ditto glasses 3d models

https://newdimension.company.site/Before we begin, I'd like to thank ktothestank for his 250mm Bridge Test Model which I used in these tests. Slicer: Cura 5.1.0Resolution: 0.2mmNozzle: 0.6mmPrinter: Creality Ender 3 ProModifications: Creality...

When we talk about universal accessories, each pack has: Tails of a fox (Kitsuni), raccoon, cat, rabbit, fantasy tail, succubus tail with customized physics for realistic animation Japanese traditional masks (3 pcs) with different skins 3 variants...

Wearing: The mask is designed to be worn with glasses, therefore the tip is not needed to be worn right between the eyes, although it can’t be excluded to be a good fit to someone. Consider the tip be rested in about the middle of the nose. If it...

The LED channels have a profile of 11mm x 3mm and are chamfered at the ends to allow easier threading of the LED strips through the channels. The STL files used for the revise LED guides: LED_guide_one_piece_style2 v6.stl I printed these pieces using...

This fixture will not work on voltage outside of the 90-132V AC range and internal damage may occur when higher voltage is applied to the lamps.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments...

Our standard unit ships with 5600K unless different color temperature is specified.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of...

Our standard unit ships with 5600K unless different color temperature is specified.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of...

Use safety glasses, and proper work gloves when assembling. When using sharp objects never apply force towards body or hands. When using glue follow the manufacturer’s instructions, especially those regarding contact with skin, eyes, and...

However, I personally find the handling less cumbersome with the rubber band, especially since I like to remove the drag-knife for axis homing.Install the cutting padSpeaking of cutting pads, I highly recommend using a magnetic bed with a coated...

Our standard unit ships with 5600K unless different color temperature is specified.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of...

My Maker already had the one-piece Y-plate, with the hot bed 3-point lock mounted on it, with a PEI over borosilicate glass build plate, held with binder clips. You can read more about that is THIS shameless plug: ...

Larson Electronics offers an explosion proof dimmer switch that can be installed within the hazardous location.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break...

1755 Material MAIN CATEGORIES Car Paint (71 + 71 materials) Ceramic (93 + 93 materials) Concrete (30 + 30 materials) Fabric: Canvas, Denim, Knitting, Linen, Silk, Terry, Tweed-Damask, Velvet (303 + 303 materials) Food (20 + 21 materials) Gemstone (39...

I have named this lamp "Tiffany Lamp nach Art des Frimmels" as the design idea was to use the idea of Tiffany glass art. The lamp was originally published by me on Thingieverse some time ago in order to cheer people up a bit during the early days of...

The halves need to mate together.On my glass build surface, I used 3M 77 to stick the PLA parts down. To remove the delicate antenna parts, I let some isopropyl alcohol seep under the edges until the parts slid off the bed without...

But I've printed ten of these, on glass, out of PLA, and only had one failure out of ten.  The HDMI recess part and the SD card slot on the SD side of the case have sacrificial layers. You will need to cut these layers out with an X-acto...

... facing forward. This locking tab can be used with any version Micro Swiss and clones hot ends. With this setup I have been able to make great ABS prints with no warping with the Bowden setup and the Creality glass bed (part cooling fans off). ...

I'll get you your custom STL in less than 24h, usually right away.Step 8: PRINT THE LCD PROTECTORPrint the back glass protector 0.8mm.stl in something rigid (like PLA) and glue it into the recessed spot on the back of the mount. Why? In hard crashes...

You only need one or two of these, depending on whether you are going with a single or a double traveling object configuration.The basic model consists of the following six pieces:2 unique body halves ('Half 1' and ‘Half 2’);2 springs/flippers...

Our standard unit ships with 5600K unless different color temperature is specified.Unlike the glass tube design of traditional fluorescent lamps, these LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of...

Any places there should be "glass" you just need to find some clear plastic packaging (or whatever) and cut it to fit. You can use a $10 heat gun to warm up the plastic if you need to add or remove a curve (takes a bit of practice to avoid melting...

By applying IPA inside and outside with a brush multiple times (with longer pauses to let it dry) the part becomes transparent - almost like glass:Don't forget to let the part dry for another week or even longer, to get rid of the residual IPA in the...

 (My angle grinder and a flap wheel make this a short job.)A good pair of safety glasses.  (Seriously, you only have one set of eyes, please protect them from flying metal and plastic bits!)</li><li>A smooth surface that will survive you pounding on...

With the Digital Bird system I can mount a vastly superior camera system with any glass I choose. 2) Flexibility: The next day I can use the same camera system for a completely different task. Nothing is restricting my choices and I am...

Mirror Sheets Self Adhesive Non Glass Mirror Tiles (11.9” x 17.9”):...

It truly needs to be smooth like glass. I ended up with 3D printing artifacts pressed into my visor so it is harder to see. Other option for creating the buck beside 3D printing is to mill the buck from soft wood and polish it. - **Visor**:...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to upgrade.The...

In the event that of an LED failure, the mating LED will continue to operate.Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during operation. Instead of heating a small filament or...

Our standard unit ships with 2800K unless different color temperature is specified.Unlike the glass tube design of traditional fluorescent lamps, the LED T-Style lamps have no filaments or fragile housings to break during operation. Instead of using...

The 3D printing model’s chosen scale is 1:32 for the FFF/FDM version and 1:64 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 142 parts;- A printed model is 168 mm tall, 240 mm wide, 448 mm deep;- Gull-wing...