diy cpap hose holder 3d models

DIY Breathing Device Made from Household Items A homemade respirator is created using everyday household objects. A stainless steel saucepan serves as the base of this makeshift breathing device. An oxygen tank provides a steady supply of life-giving...

Just an adaptor to allow drying of CPAP hose.60mm fan to 22mm hose, perfect for Resmed Airsense 10 hoses but please check.Make sure to use a high powered fan, I found the Noctua NF-A6x25 a little weak.

I wanted a clamp that could be screwed, or stuck with 3M tape, that could fit multiple sizes of hose There is no reason you couldn't use this for any tubing of any size.. ... Everything is customizable

CPAP Hose Holder Clamp (22mm) Specifically Designed to Fit Sleighbed Headboards with a Radius of ~44mm and a Front Tangent Angle of 30 Degrees. Printed in PLA at an infill of ~15%, this clamp can be easily reshaped by submerging it in hot water or...

This adjustable clamp needs to fit multiple hose sizes without restriction; it should seamlessly accommodate tubing of all dimensions. What's more, every aspect of this design is fully customizable. Instructions are simple: use this versatile clamp...

Remixed to add a hose clamp to my IV stand CPAP Station The stand I have: IV Stand Floor Stand, Pitch-It, 2-Hook Three Leg, 30007-012 - Sold by: Pack of One https://www.amazon.com/dp/B07X9VSRK5/ref=cm_sw_r_apan_glt_fabc_VCC9M83KNBFFSCT7SN3A

Remixed to add a hose clamp to my IV stand CPAP Station The stand I have: IV Stand Floor Stand, Pitch-It, 2-Hook Three Leg, 30007-012 - Sold by: Pack of One https://www.amazon.com/dp/B07X9VSRK5/ref=cm_sw_r_apan_glt_fabc_VCC9M83KNBFFSCT7SN3A

The nozzle fits onto the other end of the CPAP hose, allowing me to blow dust out of my printer instead of using canned compressed air. This same setup powers my laser air assist nozzle through a 10mm (ID) silicone hose. You can find more...

 I keep my CPAP in my night stand drawer to minimize clutter so a hose clip on the side of my night stand makes sense.Versions Included – 2 sizes - 18mm hose clip and 19mm hose clip, both with these variants:WSWN = with screw hole, with nub...

This is an adapter which will allow you to attach a standard CPAP hose to a Versaflo M-200 mask (I'm guessing it will also fit other Versaflo models, but the only one I have is an M-200). The tolerances are pretty tight (intentionally, since this is...

My friend relies on a ResMed AirSense10 CPAP machine for better breathing, but he's encountered a frustrating issue - the small connector that links the hose to the mask is prone to stress cracks due to its slender design and can only be obtained as...

I rest my CPAP hose on a cradle by my bed when not in use, but was worried about dust and debris falling into it. To avoid this, I've created this vented plug. The plug covers the top of the tube while letting some air through via small vents at the...

My cpap mask-to-hose swivel elbow got lost, so I made this one. Works with ResMed Quattro Full Face mask, may work with others. 22mm hose diameter, 23.5mm mask input diameter. There are two parts--the collar and the elbow. The collar slides onto...

This is an adapter which will allow you to attach a standard CPAP hose to a Versaflo M-200 mask (I'm guessing it will also fit other Versaflo models, but the only one I have is an M-200). The tolerances are pretty tight (intentionally, since this is...

CPAP

I bumped up its size by 110% so it would snugly fit onto a 50mm wide sleigh bed frame. ...I also downsized the tube clamp to accommodate my 17mm diameter CPAP tube with ease.

I added the 9 volt battery enclosure and the switch holder, that also protect the wiring. The V1 is designed for round 5mm switches and the V2 is for 15.2 x 9mm rocker switch (as in pictures). The blower can be powered by either one 9 volt battery...

Snaps into place firmly and the hose will not pop out.You can skip the screw and use double sided tape if you prefer.Total print time is ~1 hr if you make it solid by increasing wall count to >7 (at 0.2mm per wall). Fusion 360 file included...

A cpap tube and mask holder to fit over a 50mm thick bedhead

Headboard holder for ResMed AirMini CPAP machine. My headboard is a hair over 30mm wide so I modeled this for that. Note, the supports on my print failed so the picture is with a lot of glue while I wait for more black PLA to arrive from Amazon.

This print is to hold a CPAP mask and an additional headband. &nbsp;The shelf is flat on top and curved on the sides to brace the head tubing properly.&nbsp;</p><p>This is designed specifically for the ResMed AirFit P30i Nasal Pillow mask but will...

My cpap mask didn't apply enough pressure on my nose, so I printed this spacer that pushes the mask into the nose further.

Keep your CPAP tubes securely locked together at night to prevent them from coming loose while you sleep. ...This adapter is designed for use with both Philips Respironics System One tubes and Philips DreamStation tubes, ensuring a seamless connection...

This mitten is designed to divert excess air and the "anti-panic" from cpap machines used to prevent apneas. Since sleeping with a partner can be quite bothersome when blowing excess air, especially in winter, this should be helpful. ...By the way, I...

My cpap mask didn't apply enough pressure on my nose, so I printed this spacer that pushes the mask into the nose further. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .1 Infill: 100 Filament: Overture...

I couldn't help but play with the design. Size is 29 mm approx. I printed with no raft or supports, and first layer size was .8.........You might need to use a knife or small screw driver to separate the teeth. ... Category: Parts

I just had to tinker with the layout. The diameter is roughly 29 millimeters. I went ahead and printed it without any raft or support structures, and the initial layer thickness came out to be about .8 mm... ...You may need a utility knife or an Allen...

CPAP Sleep Apnea Hanger Holder support

three sizes to pick from these will fit ResMed face mask i use the cpapholder(1).stl the MED and LG is the size of middle the mask would sit on