dirt bike phone mount 3d models

Engine plates for a 125 Dirt bike machined from 6061 Aluminum

When running mousse on your dirt bike, and need to plug the valve stem hole.

A college project of mine involved designing an electric dirt bike concept; however, it remains unfinished.

With ZWIFT now offering offroad options, I wanted a sturdy mount for my phone on my road bike. Although this design appears robust, I'm not certain how it would perform in off-road conditions. I created two versions: Version 1 is quite strong and...

This is a bike phone mount that utilizes the widespread magnetic design used by car phone mounts. It's straightforward with no moving parts and should work with any phone, as long as it has a metal plate on the back. Given its simplicity, there are...

Instructions for customizing this design are below: Using the following options, you can customize your new mobile phone holder: Phone length: This value represents how long or short you want the dock to be based on the type of phone you plan to...

Dirt bike stand. For 1:18 bikes. ...Printed on ender-3 at 1mm, took 50 min to print and came out great.

Summary: Custom Iphone 5s E Bike Mount Created with Tinkercad. Edit Online at https://www.tinkercad.com/things/lCIV4QPWKGQ. ...Designed for MakerBot Replicator 2 Printers, No Raft or Support Needed.

Models and drawing for dirt bike stand manufacturing. ...Names and some notes are in slovak but I do not think this matters.

... and a little prior knowledge of the slicer settings at a relative high speed (up to 120mm/s ; moderate travel speed;80°;225°;PETG). I'm currently using this mounting system on my bike. ... https://www.youtube.com/watch?v=NPF1dzPdFUA&feature=youtu.be

Hello, This is a remix/copy of Bike Mount by 3D-IN. You have step files to further remix this thing in order to fit your bike or whatever, and you can use them however you see fit. To fully assemble this, the rest of the pieces that you'll need are...

This phone mount are primaly made for Crosscall phone with X-link feature. So phone could be recharged even under bad weather. The mount are for motorbike handlebar with middle beam. Used with two large rubber band and rubber patch like in...

This phone mount is an adaptation of a design found on Thingiverse, specifically the item with ID 366322. To accommodate standard rubber cases, the mount has been enlarged to fit larger phones. A clip and slot have now been integrated into the...

http://www.thingiverse.com/apps/customizer/run?thing_id=912161 This is my attempt to design a bike mount for the Galaxy S6 FRE case. ...I used the measurements found on this...

This is an adaptation of http://www.thingiverse.com/thing:366322 NOTE: the mount has been designed to fit a standard phone with a rubber case in place.\n Just incorporated a clip and slot feature for printing ease. \nThe mount can be fully printed,...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=912161 Instructions Using the following settings: Phone Handlebar Diameter: 25mm Phone Width: 72mm Corner Radius for Phone: 10mm Phone Height: 9mm Bridge Height: 20mm Phone Length: 139mm

iPhone5s Bike Mount. This design is inspired by a similar project on Thingiverse: https://www.thingiverse.com/thing:366322. I adapted this original design to fit my bicycle perfectly. To improve its durability, I tightened the casing by 1 mm and...

... Instructions Using the following settings: Phone width: 66 units Handlebar diameter: 35 units Bridge height: 25 units Phone corner radius: 10 units Phone length: 130.5 units Phone height: 11.5 units

Customized Version of Thingiverse Model 912161 Created with Customizer Tool at Thingiverse Website Instructions Using the Following Options: Phone Width Set to 66 Units Handlebar Diameter Measured at 35 Units Bridge Height Set to 30 Units Phone...

This is an iphone 6s phone mount I designed as a proof of concept. The design prints in three parts. This is designed for a set of carbon fiber handlebars of 30mm dia. where if tightened too far, the print will fail before damage is done. To...

iphone5s bike mount. This is inspired mostly by https://www.thingiverse.com/thing:366322 I ve adapted the original design to my bicycle. I made the casing tighter (by 1 mm) and made the "arrow" wider as my first make broke after 150 km of use.</p>...

this is meant to be tucked between a dirt bikes front tire and fender when being tied down, then when you tighten your tie downs it doesn't compress your forks the entire time the bike is tied down. i used 30% infill. ...Just print both halves and glue...

Phone Length Set at Maximum Customization Value Customization settings were optimized using advanced algorithms for a precise fit. Using a unique combination of features to enhance performance. These specific settings are: Phone Corner Radius: 10...

The instructions, printed on a MakerBot, detail how to attach an HTC Sensation phone onto the handlebar stem of a bicycle.

This model has been tailored specifically for use with a Nexus 5X phone, paired with a transparent polycarbonate case. A customized version of http://www.thingiverse.com/thing:912161 has been created using Customizer! Access the customization tool at...

Additionally, the selection includes dirt and road tires as well as three unique wheel types: classic spokes, custom designs, and solid construction. The color palette offers seven vibrant options: dark blue, light blue, green, orange, purple, red,...

Two taller pieces have been added to accommodate thicker phones, such as those equipped with Pop Sockets. All parts print effortlessly without supports in the provided orientation. Print parts at a resolution of 0.2 or 0.3mm, except for the nut,...

Added two taller pieces for thicker phones (Pop Sockets and the like). All parts print without supports in the orientation provided. Print parts at 0.2 or 0.3mm except for the nut, that needs to be done at 0.1mm in order to get decent threads. You...

... incorporating a spring to keep the "claw" open. Other items used in this project include: 1x 8mm Threaded rod. 2x 8mm Stainless steel rods. 2x 8mm Locking nuts. 1x 8mm Butterfly nut A GoPro mount and one or two GoPro extensions were also utilized.

This plaything, designed to look like a real dirt bike, is crafted from sturdy wooden materials for durability and safety during playtime. ...The wood construction adds an authentic touch while ensuring that it's gentle on little hands and the floor.