diy modmic 3d models

UPDATED V1.1 Added basic file that is just the core without extra features for a budget microphone, also made the magnet hole bigger. I designed this because I was too tight-fisted to buy a genuine mic when I had a decently working low-cost headset....

Just a diy ModMic to add a mic to your headphones; the circuit is to be used as a replacement for a Yaesu MH-31. You can choose the lenght printing more longs or small arm parts; I printed 2 long in order to have the mic in front of my mouth and...

A basic charging station for the MODMIC WIRELESS by Antlion Audio!

The K7XX Headphones' Lacking Design Was Causing Me to Lose Sleep Over the Constant Struggle of Finding a Perfect Spot for the ModMic. It Wouldn't Stick Long Enough, and I Needed a Solution Fast. ...So, I Rolled Up My Sleeves and Designed a Solid Surface...

Was getting frustrated with the modmic losing adhesion from the k7xx headphones as there was no perfect spot for it. Designed this to allow for a solid surface for the modmic to attach to. I printed mine with the pad side down. ... Category: Music

... Mounting System by HeyVye. ... https://www.thingiverse.com/thing:2194278 It basically turns the Modmic in a desktop speaker. A 6x2 mm magnet is required and should be glued in. ... Should be printed with supports with the flat side of the hooks down.

A handy adapter to shield the rugged edge of the modmic mount when the microphone is detached, preventing accidental scrapes or scratches. ...Simply require a small 6x2 mm magnet and some adhesive for a quick fix.

The genuine modmic cable clips are far to expensive for this little plastic in my opinion. So i designed them for 3d printing. ...Works quite well for me.Single wall print, add brim to hold it to the print bed.

1x ModMic Attachment 1x 5x1mm Magnet 1x Double-Sided Tape (1cm diameter circle) The best quality you can set your printer to would be optimal, especially for the 4 little fins that protrude out of the base. ...You may also want to use super glue to...

This is a ModMic Wireless Mount that conforms to the MultiClip standard and is meant to slide into my [modular ear peice design](https://www.thingiverse.com/thing:5894991) or whatever else you may come up with. The magnetic mount that comes with the...

I have a modmic v5 that I wanted to attach to the headset, but the metal mesh wouldn't let the adhesive bond enough to keep the mic attached. The mic and baseplate would constantly fall off even when I cleaned the mesh with alcohol wipes before I...

This device perfectly mimics the design of standard clips sold by ModMic, allowing users to securely combine their headphones and microphones into a single convenient unit. ...It serves as an essential tool for organizing cords, eliminating clutter, and...

A simple attachment designed to replace worn-out or damaged sticky pads, making it easy to mount a ModMic microphone to the Monoprice Monolith M1060 headphones. ...This attachment clips securely onto the headphone's stock outer grill, providing a...

These are custom modmic clips designed to fit perfectly on the headphone cords that come with the Superlux HD 668B headphones. ... Print Settings Printer: Folgertech Prusa i3 2020 Layer Settings Rafts: None Supports: None Resolution: 0.2mm Infill...

The genuine modmic cable clips are far to expensive for this little plastic in my opinion. So i designed them for 3d printing. ...Works quite well for me.</p><p>Single wall print, add brim to hold it to the print bed.</p>

I designed a custom adapter to integrate Bose QC35 headphones with an Antlion ModMic. This adapter is directly linked to the original Bose audio cable, secured by inserting the 2.5mm RCA connector. You will require four M3 screws to assemble the...

Very basic clip for the modmic Microphone. I only did a few iterations that it feels good enough. I wanted to not glue the magnet in place since that was the first thing failing on the original. The cross is intentionally too thin to print well, it...

This small holster allows you to hang up your ModMic Wireless anywhere you like. It's intended to be used with another fastener - e.g. velcro, 3M VHB or double sided tape. There is a cutout so you can see the status LEDs whilst it's in the...

Designed for the Antlion ModMic Uni/USB. I made this so that I would not have to use the double sided tape on my nice new headphones. This one was made to be attached to the headband of the Phillips Fidelio X2HR. I'm sure that minor adjustments...

After my AKG K99 headphone connectors stopped working, I decided to buy a pair of earbuds as a replacement, but I wanted to hold on to the convenience of using a modmic. This versatile bracket gave me the best of both worlds. Print Settings Printer...

A basic charging station for the MODMIC WIRELESS by Antlion Audio!

A quick revision to the modmic base that gives more surface for better adhesion on more stubborn surfaces

<p>The small adapter has a fin that screws in behind the cable guide. ...Original screws can be used. The modmic adapter clip seats in the recess.

A holder for the AntLion Audio ModMic dongel to see the status. ... I glued it to the bottom of my monitor with double sided tape.

This is a simple and easy way to extend the battery life of your ModMic Wireless by up to 200%.Spacer is to fille the gap between the battery and pcbTo install the Antlion ModMic Wireless Oversize Battery Cover:Remove the original battery cover and...

It is almost like the original, but with minor tweaks for 3D-printing.I use this for my ModMic Wireless, and it works great. ...Consider getting new doublesided tape as well (3M mounting tape or something like that).</p><p>I've printed this...

The K7XX headphone clip is designed to securely hold a ModMic microphone in place, ensuring optimal sound quality and minimal interference. This sturdy clip attaches easily to the headphones' earcup, providing a stable base for the microphone to...

You'll need to attach a 6x2 millimeter magnet along with some 3M adhesive to enable using your microphone on an alternate headset. ...In certain cases, applying glue may be essential to secure the magnet in place properly.

<p>Add a 6x2 mm magnet and some 3M adhesive and you can use your microphone on another headset. ...It might bee necessary to use glue to get the magnet to stay.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p...

... AKG K712 headphones. ...This handy accessory snaps over the mini-XLR headphone cable socket, creating a flat surface perfect for attaching the Modmic's anchor. ...The result is a non-destructive and hassle-free way to enjoy your favorite audio gear.