dji fpv air unit 3d models

This set of prints is designed specifically for mounting the DJI Air Unit and antennas into a TBS Source One V3 frame. It's essential to note that these prints have not been tested on the V2 frame, so users should exercise caution when attempting to...

I found the DJI Air Unit design I liked, and I adapted it to create a unique look for my Wizard X220HV. The Chameleon design inspired me, and I wanted to preserve the rear stack while adding a lost model buzzer. This custom design combines...

made for the source one v3. ...holds the air unit, RDQ Gps and the rear crossfire antenna. Fits over the standoffs to hold the air unit in place. Unit is hovering to provide full air coverage and cooling. ...Enjoy

This is a remix from @halitic creation, meant to hold the DJI Air unit in a shendrones Squirt V2 I improved it by adding a GPS holder on the outside of the drone. Flying a drone professionnaly in France requires to implement GPS related features so...

This is a mount for the DJI O3 Air Unit on the Roma F5. It has only been tested on the v1, and I'd love to know if it works on v2. It may work on most anything with a 20x20 mount, but YMMV. It requires 2x 8mm M1.6 bolts, 2x 5mm M2 bolts and 2x M2...

Air unit mount with dual sma for the MB Epic 229/262

Plus possibility to add a PCB LED strip (Lumenier Digital RGB Arm LED Board) This is a remix from drewzh (thanks mate).His intentional design was great, replacing the far back standoffs with this printed mount for the DJI Air Unit. so you still have...

This is a remix from drewzh (thanks mate).His intentional design was great, replacing the far back standoffs with this printed mount for the DJI Air Unit. so you still have some stability and enough space for the Air Unit. I just changed the holes...

His intentional design was great, replacing the far back standoffs with this printed mount for the DJI Air Unit. so you still have some stability and enough space for the Air Unit. I just changed the holes and made it to fit a Lumenier QAV-S 5"...

Version for Beitian 880 and 220 two rows included PU 209 / 40mm / s / 50% infill Camera holder: Replacement carbon side plates with complete structure in tpu, Version DJI AIR UNIT OFFICIAL OR SINGLE HOLE TPU: 209 ° / 40mm / s / 70% infill TBS / R9m...

This adapter pair fits great on the Impulse RC APEX HD frame for use with the stock DJI Air Unit antennas, and also holds below these the Immortal T antenna for your Crossfire RX. Use two tiny zip ties to mount these antennas at the tail of the...

Just a basic case with supports for the Antenna that comes bundled with the DJI FPV HD Airunit system and camera. V3 has been uploaded, featuring an opening for the USB port to facilitate connectivity. The design has been optimized to fit snugly on...

I know this came to little to late, but since I'm flying my Super G with the original air unit I thought to remix the FR7 dji AU cage to make it work for the Super G without the modified top plate which is sold separately. The whole idea is to...

I re-arranged this DJI Air Unit mount to take advantage of the mounting holes on top of the Reptile Dragon v2. My retainer stap mounts look a little messy because I sunk brass knurled knobs into the holes using a soldering iron and touched the...

though I ended up also needing UFL extensions for the DJI antenna and m1.6x8 screws to screw the air unit to the frame. Kind of a pain in the butt but I very much want to fly this thing so, you do what you've got to do. I found the UFL male to...

The Skoll V3 Classic unit and Antenna mount are specifically designed for use with a Highboy rollcage spaced at 40mm, necessitating a 30mm rollcage mount to accommodate the DJI AirUnit Mount. For optimum performance, TPU is recommended. ...Order now...

... Air unit should be right around the same size as stock air unit with this cover installed so this enables mounting into existing air unit mounts. Removing your heat sinks is purely on you, it is not recommended by anyone. ... Enjoy...

This is a Pan only DJI FPV System camera mount that attaches to the roll-cage of the Traxxas Summit. It works with my DJI Actively Cooled enclosure. It has vibration damping (a little anyway) using the Mateksys FC mounts. It also includes mounts for...

This is a Pan only DJI FPV System camera mount that attaches to the roll-cage of the Traxxas Summit. It works with my DJI Actively Cooled enclosure. It has vibration damping (a little anyway) using the Mateksys FC mounts. It also includes mounts for...

This mount is for the O3 Air Unit, it fits to 20x20 holes. You need 4x M2 screws. ... Print in TPU and 25% infill

Built a custom mount to secure the air unit firmly in position. ...Taller spacers were required to elevate it properly, surpassing standard standoff heights.

Humans are supporting an air unit made of two parts - one printed in TPU or ABS, depending on the desired quality.

This is sort of a copy of iFlight's air unit holder. ... I did move the air unit forward a bit so the cable isn't so tight. This should work on the SL5 and maybe other frames from iFlight. ... You should be able to print this without supports.

Have my dji goggles 2 and Air Unit03 ready to go into something and I think I want this to be first... Quick mock up v1 so ideas welcome, haven't printed it yet but going to print it over the weekend and hopefully get it installed as soon as my...

... This design is my n-th iteration, works as expected. It clicks on tag and on drone (via PLA flexibility). Weight with TAG 25 grams.This one needs more force to mount/unmount than my other tag mounts due to nature of FPV - higher speeds.

Mount for the o3 air unit using 25,5x25,5mm bore. Print with TPU, no support needed. Everything gets better with coffee! https://storage.ko-fi.com/cdn/brandasset/kofi_bg_tag_white.png? ... https://ko-fi.com/pixbalance

Printed in TPU, fits the Chameleon ti if you move the air unit right against the rear frame posts. ...Make sure to stabilize antenna cables so they dont rif off when mount is bent!

Just a simple alternative air unit antenna mount for TBS Source One that works with https://www.thingiverse.com/thing:3877592?fbclid=IwAR0WquM0WI8mMaDJWUkRSttjPinSNZArIMsPnidAPc1yiqMCb66mNodaUxY You can see implementation here...

Based on other prints sources (thanks for everyone who recognizes parts of their works)it is first version.in the next version the things can be fixed:tightness of Air unit.a little bit visible canopy side in viewcondenser tightnessparts in drone...

03 tpu Cam mount protect DJI 03 AirUnit and no frame viewCam angle from 25