's Mavic Air 2 phone holder design. My goal for this remix was to make the holder a little more sturdy by adding more screws. I also wanted to create one that was slightly larger to accommodate my phone with an Otterbox...

Mount the Clamp Mount securely to ensure a stable fit. Install the Top Holder carefully, positioning the Off-Switch exactly as required. Next, attach the Bottom Holder firmly in place, taking care not to touch the Power Switch. ...Proper alignment of...

... to control joysticks. ...I went through few designs but and ended up with this one because it feels most comfortable with the weight of the iPad. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/aCma05qJBXQ

I wanted to add this clamp (https://www.thingiverse.com/thing:4607018) in my motorcycle, so I took Tfede's thing and I added the Gopro style mount to attach it to a RAM Mounts ball for gopros. I still haven't tried it but it fits pretty well. ... I...

Frame for the DJI Mavic Air 2 camera

This iPad mini Enclosure is designed to use your iPad mini as a point of sale counter top system

This iPad mini Enclosure is designed to use your iPad mini as a point of sale counter top system

This is a modified version of the original DJI Mavic Pro camera attachment, minus the GoPro mount option, freeing up sensors at the base of the Mavic Pro.

A simple remix of "Dji Mavic Mini / Mini 2 Case (Remix) w/ RC Case(s)" but with the top props enclosed as requested by a comment. ...I have included the original "maviccase.stl" in the files as well.