diy blue snowball stand 3d models
311014 3d models found related to diy blue snowball stand.myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
A shorter name for the small, blue spherical microphone is often referred to as a softball, but I am not your mom.
thingiverse
... stand does require these rubber bumpers. 10mm x 4mm https://amzn.to/2HCik22 You may also be able to find them at your local hardware store. Rather buy it? Get it here: https://www.etsy.com/listing/897026717/blue-snowball-low-profile-stand
myminifactory
So, here's my collection of ultra-simple stands for the Blue Snowball microphone. There's a super compact one that could be useful for gaming or displaying on a shelf. Next up is a "tall" model that I designed to sit at mouth level on my desk. ...Part...
thingiverse
I designed a basic shock absorber for my Blue Snowball. To make it, you'll need: 2 inner ring pieces, 2 outer ring pieces, superglue, and at least 8 hair bobbles. First, thread the bobbles through each loop and attach them to adjacent pins. The...
thingiverse
I tightened the assembly for holding my microphone's legs to the stand too much, causing it to crack around the screw hole. This made the lower part of the stand loose, so it would spin whenever I picked up the mic. I designed a new part based on...
thingiverse
Mount the Blue Snowball to your table lamp stand using this part.
thingiverse
An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small...
thingiverse
Exact same as mrzood's design, except I added matching threads on the stem so the Blue Snowball Microphone is even more secure.
prusaprinters
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball.I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. ...The stand is slim, but sturdy and sits...
thingiverse
The main improvement is that this new design can be used on the original Blue Snowball microphone stand. To assemble it, you'll need one M3 screw to attach the outer ring to the threaded part, as well as some rubber bands or hair ties to secure your...
prusaprinters
This is a remix of a couple of shockmounts I found on Thingiverse.My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand.One M3 screw is needed for mounting the outer ring to the threaded part. And of...
thingiverse
The compact blue Snowball microphone stands 10 millimeters tall on its slender stand.
thingiverse
I crafted this design to overcome the standard maximum height limitation that didn't meet my needs. ... To achieve the desired outcome, I utilized a 20% infill, eschewing both raft and support features during the printing process.
cults3d
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...
thingiverse
This is a replacement part for the Blue Snowball mic stand. Factory plastic parts on the legs are subjected to considerable pressure, making them prone to breaking. To create this part, simply print with an infill of about 35-40%. No supports are...
prusaprinters
ad895 had made the design for the original nice all metal Snowball stand. I wasn't as lucky when I bought mine, and got the other cheap, partly plastic, stand. The mount needed some changes as the stands have different diameters.The downscaled...
thingiverse
Ad895 had initially created a solid metal stand for the original Snowball, but unfortunately, I ended up with the cheaper, partly plastic alternative when I purchased mine. The mount required some modifications because the stands have varying...
thingiverse
I'm looking for a straightforward replacement for my worn-out blue snowball mount that snapped when I clumsily let it fall, requiring a simple new stand that can be installed without any adjustments.
thingiverse
A sleek device designed to secure a blue snowball microphone in place.
thingiverse
A clamp and screw created to hold your blue snowball microphone. ...Prints in three different pieces designed to require no glue, all pieces should fit together snugly.
thingiverse
I built this pop filter using my Blue Snowball mic as the foundation. ...I bonded parts one and two together with super glue, then slipped a knee-high stocking over the ring, trimming the excess fabric with ease before securing it tightly at the base...
thingiverse
I'm excited to remix my original blue snowball mount into two new sizes: small and large. To make it even more versatile, I've added adjustable height options. ... To ensure a secure fit, you'll need 6 M4x8 screws for the height adjustment mechanism.
prusaprinters
A simple, easy to print, desk mounted holder for the Blue Snowball microphone! You will need 3 screws with a maximum thread diameter of 3.5 to 4mm. Print instructionsSimply print flat on the bed with the wide mouth facing upwards, no supports needed....
thingiverse
This is a pop-filter for the "Blue Snowball" microphone. Simply insert a piece of pantyhose between the two parts, click them together and you're done. The filter attaches to the shaft of the microphone as a clip. This is my first upload to...
thingiverse
A Quick SketchUp Design of a Snowball Mountain This sketch will cover the basics of creating a quick mountain design using SketchUp. It's perfect for when you need to create a simple landscape in a short amount of time. To begin, make sure your...
thingiverse
To ensure an ultra-tight seal, the stand and outer ring are precision-engineered with zero gap between them. ... The inner ring is a perfect match for the diameter of the microphone itself, allowing it to be easily pressed around the connecting ring...
thingiverse
Key differences from other mounts was the use of through-hole bolt-in mounts, a cord-clip, and precise thread printing for the five-eighths-twenty-seven Microphone mount on the Blue Snowball and Blue Snowball iCE's OEM Stand. What you Need For this...