dji air unit camera 3d models

The enclosure is a lot simpler to build than my other unit and is quite a bit smaller.Update - April 2022I've added an alternate main body with holes for both the USB and SD card slot to make updates and storage more accessible.See here for camera...

Nose Mount for 03 CameraFits square slot at front, Angle is pretty close to matching the planes shape10 Degrees of Angle adjustment on CameraAir duct also to suit camera mount availablePrinted in PLA for myself

This is a mount for the DJI Air Unit on the Tricopter LR designed by David Windestål, available at https://rcexplorer.se. *** The printed version may require additional volume in the X/Y region to accommodate the air unit. A 1% increase could...

This DJI FPV System camera unit and air unit enclosure is actively cooled and specifically aimed at ground FPV enthusiast where there isn't going to be enough airflow to properly cool the Air Unit. The unit is cooled by two 40mm fans (5v in my case)....

Revised canopy for Albabird FPV model aircraft to take DJI air unit with pan and tilt unit for camera. Canopy has a 15 gram weight penalty over the standard canopy supplied with the model but has much improved drag characteristics and will give...

Holds a DJI Air unit on the bottom of a BOTAFX frame, you'll want to rotate so is printed "standing up" with the triangle/trapezoid at base pointing upward and use TPU for longevity.

Attach a 40mm cooling fan to your DJI Air Unit. Very useful for ground vehicles. You will need 4x M3 bolts. ...Length will depend on the thickness of your 40mm fan.

Naked DJI O3 Air Unit Case Remix of the Original Removed the Little Knob on the Inside for the SD Card holder at the Mid Part. ... Leave a like :)

DJI Air Unit MMCX Antennas are available, perfect for securing the antennas with the DJI Air Unit securely. Measuring 30mm in height and 25mm, they are designed to fit perfectly around M3 standoffs. If shorter standoffs are used, the antenna can be...

I decided to use this mount for my Dji Air Unit Antennas. I bought the Dji mmcx to RP SMA adapters and mounted them to this. It works fantastic. ... Updated 3/26/22 to add 2 mount options and a 3rd mounting option for adding a longer antenna for your...

This DJI FPV System camera unit and air unit enclosure is actively cooled and specifically aimed at ground FPV enthusiast where there isn't going to be enough airflow to properly cool the Air Unit. The unit is cooled by two 40mm fans (5v in my case)....

This is a mount for the DJI O3 Air Unit into the Squirt V2 platform. The antenna is held in with friction between the mount and the top plate. The block holds the air unit in from the top and leaves enough room to access the USB port. Print using...

This DJI FPV System air unit enclosure is actively cooled and specifically aimed at ground FPV enthusiast where there isn't going to be enough airflow to properly cool the Air Unit. The unit is cooled by a 40mm fan (5v in my case). The enclosure is a...

Slim saddle type mount for the DJI O3 Air Unit. Allows to pass cables through as well as a zip-tie to attach a receiver or other accessory on top of the air unit. The air unit sits on top of this saddle mount. The bottom screws of the air unit need...

This DJI FPV System camera unit and air unit enclosure is actively cooled and specifically aimed at ground FPV enthusiast where there isn't going to be enough airflow to properly cool the Air Unit. The unit is cooled by two 40mm fans (5v in my case)....

It was made for dji air unit. It also has mount for servo support. I didnt print it yet (2020\11\04) since my model hadnt arrived yet. There are three parts there. Front nose part, back part for air unit and antennas holder. You need sma antennas and...

DJI Air Unit mount for the Armattan Badger. ~8g printed at 30% infill. 4 perimeters. It's designed to pass the 12 gauge battery wires underneath the air unit. Antenna mount clamps down a bit on the cable. You can put heat shrink on the cable if you...

A mounting plate for the DJI Air Unit for the Hildgard 395 V6. Attached via M2 screws through existing holes in the top plate. The holes in the mount are deliberately undersized and if drilled out with a 1.6mm drill the M2 screws will self tap...

hello the file allows not to have the spacer in the field of the camera. ...and to maintain the air unit o3

I have increased the length of the sled by the servo hole. ...This way the camera wire will not be touching and scrubbing the Air Unit.

A mount to fit a DJI FPV air unit in an Armattan Gecko 3" without modifying the frame. Make sure your fc + esc are under 7mm, and you get 1.5mm of clearance between the air unit and the plastic connector plugs. You can raise the top plate with...

I noticed that the original models for the DJI air unit antenna mount had a gap between the main body and the connector tabs; this resulted in the connector tabs being printed as separate pieces and being very weak. I filled the gap to fix the...

This is a generic mounting cage for the DJI FPV Air Unit. There are M2 scew holes for mounting to any flat surface. The bottom plate is optional to reinforce the attachment under the mounting surface. ... Print in TPU (the lid can be printed in PLA for...

I crafted a bespoke mounting system specifically designed to integrate the DJI Air Unit onto the v2 Source One frame with precision. To achieve this, I opted for a sturdy TPU material and implemented a 10% infill pattern for added durability. ... ...

Here is the rewritten text: I've remixed my current design for the iFlight DC-3 DJI Air Unit Cage, giving it a sleek new look by cleaning up the edges and shaving off some extra weight to make it even lighter.

This are the models i use to hold in place my DJI o3 air unit in the PiratFrame Sloop v3. The base is fixed with two screws in the bottom instead of the metal rod and the antenna/gps part is simlply pu on the two last rods. ... the gps i use is the...

This is a generic mounting cage for the DJI O3 Air Unit. There are M2 scew holes for mounting to any flat surface. The bottom plate is optional to reinforce the attachment under the mounting surface. ... Print in TPU (the lid can be printed in PLA for...

These 2 parts hold the DJI Air Unit itself in the frame. You only need the bottom because the top plate keeps it from coming out. ...The print in TPU is tight enough that it does not move even in a crash.

Naked DJI O3 Air Unit Case Two version one is for M1.6 and the other M2.0 If you want to use M2 version, you need to drill the Vtx board and reaming to M2. ... We have test it, reaming it won't break the Vtx.

Transform your wizardry into a seamless flight experience with this innovative DJI aerial unit attachment.