diy tablet car mount 3d models

I needed a mount for my Nexus 7 tablet in my Kia Soul that could easily be stowed when I wasn't using the tablet and provide security at the same time. To achieve this, I used part of a cheap tablet case for easy removal of the tablet and hot glued...

Magnetic Tablet Bracket Mounts Secure Your Device Anywhere. ...Check Out This Innovative Solution Now: https://www.amazon.com/Magnetic-Bracket-Mounts-Tablet-Innovative/dp/B076MX9R7G/

I craved a mount for my Nexus 7 tablet in my Kia Soul that could effortlessly slide out when I wasn't using it and for added security measures. To make this feasible, I repurposed part of an affordable tablet case, making it simple to remove the...

... iPad models. ...Its sturdy base features three precisely angled holes - spaced 120 degrees apart - allowing standard RAM mount plates to secure snugly in place. ...Ample room is also provided at the bottom for your power connector or lightning cable.

... 164mm. I plan to design a universal tablet mount (for 7" to 12" tablet and all car brands) You will need M5 screws and nuts. I haven't print it yet because i'm not in my home. Si you can print it and leave me a feedback. ... Thanks for your likes.

My long-term plan involves designing an all-encompassing universal tablet mount that can accommodate tablets ranging from 7 inches to 12 inches in size, while being compatible with any car brand available on the market today. To bring this design...

... normally attached to front seats facing backwards. Remix also included remix from this file -> https://www.thingiverse.com/thing:2061636/remixes Fitting may be tight so may have to size up "car mount v3.stl" to 102% Used supports for "bar_1.0_180"

Post-Printing: This tablet holder was printed in ABS with 30% rectilinear infill. Initially, I used 20% infill but the hook broke. To address this issue, I increased the infill to 30%. ...Additionally, acetone vapor smoothing will be applied to boost...

CD Slot Tablet Phone Mount For Car

... possible. If you want to build your own car mount for an Nvidia Shield tablet, try using a layer height of .200 and PLA plastic. ...Don't forget to increase infill density up to 50% and include support structures for the upper mounting mechanism.

Mount Tablet to Car Back Seat Headrest If you have a tabulate case, this print support enables you to securely attach your tablet to your car's back seat headrest. You can provide your passenger in the back with the opportunity to play or watch a...

This is a tablet mount for the new Volvo XC90 (2015-) that might work with the headrest of many new Volvo cars (V90/S90/XC60). Commercial headrests are quite expensive since the new headrests aren't standard. I initially designed the entire system,...

Simple, no hardware required tablet holder (fits Amazon Kindle Fire but could fit many tablets) Just print two and attache to the post of the head rests of your driver or passenger seat to give the second row seat a place to put their tablet while in...

I did find allot of tablet holders for on a head rest without the need of bolts or other (non printed parts). This is fully only printed (beside a bit of glue) I created this one for the Nvidia Shield tablet Note however that you can perhaps design...

I did find a lot of tablet holders that can be attached to a headrest without needing bolts or any other non-printed parts. This design is fully printed, with only a bit of glue required. I created this one specifically for the Nvidia Shield tablet....

This is designed to fit snugly in the 1/2 DIN slot under a car stereo, that empty space most stereos leave behind. It's made up of simple shapes, because TinkerCAD is all I can handle! ...Print one body, two arms, and glue them together - making sure...

Rounded car mount remix of https://www.thingiverse.com/thing:4644828 has a 1.5 inch or 38mm base I made it so its easier to install magnets from underneath. ...Follow magnet mounting instructions from https://www.thingiverse.com/thing:4644828

I utilized this product to install my previous Galaxy Note 10.1 and now Galaxy Tab S 10 in my vehicle, employing it for GPS guidance and navigation.

Simple but effective headrest mount for Nintendo Switch or tablet. Originally designed to also fit Amazon Fire 7in with kids case, it has been updated to include 10mm (iPad), 12mm, 14mm, 16mm and 20mm thick tablets to hold most tablet (and case...

Simple but effective headrest mount for Nintendo Switch or tablet. Originally designed to also fit Amazon Fire 7in with kids case, it has been updated to include 10mm (iPad), 12mm, 14mm, 16mm and 20mm thick tablets to hold most tablet (and case...

IPad, Iphone, Galaxy, Tablet holder for dodge cars with Uconnect systems

Tablet iPad Holder for Car Mount Headrest I bought (that breaks super easy): https://amzn.to/471mw10Printer Used is an Ender 3 V3 KE and printed at 15% infill and 300mm speed.https://amzn.to/47Yu8TmThis uses the bolt from Thingyverse item 1460364 but...

This mount can support any phone or tablet on the market, and fits snugly into the 1/2 DIN slot in your dash - that empty space underneath your stereo system. Print three arms, one body, and assemble them together with glue. I had planned to...

Experimental tablet mount

One is specifically made for mounting, and if extra security is required, it can be secured using M4 screws. The remaining two are designed to hold the tablet firmly in place. ...To do this, you will need two rods (10 mm x 8.5 mm) that are precisely the...

This is just another tablet mount for schelfs 18 mm thickness. The assembly of the pieces was done with 4 mm diameter bolts. ... For the knob I used 5 mm bolts.

... design: XarmSlotV3.stl, X_armholesV2.stl, and XmountV3.stl. This was my first attempt at creating a tablet attachment, and while it works, it leaves room for improvement. ...With an Otterbox on my Surface Pro 4, the hooks require a depth of 15mm.

The part is used to hold a tablet on top of the printer with a 2020 extrusion bar. ...It can be used in two configurations; 1- Use two open parts on right and left 2- Use one closed part with one open part The screw hole is 4 mm, I used an M4x10 mm...

Buddy wanted me to hook up a mount they'd discovered here, so I snagged the STL file, remade it on the spot with my printer in mind, and then seamlessly integrated the design with the native FreeCAD capabilities.

I'm Looking For a Tablet Car Holder That Fits My Huawei M5 Lite Perfectly, But I've Heard the VW Passat Isn't the Best Ride for It.