diy ipad tripod mount 3d models

... Air 2 with a full smart case. The maximum thickness is 11.5mm. The tripod mounting plate attaches with a 1/4-20 screw and hex nut. ... I printed this with supports and used PETG because I plan to keep this in my car and didn't want it to warp.

Revisit your blog for details on using a tripod mount that fixes an iPad to a quick release tripod, offering more stability than using the camera's mounting screw. This design suits a Miranda Titan TP2, with rectangular hole dimensions of...

This is a mounting frame to place an iPad inside an Otterbox case on a tripod to use it for an automated photobooth. The frame is in three pieces, one slides on, the other two are held on first by the T nut used to mount to the tripod. The nuts I...

I've needed an iPad-Pro 11" mount for my good old Manfrotto tripod. * Two M4 nuts and M4 x 22mm Hexagon screws are required. I've used the following "Things" for my project: - M4-Nut-Placeholder: https://www.thingiverse.com/thing:794519 -...

... designed so that it would be super easy to print without any supports. Plus, I added a slot for an additional pin from my tripod mount. ... Other hardware I used: - A 1 1/4"x8" hex head bolt - A 1 1/4" nut - A 1 1/4" flat washer - A 1 1/4" wing nut

... without any supports, making the process even smoother. Additionally, I included a slot for an extra pin found on my tripod mount. ... Other hardware utilized: * 1 1/4"x8" hex head bolt * 1 1/4" nut * 1 1/4" flat washer * 1 1/4" wing nut

Needed a larger holder for 8th gen iPad with a Zugu Case,18mm thick. ...Have the tripod holder as one piece and also in two piece tongue and groove for smaller printers

This is a simple iPad-3 mount for a regular tripod. It contains 6 parts, requires 2 pieces of aluminum bar 1/2" x 1/8" (about .2" x .05"), one M3x16mm screw and one M6x12mm hex bolt. Print two copies of side.stl and decide whether to use top.stl or...

This is a way for you to attach your iPad to any 1/4-20 thread tripod. You'll need a few things to make this design work which I will try to make clear below Any suggestions for design improvement are welcome IMPORTANT: Cover all surfaces that will...

This device enables educators to securely attach an iPad or comparable device to a tripod, perfect for conducting virtual classes and meetings on platforms like Zoom. To ensure stability, the two base holes may require rethreading using either a...

But I wanted it to be a bit bigger so I could mount an iPad for my kids to do piano lessons via Zoom without any issues. I decided to make it chunky because I didn't want to save some plastic and risk it being too weak to hold an expensive iPad. I...

Mount your iPad mini with confidence using a sturdy STM case that fits like a glove, while also accommodating the sleek design of the iPad Air model with effortless precision.

A versatile holder designed to securely attach an iPhone (6 to 7 plus) or an iPad mini to a tripod, featuring a standard 1/4"-20 screw attachment on a sturdy tripod head. Created using the powerful Fusion 360 software. ...Printing Details: Printer Brand...

This iPad mini holder is specifically engineered to pair perfectly with an OtterBox Defender case securely attached.

I'm having serious trouble finding a tripod mount that can handle the weight of my 12.9" iPad Pro during long time-lapse photo shoots! To solve this problem, I designed and built a custom holder that securely fits my iPad even when it's wrapped in...

I bought on Amazon a mount for an iPad on a tripod and the 1/4" screw did not fit completely in the mount (not deep enough). ...I designed a disk with the right dimentions in order to ovecom this problem with success.

A mini tripod mount designed specifically for an iPad mini requires just one simple piece of equipment: a 1/4-inch nut easily found at any local hardware store, such as mine which was acquired at Lowe's for the incredibly low price of three cents.

Secure an iPad mini in a sturdy mount that slides from the side, allowing easy access and positioning. At the bottom, a precise hole awaits the tripod screw, requiring careful alignment to ensure proper threading. By placing the screw straight the...

... 31mm in length, while its smallest side measured a precise 25mm. ...This ingenious redesign of the classic square mount was tailored to accommodate tripods of similar dimensions, ensuring a snug yet stable fit that met my exacting standards.

This is a way for you to attach your iPad to any 1/4-20 thread tripod. This version utilizes heat press inserts instead of bolts, its a more effective design however it uses parts less commonly available You'll need a few things to make this design...

... grip, the corners must be adjustable with friction. If you have any questions or concerns, feel free to email me at sphetz@ymail.com or visit my blog at http://sphetz.blogspot.com/2015/02/3d-printed-adjustable-ipad-air.html for more information.

The model has been prepared for 3D printing and is specifically designed for the iPad 4S.

The easel can be printed standing up but the manfrotto mount needs supports under the mount plate.

Since I've been attending Zoom conferences very often since Corona, I needed a sturdy iPad holder. The iPad holder should also be easily adjustable. * In addition to the PLA parts, you need 3 x 30cm x 10mm (stainless steel, aluminum ...) pipe. *...

This is a Tablet / Ipad mount for a Camera Tripod. It is for a 1/4" thread

A personalized rendition of the design found at http://www.thingiverse.com/thing:73622 was created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=73622). Here are the specifications used for this version: base...

Customized version of http://www.thingiverse.com/thing:73622 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=73622 Instructions Using the following options:...

... design from Samkass (thanks!) and used TinkerCad for size adjustments in the walls. You can customize it further on the provided link before printing with support, removing support, attaching to tripod, and inserting your iPad Mini for photo-taking.

Consists of an adapter that mounts to the tripod using a standard 1/4 x 20 nut, and various size adapters that allow the iPad or iPhone to easily slide in from the top of the mount. The adapters use 4 M3 screws (8mm) and nuts, and are designed to...

iPad holder with tripod mount 1/4 and Screws