diy cpap hose holder 3d models

To lengthen my CPAP hose, I needed a connector and decided to create one in Tinkercad. The cone-shaped coupler tapers from 22mm to 22.5mm for easy slide-on attachment. After printing it without support, using 2 extra shells, 10% infill, and a .27mm...

... newer version is printed in a wood PLA. I was looking for a solution to pick my CPAP hose up so it wasn’t between my bed and nightstand. I also wanted to be able to hang it during the day. ...This will mount to an adjacent wall, or the headboard.

The CPAP Hose support is engineered to be versatile, accommodating any filament type. Nighttime sleep disturbances were my reality, as my hose would constantly fall and wake me up. To solve this issue, I strategically placed the support above the...

I drape my CPAP hose over my headboard at night. After adding a hose cozy, I found that it would slip back down and then tug at my mask waking me up. So I made this clip on ring that would prevent it from sliding back down. What I've found is that it...

I was looking for a solution to pick my CPAP hose up so it wasn’t between my bed and nightstand. I also wanted to be able to hang it during the day. ...This will mount to an adjacent wall, or the headboard quite firmly using command strips.Print...

Coupler for keeping CPAP hose together so it doesn't come unhooked in the night.  Also likely good for extension cords or any other connections in need of reinforcement.Separate variables for:Internal lengthOverall internal diameterSeparate...

A visitor requested a CPAP Hose Guide near their bed, so I designed and tested this solution. The bore is 20mm, and the two parts come together with a paperclip bent through the hinges and clipped short. For my standard hose, it slides through...

A hose coupler for a Mirage Quattro mask. ...

A hose coupler for a Mirage Quattro mask. Category: Replacement Parts

 This is designed specifically for the ResMed Climate Line Air 11 hose but as most hoses are universally sized I'm sure this will work for most.I included two prints, one has an inner ridge to prevent the hose from sliding and the second without...

I always wrestle with getting my hose completely submerged while washing it in vinegar and water, but it inevitably flops around and gets stuck with air pockets, so I designed these clips to keep the hose straight and allow air to escape freely.

I always struggle to fill my hose with water and vinegar for cleaning without getting trapped air in part of the length, so I designed this cap to seal off one end when filling the other. ... Scale up or down in both dimensions if your hose is 22...

I built this bracket specifically to attach securely to the leg of my bedside table, keeping the hose firmly in place so it doesn't slide between the bed and the table, and preventing me from accidentally pulling the machine off its stand. Since the...

... into the hose, I cleverly incorporated a slot for the ResMed Airsense 10 Filter. The compatible fan size is 30x30x10. I'm also offering this assembled product on Etsy at https://www.etsy.com/listing/726051081/cpap-sleep-apnea-cpap-hose-blowerhose

Adapter to use a Ryobi P738 inflator to dry a standard CPAP hose This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/dOsroe37IZW Remix of https://www.tinkercad.com/things/bhjCOVOHQoh-ryobi-pump-lock-attachment

You may find other uses for joining 22mm CPAP hoses. The Y adapter handles three 22mm hoses. The one in the photos is printed with Prusament PLA using .25mm layers. ... The .stl model includes a removable base to increase bed contact area and prevent...

I remove the nose piece from my Philips Dreamstation CPAP in the morning to clean it, but I'm not comfortable with the hose being exposed all day, as it could attract bugs crawling into the hose. ... That's why I designed a simple hose cap to solve this...

This is a caddy I created to hold my CPAP hose and mask on the bedhead. This was my first parametric design so keep that in mind if there are any issues. This caddy was designed around the features of my specific bedhead, however there is no...

I needed this Y adapter so I could clean my CPAP mask and Airsense 10 unit at the same time with my VirtuClean O3 cleaner, instead of wasting a cycle when cleaning separately. There may be other uses that you may have for joining 22mm CPAP hoses. The...

This bracket is specifically designed to alleviate excessive strain on the hose near the port when using a CPAP machine at an elevated position, such as on top of a dresser. It does so by holding the hose securely in place. A recent design update...

I wanted to shorten my CPAP hose due to my CPAP setup. Instead of purchasing another shorter hose, I was able to cut an old hose and use this printed coupler to screw the pieces together. No glue needed, and it isn't leaking! I printed the...

This seems like a solid replacement for much more expensive off the shelf hose dryers. Only supports needed are build plate to accommodate the two notches in the part that fits into the fan exhaust. CPAP machines need to have the hose and mask...

This is a dryer to attach to your CPAP hose after cleaning it to allow it to dry. I noticed that when I cleaned mine, if I hung it to dry water droplets never dried and I thought that was a bad thing. After plugging it into my hose for the first...

This will connect 2 hoses together to give you a really long hose. ... Only the first hose needs to be heated if you are looking for heat.

I had a problem with the hose on my ResMed AirSense 10 disconnecting from the supply hose to the face mask hose. I designed this clip to solve the problem and hold the hoses together. Printed it on end with custom supports on the opposite side. ...

I had the idea bc ik someone who has a CPAP and putting your CPAP mask on the floor is gross. ...and it has been a few months and I came up with this final product (IMPORTANT: supports needed, clean often, you can resize it will not matter that much I...

This is a base designed specifically for holding the AirSense 10 CPAP machine securely on a nightstand. The base wraps snugly around the bottom of the machine and features two extendable tabs that ensure a firm grip on the tabletop. ...To keep...

Use this holder to attach your mask to your bed.

... their surroundings with their noses, so I needed a safe haven for my mask that would shield it from unwanted sniffing or sloppy licks. This nifty holder does just the trick, keeping my mask protected while also being super convenient to use.

Centrifugal Fan to CPAP Hose Adapter This adapter is specifically designed for use with centrifugal fans that have a 53mm x 27mm opening. It attaches securely to the CPAP hose connector, providing a reliable connection. ... Note: This adapter is not...