diy 3d scanner

Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier Spieler. Die Grundidee habe ich von hier übernommen: ...

Feel free to do whatever you want with them.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

Keep your stuff from falling out.BullNose Freight Ten: https://www.prusaprinters.org/prints/143750-freight-ten-bullnose-model-science-fictionSingle Cab Freight Ten:...

A steel axle would be overkill but a 3D printed one is replaced in minutes and you can use anything with a diameter of 5mm as an axle.Tighter construction -&gt; less wiggling of the parts. Feels sturdy.</li><li><strong>No need for support</strong> in...

... to change a few files to get this working. Those are the files I have added to the project.The remaining files are mostly from the Voron Switchwire / 1.8 / Trident / 2.4 STLs downloadable from https://www.vorondesign.com/Category: 3D Printer Parts

Beim ChaosRun handelt es sich um ein kleines 3D gedrucktes LED Spiel für den kleinen oder großen Zeitvertreib und je nach Spiel für bis zu vier Spieler. Die Grundidee habe ich von hier übernommen:...

... machine. I remain open to suggestions or requests for modifications, but do note that since it is based on the Kossel Mini which is GPL, this project is also distributed under the GPL. Don't like it? You're free to remix it! Category: 3D Printers

... Now I could home the printer and send it to 0,0,0 and the needle should go right to the front left corner which it did.Print SettingsPrinter:Qidi X-ProRafts:NoSupports:NoResolution:.15Infill:20Filament: Hatchbox PLABlackCategory: 3D Printer Parts

Here you are!Designed for use with “Way Basics Eco Stackable Storage Cube, Cubby Organizer (Tool-Free Assembly and Uniquely Crafted from Sustainable Non Toxic zBoard paperboard), White”...

Use with your narrative in the hive or megalopolises of your wargaming environs.Print with “Fill Pattern” as "Adaptive Cubic" to save time and filament.No supports are required.Printed at .20mm Quality.Takes a little under 2 hours to print.Designed...

... <p>Added Dock-V1.1: uses far less resin than Dock-V1 (Update untested and not included in the step file)</p> <p>Added Duct V-1.1: More consistent refill behavior. Keeps the resin level more steadily than V1 Category: 3D Printer Parts

The Gryphon is a mostly 3D printable, hobby-grade, Nerf semi-automatic flywheel blaster. Its main design features are as follows:Uses 130 to 180 sized 20.4mm , brushed DC motors.Semi-auto by rack and pinion with 1:3 gear multiplication. The trigger...

This is my design of a toy meant to teach children about the effects of an inclined plane on a rope/pulley system and the forces involved.  There are 4 3D printed parts in total and 7 externally sourced common hardware materials.  OpenSCAD Source...

There are configurable-text-based creations, multi-line label, gadget display stand, sweeping name plate, bunting banner, customizable text box III, pyramid text, name plate, Customizable text box with lid and round text. Have also a look at my...

... loading filament on each lane to test if the chamfers cut on the smaller tubing is enough to prevent the filament from getting stuck, and to see if the small tubing is seated correctly. Rechamfer/reseat as required Category: 3D Printer Accessories

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.Enforced supports are required on verticle pipes (see files).Superglue the valve handles.Start pumping that...

Much of that comes from off world crates.Build!&nbsp;Get back in the Fight!Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Four sizes - large to small.Lumber stackFour pieces of loose lumberStack or glue, make a...

I found printing 16 a time eventually one clip would pop off and ruin the batch, the ears add enough bed adhesion to keep any from popping off, and it makes taking the pieces off the bed easier. Comments greatly appreciated, let me know what you...

(see the images).Superglue the nose to the body (see the images).Superglue the top deck.Leave the main gun to swing freely.Print supports only on the arches of the nose (that's how I printed it, it might print ok without them).Superglue works best...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

The parts list and assembly instructions are below the video:Parts List3D printed parts:2 sides, 1 flywheel, 1 retaining ring, 1 cluster gear, 1 collar, 1 eccentric, 1 link, 4 bars, 2 legs, 2 feet, 1 hook, 1 pull ring. Print all parts in the...

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

No short circuits between the V G and/or S wires. Hardware I used these end-stops: https://aliexpress.com/item/32959048821.html I am not affiliated with AliExpress nor TwoTrees and there are LOADS of identical/rebranded switches out there. You will...

Don't let them destroy your home.&nbsp;Build!&nbsp;Get back in the Fight!&nbsp;Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Two sizes - Large and Small.Stack for use or glue.The buildings are stackable, use...

The gear end is the front.No supports are required.Superglue works best for gluing it together.Will scale easily if you want a larger or smaller...

The tray should now slide into place.Installing Drawers/Trays under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will need to slide a “Rail Lock Upper” into place on the back of...

[ ] 3D Print included stl files [ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan case. [ ] sunlu_gauge_ring.stl -- circular slip ring for mounting the hygrometer to the front of the case. [ ]...

NOTE: I may be biased, but I think this set would make an excellent project for students of 3D printing. &nbsp;</p><ul><li>The design relies on the accurate printing of close-fitting pieces, which can require particular attention to the physical...

Take what's theirs and make it your own! More Armour!Demolior Class Heavy Tank - https://www.printables.com/model/135967-tank-demolior-class-heavy-deathhead-ii-model-scien Scopulus Class Heavy Tank -...