diy z axis stabilizer 3d models

Enhances Z-axis stability, reducing wobble that manifests as X-Y waviness during Z-axis ascent. For optimal results, enlarge the rod holes to 8mm or 5/16" and the acme screw hole to 1/4". Lubricate the system with a thin layer of grease for reduced...

I've tried various z-axis stabilizers for my Velleman K8400 Vertex 3D printer, but they don't fit because of the different gap between the back wall and the Z axis. So, I decided to design my own with an adjustable distance. The gap between the back...

This is the second revision of my K8400 VERTEX Z-axis Stabilizer published here. I designed it as part of my Vertex Evolution project where the top panel of Vertex will be removed to gain more space. Use plain 608 bearing, four M3x12mm screws and...

This is the second revision of my K8400 VERTEX Z-axis Stabilizer published here. I designed it as part of my Vertex Evolution project where I will remove the top panel of Vertex to gain more space. Use plain 608 bearing, four M3x12mm screws and...

... The STL file "Anet A8 Z Axis Stabilizer Cutted 8597" is specifically designed for users who have their motor extruder mounted on one side of the frame, as shown in the final image provided. ...If any issues arise, please don't hesitate to reach out.

For Ender 3 Pro Z Axis\ Infill is set at 15 percent.

I designed these parts to stabilize the Z Screw and prevent swaying as the Z axis moves, thus reducing or even eliminating Z wobble in your prints. There are many options for similar parts however I did not come across any for the M150 Maylan 3D...

For optimal z-axis stability, connect the rods; two rods offer increased stiffness. Adding a clamp between them creates a rigid frame. Ensure equal distance on top and base before fastening clamps, with x-ends at their highest point for accuracy.

Remove the top traverse aluminium profile (15x15mm) with is held in place by 2 screws at each Z-axis 3. Make sure all 3 T-nuts fit into the profiles (filing required) 4. Install the 608 bearings (press fit!) - keep then straight! 5. install the...

The z-stabilizer is mounted on the upper side of the axis using the rock-solid axis cover as the fixing point. In addition to the 3D printed parts, you will need a proper bearing capable of taking forces along the z-axis without tolerances. This...

I redesigned my z-axis stabilizer for the back side of the printer. The bottom part stays the same and also the lenght of the aluminium profile. ... Check out the first version: https://www.thingiverse.com/thing:4605511 What you need: 2x...

To prevent clogs, modify the design so that the Z-axis has a larger opening. ...This adjustment will ensure smooth operation and reduce instances of jamming.

I already had used in this past (1 or 2 months ago) a Z axis stabilizer for the rod but it seemed that it was bending so i take it off immediately. After seeing several models i couldn't find something that i thought it would be secure to use...

It's important to stabilize the z-axis as much as possible.There is usually a solution with threaded rods. I think they look cheap. So I came up with a different idea. My previous model was a fully printed one. But the problem with that design was...

This assembly utilizes a spiral cut coupler on the z-axis, which is stabilized by a thrust washer assembly to eliminate end-play and correct wobble in the leadscrew. For Prusa users, two spiral cut couplers, four M3 x 50mm socket head screws, and two...

Anycubic Chiron Z Axis Stabilizer I redesigned this from scratch from a nice design idea by "Elcied". It now includes vibration absorption and is overall stronger . The Chiron should come stock like this as it improves print quality and ringing...

I noticed recently that I needed to use a filament guide with my setup since my filament kept nearly getting snagged on the z-axis knob I'm using. I had remixed this part earlier to use 906 bearings in the roller instead of just rotating plastic on...

I created a Z axis stabilizer that includes a bed mount, leveling becomes much easier when the level point is at the base of each Z rod. This is sorta but not really a remix of my old design. It takes a couple of 3mm threaded screws / nuts and works...

This is a quick mod for the Creality Ender 2 pro axis. ... Simply plug the hole at the top of the wonderful handle at the top of the printer to keep the z axis aligned. Print in either PLA or PETG at 20% infill. ...

I remixed the Y rod stabilizer to fit snugly into the screw hole spacing on the upper Z rod covers. Securing the lead screws resulted in instant Z wobble, a mistake I learned from firsthand. A slight looseness of under 1mm was creeping into the rods,...

Robo3D R1+ users now enjoy smooth operation on the vibration and Z-axis thanks to clever axis covers. As a gesture of goodwill, I've created custom hats for all who can't upgrade to the Robo3D R1+. ...Here's the updated Print Settings: Rafts:...

I designed a plug-and-play Z axis anti-wobble system that works with most 3D printers using 8mm rods and NEMA 17 stepper motors (approximately 40x40mm). ...I prefer it to a top cap holder because if the Z rods are not perfectly straight, it doesn't...

My Z Stabilizer for the older SImple wouldnt fit, so I made this quick. You can use with or without screws. There are spots for 2 16mm M3 screws and locking M3 nuts. Very solid and eliminates almost all rod twisting. ... ...

BQ Hephestos 2 Traveler's Noise-Reducing Z-Axis Bracket Cuts Down on Noises When You're On The Move. Built Specifically for Holding 5x14x5 Bearings in Place. ... These bearings need some extra force applied, so you'll need to give them a whack with a...

I remake this, because in my ender Z-axis screw was too close to aluminium profile. Resulted in that I can't mount bearing, or If I mount I can't get the same top position. So I shortened that 1 mm. And actually all works fine. ... Bearing: 608...

I'm trying to minimize the Z-axis threaded rod movement. Originally, the holes were meant for M3 screws and bolts, but I didn't need them in my case. ... Print Settings: Printer Brand: Printrbot Printer: Simple Black Rafts: No Supports: No Resolution:...

I remake this, because in my ender Z-axis screw was too close to aluminium profile. Resulted in that I can't mount bearing, or If I mount I can't get the same top position. So I shortened that 1 mm. And actually all works fine. ... Bearing: 608...

... Geeetech Prusa i3X. You'll need: 2 Stabilizers 2 M3 x 15 screws 2 M3 bolts (preferably with anti-backlash) 2 M3 washers (preferably larger for a better fit) Replace the six of the eight M3 screws that lock the motors to the plate with longer ones.

V2 - Changed the Distance between the Z axis and the aluminum frame made the hole bigger to compensate for low print accuracy ########################################################## Remix Summary I used the Thing...

I created a simple component to reduce z-axis wobble on my CL-260. It doesn't require any screws, instead, it simply slips onto existing 10mm rails. I added an 8mm bearing in the middle and applied some tape for a tighter fit. The distance between...