diy filament maker 3d models

A stand and + pen holder where you can easily put your tools. ...A minimal stand where you can put your allenes, pens, notes, screwdrivers.

I was pretty disappointed with the standard extruder on my CTC DIY 3D Printer, so I decided to swap it out for a bowden extruder and an E3D V6 clone. The hotend came with a super tiny (and really loud) 30 mm fan, so I wanted to use the bigger 40 mm...

This mounting system makes it simple to measure the diameter of the filament that your DIY filament extruder is producing. It's designed to work with any dial indicator, as shown here. I've updated the design again, this time making changes on...

You can find DIY YZ Base here: https://www.thingiverse.com/thing:2509242 DIY Z Axis is also available here: https://www.thingiverse.com/thing:2489051 And DIY Y Axis can be found at this link: https://www.thingiverse.com/thing:2507844 DIY Bed Base...

Be proud of the maker that you are, and let that pride shine through by creating and wearing this vibrant DIY tiara! The tiara is precision-crafted with 3D printing technology, designed to hold five BrightDots and an ESP32 development board in...

The designed piece is intended to maintain a stable filament roll on the Anet A8 support.

... you could support me with a coffee! ...You can find more DIY 3D Printer Homemade Thingiverse Videos on my YouTube channel. ...Check out this video: https://www.youtube.com/embed/HyGtGzRSt4M and also this one: https://www.youtube.com/embed/Ch6chmoZa2I

More DIY 3D Printer Homemade Thingiverse Videos can be found on my YouTube channel at UCEN2KAOLu1Pj0Xix9lAi71w. Watch this video to see how to make a 3D printer from scratch: LTS8EvUGBJE. ...Check out another video showcasing a homemade 3D printer...

This robust DIY filament extruder motor, thrust bearing, hopper, and flange assembly efficiently tackles the auger thrust forces that often cause problems with many home extruders. This is a redesign of the front end of the RepRapable RecycleBot by...

... do my best to improve it. For a step-by-step tutorial on installing the filament detector, check out Nathandarnell's blog post: http://nathandarnell.com/adding-filament-runout-detection-anycubic-kossel-marlin-1-1-8-biqu-3d-filament-detection-module

Yet another filament guide for the wanhao i3/maker select v2, but this one has a convenient holder for a piece of sponge that acts as a filament cleaner. ...The bottom_cap part should be a snug fit into the holder; you may need to scale it up or down in...

Check out Leftcetio's model page for detailed instructions.

Here are the original text rewritten with the same tone, voice, and phrasing as the original.

Based on these designs: https://www.thingiverse.com/thing:3061551 (use roller from this one) https://www.thingiverse.com/thing:4272336 (insert PTFE tubes like in this one) https://www.thingiverse.com/thing:4061095 ...

Modeled in Fusion 360. In the files I've included a design for 0.5mm (0.8mm ⌀), 1mm (1.4mm ⌀), and 2mm (2.25mm ⌀) optic fiber - the extra hole diameter accounts for FDM printers outer perimeters tolerances. Cura setting "Outer Wall Inset" used...

... ... Designed specifically for Maker Parts filaments. The spool hole diameter is 58 and the wall thickness is 10. ------------------------------------------- Customized version of http://www.thingiverse.com/thing:605360 Created with Customizer!

After a few tests using the original version of the curved filament guide (see my other remix for a dovetail adapter for Monoprice Maker Select Plus here https://www.thingiverse.com/thing:4601899), I noticed curved arm was too thin and flexible, so...

... it didn't work as expected. I did this remix to reinforce the original one. I hope it serves... Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: No Supports: No Resolution: 0.3mm Infill: 30% Filament: 3d Warhorse PLA black

I keep two spools mounted on the wall above it, as the filament feeds in, it creates quite a bit of noise by rubbing against the steel frame. It's been designed to fit snugly into place of the stock spool holder, although it could also be used with...

Hey Guys this is another mod for Wanhao Duplicator I3, Maker Select, and Cocoon Create 3D Printers - this time it's a filament guide that I've found very helpful in directing the filament exactly where it needs to go. No non-3D printer parts are...

Print Settings Printer: Monoprice Maker Select V2 Rafts: No Supports: No Infill: 15% Post-Printing Installation Unscrew and remove the filament spool holder on top of your printer. Run the screws through the new guide's holes, then place it below...

Filament Feed Spool Brackets for MP Maker Select 3D Printer v2 - A Simple Solution with Two Parts to Print. To assemble this design, you'll need two 75mm long half-inch PVC pipes, two 150mm long half-inch PVC pipes, two 350mm long half-inch PVC...

This solution keeps the filament right where I need it and also alleviates some of the strain on the extruder, as the filament is gravity-fed. I'm currently printing the final pieces for this design and will test it over the next couple of days. If...

My maker select had a z-brace taking up the right two screw slots, so I made a version with a vertical orientation instead. ...Uses the same 608 bearings that the original uses.

... ...The filament cleaner relies on cotton balls, sponges, or foam, which are infused with a few drops of mineral oil for optimal cleaning performance. Version 2.0 boasts a reinforced printer frame mount that significantly reduces filament scraping.

...The clever design utilizes the stock M5 screws to secure the filament guide in place, while the filament holder support bracket provides added stability. ... This design boasts a 3mm wide filament hole, allowing for smooth and uninterrupted printing.

I mad this wheel to guide filament if the spool is set up on the control box instead of on top.

Print Settings Printer: Maker Select (I3 V2) Rafts: No Supports: No Resolution: 0.1mm Infill: 20% Notes: On my Maker Select, I had Simplify3D set to 1.00 and 0.65mm; however, I increased the multiplier to 120% on the printer itself. It seemed like...

This printer is extremely difficult to handle when using PLA, resulting in filament breakage that's become a major nuisance. The filament often breaks by accident, making it unbearable to touch. Furthermore, I've had the misfortune of ramming my...

I designed this for side mounted spool holders to feed and retract filament, providing a consistent pressure to the extruder at all times. Ideal for any side mount that doesn't come from above - I don't recommend that unless you're working outside...