diy equatorial mount 3d models

A telescope mount with Nema motors attached and a suitable gear set of gear ratio 3*3*120.

A telescope mount with Nema motors attached and a suitable gear set of gear ratio 3*3*120.

Remix of Simon's equatorial mount, to adapt it to a tripod with 3/8" threaded shaft.

The A to Z assembly, including the wedder, equates to an equatorial mount. ...However, there's still much more to accomplish and it requires considerable effort.

Currently working on converting the affordable equatorial mount included with my Orion Starblast II 4.5" telescope. ...Utilizing a MasterCraft caliper to take precise measurements.

UPDATED: 24 JUN 2022 Updated assemble instruction for 3D printed parts ↓↓↓↓↓↓↓↓ https://mr-deep-addicted.com/?page_id=1300 Full 3D Printed Equatorial Mount. RA: 1:180 DEC: 1:45 With Microsteps 1/16 RA: 1:6400 DEC: 1:400 The heart of this equatorial...

My DIY mount comes equipped with some handy controls: a four-axis joystick lets you manage two axes and focus settings, while an on/off toggle switch lets you switch between the equatorial drive and fine-tuning modes. An added rotary encoder makes...

Equatorial telescope mount / adaptor Work-in-progress as I have yet to finish the controller board, code and test the mechanisms. Uses 4 Slew bearings of the thing below, and lots of M3 bolts. ... https://www.thingiverse.com/thing:4979666 OnShape...

Check out his instructables for more details on how to assemble https://www.instructables.com/id/Equatorial-Mount-for-DSLR/ Changes: -Changed motor to nema 17 -Added another reduction (4:1) -Changed to chevron gears -Replaced all screws with M3 (was...

DEC_Housing_Back1_PCBSupportUPDATED: 24 JUN 2022Updated assemble instruction for 3D printed parts↓↓↓↓↓↓↓↓https://mr-deep-addicted.com/?page_id=1300Full 3D Printed Equatorial Mount.RA: 1:180  DEC: 1:45With Microsteps 1/16 RA: 1:1600  DEC:...

This is my state-of-the-art astrophotography tracking system, a precision traveling equatorial mount that rotates its turret with unparalleled accuracy. The turret rotates 360 degrees in exactly 23 hours, 56 minutes, precisely matching the sidereal...

The mount design is modeled after the Losmandy GM8, featuring a sturdy and reliable construction.

2 units are required for use as a dual-axis (RA & DEC) equatorial mount. BOM for 1 Unit 1 x 6812ZZ Bearing-60x78x10 1 x 6807ZZ Bearing-35x47x7 6 x 606ZZ Bearing-6x17x6 1 x 17hs4401s-pg5.18: 1 (Geared Steppermotor) 1 x Aviation Plug GX12...

If you're struggling to locate the clutch handles on your EQ6 mount in the dark, consider swapping out the original black metal ones for glow-in-the-dark ABS handles. I even replaced those on my tripod legs, which are identical, to prevent tripping...

Greetings all, my French study project centers around the right ascension axis of a telescope intended for use in Alsace.

All of my projects were printed with a Prusa Mk3S. - 12V battery - 1 arduino - 1 cnc shield or electronics to run a stepper motor - 2 buttons - 1 screen - 1 on-off switch - 1 lead weight - 1 Flange Other than 3D Printed parts: - 1...

You can find all the details for building an equatorial mount for your DSLR camera over at Instructables, specifically on this project: https://www.instructables.com/id/Equatorial-Mount-for-DSLR/.

I made a simple stepper motor (nema17) support to motorize an equatorial mount. The brand of the mount is Mizar. ... The telescope is 114/900 Mizar.

all of the details are on instructables here : https://www.instructables.com/id/Equatorial-Mount-for-DSLR/ or on my Instructable account

I utilize Arca Swiss Mounting System and swapped out the Base for the Equatorial-Mount. The Arca Swiss is extremely common, so I believe others will adopt this too. As a resident of the Cologne area, I adjusted the angle to 51° (the latitude-based...

This is an interface to mount a Nikon DSLR on an equatorial mount (the celestron CG-2). The part is introduced directly in the mount dovetail. Needed : Screw M4 x 16 mm Nut M4 Screw 1/4" (photo) Printed in PETG for the thermal resistance. ... ...

The EQ2 Equatorial Mount adapter is a clever creation that allows you to attach your camera to the mount plate with ease. To get started, you'll need a 1/4" captive screw measuring exactly 10.5mm in length. This will give you a secure hold on the...

A larger version of my static wedge to allow a Celestron Nexstar Mount to track in equatorial mode. This one fits mounts such as the Nexstar 114 GT, with a upper cone diameter of 125mm (the original one fits 100mm, and can be found here:...

I do not know the brand and model of my equatorial mount, but you might be able to remix these brackets and gears to fit your particular mount. ... Dave Ek's Digital Setting Circles: https://eksfiles.net/digital-setting-circles/ DSC ASCOM driver:...

A Static wedge to allow a Celestron Nexstar Mount to track in equatorial mode.This one fits mounts such as the Nexstar 80 GTL, with an upper cone diameter of 100mm (for an upper cone of 125mm, see https://www.thingiverse.com/thing:4879004). I've...

This kit aids in initial polar alignment of your equatorial mount. The included plummet (plumb bob) is attached to the mounts counter weight shaft and a second plummet to the mount center bolt. These will settle on points on the ground that should be...

This design is based on SimonRob's Equatorial Mount for DSLRs (https://www.thingiverse.com/thing:4365068), but it's been upgraded to handle smooth tracking on a lightweight telescope setup. A huge thanks to him for laying the groundwork, and I...

The central hole diameter measures 19mm, making it an ideal fit for Takahashi EM-11 equatorial mounts. Printing in PLA material is highly recommended. A 25% infill is typically sufficient for most cases, while a lower infill of 10-20% can...

To align my Meade Equatorial Wedge, I decided to use a green laser and devised a jig that slips in the hole and secures the laser pointer. I designed this tool in SolidWorks 2013, exported as an STL file and printed on MakerBot Replicator 2X using...

An EQ mount for the Dwarf II Smart Telescope