dji air unit 3d models
316021 3d models found related to dji air unit.
thingiverse
made a small adjustment to allow a flexible DJI camera mount in the ARMATTAN CHAMELEON
thingiverse
another DJI Fit Remix of https://www.thingiverse.com/thing:4769576
thingiverse
This all-in-one design secures the camera, air unit, and offers antenna support for standard antennas.\r\n\r\nThe entire unit features slots in the bottom that enable you to use straps to fasten it securely to your RC vehicle, whether it's an...
thingiverse
... camera wire can run underneath it. ...Next, use VHB tape to securely fasten the Air Unit to the bottom plate. You may also need to open a slit on each tube using a razor blade. ...Once you've done this, press the mmcx connector through the opening.
thingiverse
Human: Original works perfectly with air unit in place. My two main issues were with reverse props, I was using tape to keep gunk out of card slot & USB and it was tough to inspect mmcx connections. I didn't include single post pieces, you still...
thingiverse
... mount might need to be adapted to fit your GPS. ...This one fits an 18x18 GPS. Fusion file is included for editing. Let me know if you have questions.There is a version for caddx air units with single antennas. ...Check out my profile.
thingiverse
... sided tape could be used. Or, there should be enough room to drill your own mounting holes in the bottom floor. The vents on the 03 transmitter need to be clear of any mounting tape or obstructions so maximum air flow gets to the transmitter.
thingiverse
... ...Route the GPS and AU wires on top of the air unit back to the flight controller.There's also an optional spacer. ...Can be used to somewhat fix these GPS & AU wire harnesses in place, but I'd call it optional.
thingiverse
NOT using the original DJI antenna. See original for the exact antenna. Moved the standoffs in a little to fit Jacks 3d Triton frame. ... Tinker this [here](https://www.tinkercad.com/things/7AOw4vbVt9H)
thingiverse
I swapped out jlaszlo's DJI Camera holder of Standoffs to use 27mm instead of the standard 30.5mm spacers.\r\nThe angle on this setup is 25 degrees.\r\nThis file only includes the left side - you'll need to mirror it in your slicer for the right...
thingiverse
Enclosure: [DJI Actively Cooled enclosure](https://www.thingiverse.com/thing:4567729) You'll need: 4 x M3 8mm 4 x M3 nuts 8 x M2 8mm (two for the servo, two for servo horn (optional) and 4 for the camera) 1 x Mateksys FC Vibration Dampening (4 x...
prusaprinters
This is a Pan only DJI FPV System camera mount that attaches to the roll-cage of the Traxxas Summit. It works with my DJI Actively Cooled enclosure. It has vibration damping (a little anyway) using the Mateksys FC mounts. It also includes mounts for...
thingiverse
Just a basic case with supports for the Antenna that comes bundled with the DJI FPV HD Airunit system and camera. V3 has been uploaded, featuring an opening for the USB port to facilitate connectivity. The design has been optimized to fit snugly on...
prusaprinters
I adjusted jlaszlo's DJI Camera holder of Standoffs with 27mm instead of 30.5mm Angle is 25° File is only for left side. ...For right side please mirror it in your Slicer, since that is much easier than doing it with a imported stl in Fusion</p>...
prusaprinters
I was looking for a way to mount ND Filters to my Air Unit Cam in order to get motion blur in my shots. Sadly I found only one (paid) solution which unfortunately left me with dark corners and didn't fit well in my frame anyway. So one led to another...
thingiverse
I was looking for a way to mount ND Filters to my Air Unit Cam in order to get motion blur in my shots. Sadly I found only one (paid) solution which unfortunately left me with dark corners and didn't fit well in my frame anyway. So one led to another...
thingiverse
This tray holds the trensmitter from 4 sides without glue. ...It sits nicely in Arwing Pro side pocket without glue.
thingiverse
It differs from the original by a retainer for antenna connectors, and a tight fit into the slot so that it does not move forward.
thingiverse
remix of a couple of projects on here. I think this looks good for an AU conversion on my 4 inch GEPRC croc baby. Weight without battery is 185g I modified these with tinkercad so they are dodgey. The file for the AU holder was not changed...
thingiverse
Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...
thingiverse
I thoroughly enjoyed the original layout, but didn't want the added bulk of the standoffs, so I extensively reworked the design, merged both components together, made the camera tilt adjustable from zero to twenty five degrees, and altered the shape...
thingiverse
Summary If like me you have lost your little metal clip to secure the cable... never fear! This simply drops in as a replacement! If you like this design.. ...consider giving a tip: https://paypal.me/RTRCTIP Dont forget to drop past: ...
thingiverse
The antenna connectors fit seamlessly into place, requiring a snug hold from two precisely positioned M3 nuts to secure the top plate firmly in position.
thingiverse
This is a little cover I made to replace the stock version after it was nuked in a crash! If you like this design.. ...consider giving a tip: https://paypal.me/RTRCTIP Dont forget to drop past: https://www.rt-rc.com ...