diy ender 3 enclosure 3d models

This is a rough mesh change in MeshMixer to make it fit in the enclosure by shortening the support bar. ...I also changed the cable clips to make them fit a usb cable, as I'm using the WYSE in Webcam mode with Octoprint and a Raspberry Pi Original...

- Hole for data cables moved to side to allow for shorter cables and let you push the enclosure back - Enclosure (halves) now bolt to power supply, as well as each other and rear - Fixed a "half-blind hole" issue in rear plate of enclosure - Added...

Remixed version of this to fit Ender 3: https://www.thingiverse.com/thing:4405355 See the original version for the parts missing (top, LCD etc) Because of the fact that i only have a skr mini e3 and a rpi 3b+ i cant remix other versions. Changed...

This enclosure contains: A Raspberry Pi 3B for running OctoPrint, A BigTreeTech SKR E3 mini main board or the Stock Creality Ender-3 mainboard. (optional) A Google AIY Audio Hat with Speaker and microphone, 2 LM2596 Step down converter for providing...

The problem: I have a tent enclosure which limits the space between the printer and the walls of the enclosure. I was able to find a box that fit in the space for my first few prints with the camera in place, but I needed a better solution. ...

Remixed from https://www.thingiverse.com/thing:4790166 I needed a new enclosure for my 3KR EZ and loved this design, but it wouldn't work in its current form. Just did a simple adjustment to the screw holes and widened the USB/MICROSD slots and...

I wanted an electronics case to mount under my lack enclosure. This case allows enough room for the board, fan, and two buck converters (if you use them for your fans). ... The supports for the case are necessary for the lid slots and are easily...

Here's a revised version of the text: This is a custom remix of the standard hinge included for the IKEA Lack enclosure. The cut measurements provided for the doors fail to account for the bottom plate of the hinge. ...To resolve this issue, I removed...

... lowers the IO holes and standoffs for the Raspberry Pi 4. I needed this to fit a small extra component inside the enclosure. I've printed this and the Pi still fits perfectly! ... No supports needed to print if oriented like the original model.

I was looking to install an electronics case under my main enclosure. This particular case offers ample space for the board, a fan, and two buck converters - assuming you choose to use them to power your fans. ... The supports for this case are...

In retrospect now that the enclosure is finished I think not plugging the 2 duplicate screw holes and using relatively short screws and pre-drilling the holes into the leg would have been good too. Regardless I am happy overall though the entire...

I modified the case size to fit the power cable going into and out of the case. ...its cleaner and attached to the side of the ender printer. ... you still can reach the power button and/or use mqtt / homebridge / Siri to fire up the printer

I fell head over heels for the sleek design of Gweeps' rear electronics enclosure! The fact that it's specifically designed with a Raspberry Pi 4 in mind is just genius, don't you think? The way the USB and Ethernet ports are cleverly switched to...

I love it, so I made my custom mix, which means: - the base: https://www.thingiverse.com/thing:3083358 - electronic case: https://www.thingiverse.com/thing:3945794 - sd card holder: https://www.thingiverse.com/thing:3336576 - cable mount inside the...

Pressure-fit the nuts in to the case, then mount the case to the frame of your printer with M4 T-nuts (fits on an Ender 3 v1 at least). Run cables to the monitor, then screw it all together. **Below are notes from the building process:** ...

...The temperature doesn't exceed 30C after 5 hours with a 220C nozzle and 60C bed, thanks to an air conditioner and the permanently disabled heater behind the enclosure. I have no drawings or specs, but building one shouldn't be too hard without them.

Also made a Side panel with the Ender logo, just cosmetic. It annoyed me that the panels didn't line up on that side. NOTE: I found that the cosmetic panel made the PSU rather warm vs without. So I removed mine. I ran it for a couple of long...

The large holes in the base align with the solid plastic of the original psu enclosure and are only added there to save plastic. The smaller holes are the venting for the base of the PSU where the cabling is usually exposed to fingers. This vent...

Remix of Pi 3+ case to fit Pi4, also reduced thickness of fan mount for shorter screw compatibility and added extrusion for a 12V switch going to my LED strip

I'm still using the stock Ender 5 enclosure for the PSU and ran longer wires to bring in power. The other wiring is stock, with an extra 10-pin cable for the LCD and some DuPont jumpers since I didn't have the tools to crimp new ends for the Duet. ... I...

2 Plywood 8mm x 440mm x 500mm 3 Acrylic 3mm x 220mm x 500mm 2 psc 4 Screws 4mm x 20mm 10 pcs 5 Screws 4mm x 25mm or 30mm 10 pcs 6 Screws 5mm x 40mm 4 pcs 7 Double Sided Adhesive Tape 8 Toothpick to fill the holes 9 Acoustic Foam 50mm x 450mm x520mm...

2 Plywood 8mm x 44mm x 50mm 3 Acrylic 3mm x 22mm x 50mm 2 psc 4 Screws 4mm x 20mm 10 pcs 5 Screws 4mm x 25mm or 30mm 10 pcs 6 Screws 5mm x 40mm 4 pcs 7 Double Sided Adhesive Tape 8 Toothpick to fill the holes 9 Acoustic Foam 50mm x 45mm x52mm to be...

It uses 3 x M3 screws to seal the case (they can be short, as in 10mm to 20mm), and 2 x M3 PC Computer Motherboard screws to mount the Pi to the inside of the casing. I fitted my case on the rear right side of my BIQU B1 printer. Thats it, nothing...

You will need: * [Threaded...

This is a custom Electronics front enclosure designed specifically for Ender 3/Ender 3 Pro users. ...It's engineered to fit perfectly with these popular models: * Bigtreetech SKR 1.4/1.4 Turbo boards * Raspberry Pi 2/3 computers * Four LM2596 power...

DIY Lack table enclosure for BIQU B1 ============================= ** PARTS FOR PRINTING** ------------------------------------- Just as with the Prusa design, most of the printed parts are organized into sheets of multiple parts that are all...

This is an innovative Electronics front enclosure designed specifically for Ender 3/Ender 3 Pro, perfectly tailored to fit:\r\n\r\nBigtreetech E3 Mini\r\nRasperry Pi 2/3\r\n4x LM2596\r\n1x Noctua Fan 40x40\r\nThe design has been cleverly divided into...

I did my first one with warm white, and liked it a lot, and then I wanted them all the same for consistency (I have 3 of my 4 BIQU B1’s in these and I’m building a 4th enclosure for the 4th B1), and I personally prefer the warm white kind. I think...

This is a remix of 0110-M-P's case https://www.thingiverse.com/thing:922740 specifically made to install it inside my DIY 3D printer enclosure with fan taking the air from the room, not the one circulating in printer. Features: - Cooling fan...

This is an Electronics front enclosure for Ender 3/Ender 3 Pro, it is designed to fit: Bigtreetech E3 Mini Rasperry Pi 2/3 4x LM2596 1x Noctua Fan 40x40 The design has been splitted in 4 parts, use selftapping screws 2.5 x 15 mm to join the parts and...