diy iem shell 3d models

I've designed a universal IEM shell based on my ear impression, which has undergone multiple revisions. I'm eager to hear your feedback - hopefully, you'll find it meets your expectations. ...Unfortunately, I haven't had the chance to test print it yet,...

14mm planar iem shell (not tested)

DON'T DOWNLOAD, I'M WORKING ON A NEW DESIGN Here's my attempt at a universal IEM shell after trying to use OnShape. I was part of a group that couldn't find a universal shell model to make their IEMs, so I decided to create one. I haven't printed it...

This is a free for all shell design I made for a fellow maker in the Head-Fi Forums. ... It is a universal In Ear Monitor Shell taken inspiration with VE EVE in-ears.

Two different universal IEM shells modeled after my ear impressions. These are meant for 0.78mm 2-pin connectors, SLA printing is recommended. ...Just mirror the model to get the left side, you can add bores to the nozzle as needed in meshmixer.

I need something to protect my iem when I leave my desk. Easy to print no support needed. ...0.2 layer height

DIY 9V PP3 battery shell, harvest terminals from old alkalines, file them down to the size. ... Two Li-Ion 602040 500mAh cells fit nicely inside.

Print this design using a DLP or SLA printer... This model should fit a two to four speaker configuration with two to three id2mm od 2.5mm tubes. ...In other words, use the following part numbers: 22955, plus 29689/33aj007, plus 29689/33aj007, plus...

For IEM's with very stiff ear-hooks, like Campfire Audio's cables, there is sufficient slack above the IEM compartments to lay the ear hooks flat so that only the cable is wound around the post. ... The large sized case is still about 1/3 smaller than...

I decided to give my old airplane earbuds a new life by taking them apart and putting them into a semi-custom In-Ear Monitor (IEM) housing. *I've Uploaded My Own Right and Left Ear IEM's as an example* **To make your own, follow these steps:** 1.

Storage box for in-ear monitors. ... I also printed some padding in TPU to avoid scratching my IEMs but just some fabric will do.

Storage box for in-ear monitors.I also printed some padding in TPU to avoid scratching my IEMs but just some fabric will do.

A frame and slider to hold and IEM inside of the IEC711 Stick Style Microphone.Use Blu-tack on the slider to create a better grip on the IEM. ...Use these Heat-Set inserts (https://www.amazon.com/gp/product/B07TZ37HXJ) and a M3 Bolt to lock the slider...

Designed this to hold a microphone, IEM, spare batteries and a card to signify the singer. I've included the Fusion 360 files so you can modify it to your needs. ...

The IEM right was obtained from an original scan of 123d design. ...Following, is a modified version, incorporating precise cuts that create an optimal seal while accommodating space for the speaker.

Resin or small nozzle fdm. ... Needs an added rear vent on the faceplate. More details on the build here: https://www.head-fi.org/threads/home-made-iems.430688/page-961

Simple display stand for displaying IEMS on a desk. ...Headphones can orient multiple ways on the stand, it has space for the coiled cable and a 1/4" adapter

Simple display stand for displaying IEMS on a desk. ...Headphones can orient multiple ways on the stand, it has space for the coiled cable and a 1/4" adapter

Basic design of a holder for IEM-style earphones, cable hangs off the edge of whatever surface the stand is placed on to keep it straight and free from knots, base can be screwed or stuck to surfaces to prevent the stand from moving but in my...

The problem is that I needed a strain relief to keep the IEM earbuds from pulling out of the extension cable.This clip is designed to slide over a belt or the waistband of your pants and then slide a loop of cable into it to provide strain relief for...

Sometime IEM (In-ear monitor) don't come with a clip for attaching the wires behind the head. This is a clip that rapidly design to solve this problem. ...PS: When the clip is assembled, it is really harde to deconstruct it so clip it at the right place...

If you're like me and like to use your IEMs with the cable tucked inside your shirt, you'll know how annoying it is when you get a bit sweaty and suddenly the cable starts tugging. This clip solves that issue while also alleviating the cable noise...

The KSC75 IEM Adapter was born into existence in August of 2021 from one man's love for budget Hi-Fi. Designed over the span of an arduous 24 hours this Hi-Fi modification is guaranteed to bring you the KSC75 sound, but forced through a funnel and...

&nbsp;I felt the container that came with my IEMs was too small and cramped, so I made a larger container. &nbsp;This model also makes a great earplug case when scaled down in size.</p><p>I've printed several of these in eSun ePA and various brands...

Sennheiser ew g4 IEM - CASE

A proper, 3d printable IEM shell with 3 parts! The nozzle, chamber and faceplate. Use 10mm drivers, and short MMCX connectors for the chamber (Feel free to edit the model to your desired connector and shell shape type). However, it is highly...

This is a remix of an existing IEM case. ...I wanted the top to be a bit shorter as I didn't need so much room for my IEMs.

A simple plug and play tuning addon for LETSHUOER S12 planar IEM. ... Printed with no supports, 0.12mm high quality PLA. Currently I use 2mm thick sony IEM tuning foams for dampening, great, but not perfect. ...Feel free to improve it.

You'd want to use it if you don't want excess skin oil penetrates your IEM cable over time and turn your cable green or soggy. This ear hook can support cable with diameter up to 3mm. Use the "Solid" version to print with solid filaments (PLA, ABS,...

“Hook” works well for typical behind the ear cable IEM, “cutout” works well with any kind of earphone and “showerhead” will work well with the so called showerhead or earbud form factor. Spool: The spool simply comes in 3 different variants. “Basic”...